Question about 1997 Jeep Grand Cherokee

1 Answer

O2 sensor Where is the high voltage O2 sensor? My check engine light is on and I was told that was the code they got, but they can't tell me witch one it is. I changed the one by the manifold but my check engine light is still on

Posted by on

  • jason goddard May 11, 2010

    whats the code it will tell you what sensor it is

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 277 Answers

Suggest you disconnect the Battery for 15 minutes., Negative Post. Reconnect and take a run out of about 25 miles of mixed Highway, to enable the ECM to REBOOT.
Regards,DT

Posted on Sep 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The check engine comes on but I dont lose power the code it is showing is sid 152.does anyone know what it is.


some codes dont cause power loss or may not even notice anything wrong but a check engine light a p0152 code means following answer courtesy of OBD-CODES.com === P0152 O2 Sensor (High Voltage) OBD-II Trouble Code Technical Description Article by Dale Dale Toalston ASE Certified Technician 02 Sensor Circuit High Voltage (Bank 2 Sensor 1) What does that mean? The o2 (oxygen) sensors basically measure oxygen content in the exhaust. The PCM (powertrain control module) then uses this information to regulate fuel injector pulse. The o2 sensors are very important to proper operation of the engine. Problems with them can cause the PCM to add or take away too much fuel based on the faulty o2 sensor voltage. A P0152 code refers to the Bank 2, sensor 1, o2 sensor. (Bank 1 would contain cylinder 1 and bank 2 is the opposite bank. Bank 2 doesn't necessarily contain cylinder 2.) "Bank 2" refers to the side of the exhaust that DOES NOT contain cylinder number 1 and "Sensor 1" indicates that it is the pre-cat sensor, or forward(first) sensor on that bank. It is a four wire sensor. The PCM supplies a ground circuit and a reference voltage of about .5 volts on another circuit. Also for the o2 heater there is a battery voltage supply wire and another ground circuit for that. The o2 sensor heater allows the o2 sensor to warm up faster, thus achieving closed loop in less time than it would normally take for the exhaust to warm the sensor up to operating temperature. The O2 sensor varies the supplied reference voltage based on oxygen content in the exhaust. It is capable of varying from .1 to .9 volts, .1 indicating lean exhaust and .9 indicating rich exhaust. NOTE: A condensed explanation of fuel trims: If the o2 sensor indicates that the oxygen voltage reading is .9 volts or high, the PCM interprets this as a rich condition in the exhaust and as a result decreases the amount of fuel entering the engine by shortening injector "on time". The STFT (short term fuel trims) would reflect this change. The opposite would occur when the PCM sees a lean condition. The PCM would add fuel which would be indicated by a single digit positive STFT reading. On a normal engine the front o2 sensors switch rapidly back and forth two or three times per second and the STFT would shift positive and negative single digits to add and remove fuel to compensate at a similar rate. This little "dance" goes on to keep the air/fuel ratio at it's optimal level. Short term fuel trims or STFT reflect immediate changes in fuel injector "on-time" while long term fuel trims or LTFT reflect changes in fuel over a longer period of time. If your STFT or LTFT readings are in the positive double digits (ten or above), this indicates the fuel system has been adding an abnormal amount of fuel than is necessary to keep the proper air/fuel ratio. It may be overcompentsating for a vacuum leak or a stuck lean o2 sensor, etc. The opposite would be true if the fuel trim readings are in the negative double digits. It would indicate that the fuel system has been taking away excessive amounts of fuel, perhaps to compensate for leaking injectors or a stuck rich o2 sensor, etc. So when experiencing o2 related issues, reading your fuel trims can indicate what the PCM has been doing over the long term and short term with regard to fuel. This code indicates that the o2 sensor was stuck too high or in the rich position. The PCM monitors this voltage and if it determines that the voltage is too high out of range for too long, P0152 may set. Symptoms Symptoms may include: MIL (Malfunction Indicator Lamp) illumination Engine may run very rough Engine may be running lean or rich depending on if the o2 sensor is reading correctly or incorrectly Lack of power Increased fuel consumption Causes Potential causes of an P0152 code include: Bad bank 2, 1 o2 sensor incorrectly reading rich condition Engine running rich and o2 sensor Correctly reading rich condition Signal shorted to voltage in harness Wiring harness damage/melted due to contact with exhaust components Vacuum leak (make have lean codes (P0171, P0174) present with it) Leaking injectors Bad fuel pressure regulator Bad PCM Possible Solutions If you have any lean or rich codes associated with this code, focus on fixing these first because these can cause the o2 sensor voltage readings to appear to be faulty when they are in fact only reading correctly. So, with the engine running at operating temperature, use a scan tool to observe the Bank 2,1 o2 sensor voltage reading. Is it high? If so, look at the long term and short term fuel trim readings. The fuel trims are affected by the o2 sensors as noted above. If the LTFT reading for that bank is indicating negative double digits (PCM trying to take away fuel to compensate for problem) try inducing a vacuum leak to see if the sensor voltage then goes lean and the fuel trims increase. If the o2 sensor responds, suspect a problem with the engine, not the sensor. There may be other engine codes to help you. If the o2 sensor reading remains high (0.9 volts or above) and won't respond then shut off engine. With KOEO (Key on engine off) disconnect the o2 sensor and look for signs of corrosion or water intrustion. Repair as necessary. The voltage reading should now be about 0.5 volts. If so, replace the o2 sensor, it's shorted internally. If after unplugging the o2 sensor the voltage reading on the scan tool doesn't change, then suspect wiring problems. Inspect the harness and look for any melted wires or anywhere that the o2 sensor harness is making contact with the exhaust components. If you are unsure, you can check for continuity of all four wires between the sensor and the PCM with an ohmmeter. Any resistance at all indicates a problem. Repair as necessary.

Read more at: http://www.obd-codes.com/p0152
Copyright © OBD-Codes.com

Jul 28, 2015 | Cars & Trucks

1 Answer

Bank 1 lower oxygen sensor - replaced with mopar sensor check engine light still on


Hi Larry:
DTC P0138 - O2 Oxygen Sensor Circuit High Voltage (Bank1, Sensor2)
The Heated Oxygen Sensor (2) located rear of catalytic converter produces an output signal relative to oxygen storage capacity of catalytic converter. Ho2S 2 signal is less active than signal produced by front oxygen sensor. This code sets when HO2 Sensor voltage is greater than 999 mV for more than 2 minutes (time depends on model. Could be as high as 4 minutes)

There may be no noticeable symptoms except for MIL illumination. Possible high fuel pressure can over rich the system.

A code P0138 may mean that one or more of the following has happened:
Faulty O2 sensor
Short to battery voltage in O2 sensor signal circuit
High fuel pressure (not as likely)

Here are some potential solutions:
Replace O2 sensor
Repair short to battery voltage in o2 sensor signal circuit

Check it; hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Mar 01, 2012 | Dodge Stratus Cars & Trucks

2 Answers

Hi there i have 1997 Avalon V6 . the check engine light up # 138 and 401 so can you tell me the name of that two please thnks


Trouble codes are normaly 4 digits with a "P" or "B" before it. I am gonna assume that you meant P0138 and P0401:
P0138 is Oxygen Sensor Circuit High Voltage (Bank 1, Sensor 2)
P0401 is Exhaust Gas Recirculation Flow Insufficient Detected

A code P0138 may mean that one or more of the following has happened:
  • Faulty O2 sensor
  • Short to battery voltage in O2 sensor signal circuit
  • High fuel pressure (not as likely)
Possible Solutions Here are some potential solutions:
  • Replace O2 sensor
  • Repair short to battery voltage in o2 sensor signal circuit
for info on the P0401:
http://www.obd-codes.com/p0401

Jul 10, 2011 | 1997 Toyota Avalon

1 Answer

1998 Jeep Cherokee Sport w/ 4 liter in-line 6, I have a check engine light on and the hand held diagnotic unit is telling me "BANK 1 SENSOR 1 HIGH VOLTAGE". What is the cause(s)?


Your O2 sensor needs to be replaced. These sensors constantly out put voltage from .1 volts up to 1.3 volts, your sensor is stuck in the high range. It is the first O2 closest to the engine.

Sep 08, 2010 | 1998 Jeep Cherokee 4WD

1 Answer

I have a 2002 Chevy S-10 Crew cab 4wd LS. I was


p0420 is Catalyst System Efficiency Below Threshold (Bank 1) o2 sensors reading are used to check the cat if the cat is plugged you will lose power o2 sensor send a voltage signal to the computer 0 to 1 volts The o2 upstream of the cat should switch back and forth from 0 to 1 volts, average .450v if voltage stays high engine is running rich (low oxygen) if voltage stays low engine is lean (lots of oxygen) cats have a 8-year 80000-mile warranty

Jul 11, 2010 | 2002 Chevrolet S-10

4 Answers

Engine light poo38


That is the oxygen sensor on bank 1 down by the cat converter.

Oct 21, 2009 | 2004 Jeep Liberty

2 Answers

O2 check engine light


U may indeed have a faulty MAF or O2 sensor, the way to tell if the MAF or a vacuum leak is at issue is that both O2's will code lean, if only one codes lean then it is most likely just a faulty O2 sensor, I don't have your codes but this is the way we do things at the dealer for problems like yours. Remember the O2's are before the Cat's., after the Cat's they are called Cat efficiency monitors in the book.

Jan 03, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

1999 dodge dakota p1762 code


dont know lots about this witout engine size but some have 1 coil per cylender possible coil is bad or plug 02 sensor will cause some problems but a miss fire will cause it to run like trash

Oct 08, 2008 | 1999 Dodge Dakota

Not finding what you are looking for?
1997 Jeep Grand Cherokee Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...