Question about 2000 Kia Sephia

1 Answer

The power steering pressure hose was not properly installed.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 113 Answers

Bring it back to who put it on

Posted on Sep 05, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

stormbrewin
  • 426 Answers

SOURCE: replaced power steering hose 1500 chevy pickup

Maybe got an air lock/bubble

Posted on Oct 11, 2008

chuck943
  • 783 Answers

SOURCE: high pressure power steering hose - one or two?

Here is a pic.

[IMG]http://i253.photobucket.com/albums/hh43/chuck943/DG1690A.gif[/IMG]



1 3A674 Power Steering Pump 2 3A714 Power Steering Pressure Hose 3 3C510 Power Steering Hose Bracket 4 3N824 Power Steering Pressure Switch 5 3504 Steering Gear 6 3A713 Power Steering Return Hose (Gear to Cooler) 7 3D746 Power Steering Fluid Cooler 8 3493 Power Steering Return Hose (Cooler to Pump

Posted on Feb 23, 2009

c17hydro
  • 2984 Answers

SOURCE: high pressure power steering hose leak 97 chevy 4x4

Very simple and no special tools. Take your time and put some rags or a oil pan underneath it and wrench away!

Please don't forget to rate!!!!

Posted on Mar 14, 2009

  • 1596 Answers

SOURCE: My power steering pressure hose has a leak.

i pERSONALY WOULD REPLACE IT MYSELF EVEN WITHOUT MY 30yrs Of Experience in this Field. I have Enclosed Instructions for you to use. PLEASE dont Forget to RATE me As MOST folks DONT remember to that is how WE Get our Ratings such as GURU THANK YOU and Good Luck On The Job, Dont PAY a dime If YOU CAN > D I Y

REMOVAL PROCEDURE

  1. Remove the power steering pressure hose (2) from the power steering pump (1).
  2. Raise the vehicle on a hoist. Refer to Vehicle Lifting.
  3. Remove the front exhaust pipe, automatic transmission only. Refer to Intermediate Pipe Replacement in Exhaust System
  4. Remove the power steering pressure hose (1) from the power steering gear (3).
  5. Remove the power steering hose retainer (2).
  6. Remove the power steering pressure hose (1) from the vehicle
    1. Install the power steering pressure hose (1) to the vehicle
    2. Install the power steering hose retainers (2). NOTICE: Refer to Fastener Notice in Service Precautions.
    3. Install the power steering pressure hose (1) to the power steering gear (3). Tighten the fitting to 27 Nm (20 ft. lbs.).
    4. Install the front exhaust pipe, if removed. Refer to Intermediate Pipe Replacement in Exhaust System.
    5. Lower the vehicle.
      1. Install the power steering pressure hose (2) to the power steering pump (1). Tighten the fitting to 27 Nm (20 ft. lbs.).
      2. Bleed the power steering system. Refer to Bleeding Power Steering System in Service and Repair of Steering.

Posted on Mar 27, 2009

  • 2 Answers

SOURCE: How to replace high pressure hose on steering,

Found a diagram online myself..

Posted on Nov 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How involved is it to replace a power steering pump on a 2007 Explorer 4.0?


Power Steering Pump - 4.0L Special Tool(s) Installer Set, Teflon® Seal
211-D027 (D90P-3517-A) or equivalent Material Item Specification MERCON® V Automatic Transmission Fluid
XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada) MERCON® V
Item Part Number Description 1 388898 Teflon® seal 2 - Pressure line-to-pump fitting (part of 3A719) 3 W700839 Power steering pump bolts (3 required) 4 3A674 Power steering pump 5 W503924 Pressure line bracket-to-engine bolt 6 3691 Power steering pump supply hose 7 W503924 Power steering pump supply hose bracket bolt
Removal
NOTICE: While repairing the power steering system, care should be taken to prevent the entry of foreign material or failure of the power steering components may result.

  1. Using a suitable suction device, remove the power steering fluid from the reservoir.
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.
  1. Remove the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.
  1. Remove the pressure line bracket-to-engine bolt.
  1. Remove the power steering pump supply hose bracket bolt.
  1. Release the power steering pump supply hose clamp and disconnect the hose.
  1. Disconnect the pressure line-to-pump fitting.
    • Remove and discard the Teflon® seal.
  1. Remove the 3 bolts and the power steering pump.
Installation
  1. NOTE:A new Teflon® seal must be installed.Using the Teflon® Seal Installer Set, install a new Teflon® seal to the pressure line fitting.
  1. Position the power steering pump and install the 3 bolts.
    • Tighten to 25 Nm (18 lb-ft).
  1. Connect the pressure line-to-pump fitting.
    • Tighten to 75 Nm (55 lb-ft).
  1. Connect the power steering pump supply hose.
  1. Install the power steering pump supply hose bracket bolt.
    • Tighten to 11 Nm (97 lb-in).
  1. Install the pressure line bracket-to-engine bolt.
    • Tighten to 11 Nm (97 lb-in).
  1. Install the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.
  1. Fill the power steering system. For additional information, refer to Section 211-00.

Apr 13, 2016 | Ford Cars & Trucks

1 Answer

How do i install power steering hose on a 1991 lexus 400


If you notice problem with power steering,the hose has to be inspected,if its faulty it has to be replaced.

=========
For your help,i provide you with few solved helplinks showing how exactly to replace power steering hose:------

How to Remove Power steering Pressure Hose ?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-power-steering-pressure.html

---------

How to replace power steering pressure hose?

http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-pressure.html

--------------
These will help.
Thanks.

Nov 28, 2012 | 1991 Lexus LS 400

2 Answers

Replace power steering pump on 06 chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Jul 08, 2012 | 2006 Chevrolet Uplander

1 Answer

I need to know how to take the power steering off a 1997 dodge caravan?


Power Steering Pump-Let me know if you need to take the power steering gear off: Removal & Installation 2.4L Engine To Remove:
  1. Disconnect and isolate the negative battery cable.
    • Remove as much fluid as possible from the power steering fluid reservoir using a siphon pump.
    • Remove the drive belt from the power steering pump.
    • Loosen the nut securing the front power steering pump bracket to the aluminum bracket.
    • Raise and safely support the vehicle.
    • Place a drain pan under the vehicle to catch the power steering fluid.
    • Disconnect the connector from the oxygen sensor at the rear engine mount bracket. NOTE: The exhaust system needs to be moved to allow room for power steering pump removal.
    • Remove the bolts and nuts securing the catalytic converter to the exhaust manifold.
    • Disconnect the exhaust system hangers from the brackets. Move the exhaust system rearward and left as far as possible.
    • Raise the heat sleeve to expose the clamp and then disconnect the fluid return hose from the steel tube. Allow the fluid to drain.
    • Remove the accessory drive splash shield.
    • Remove the supply hose coming from the reservoir from the power steering pump. Drain the fluid from the hose.
    • Disconnect the pressure hose from the pump. Drain off excess fluid from the hose.
    • Remove the return hose from the pump. Allow the fluid to drain from the tube.
    • Remove the nut from the rear of the pump to the cast mounting bracket.
    • Loosen the three bolts securing the pump to the front mounting bracket. Then remove the nut and remaining bolt.
    • Remove the power steering pump and the front bracket from the cast bracket on the engine as an assembly through the exhaust tunnel.
    • Remove the three bolts attaching the front bracket to the power steering pump and separate the power steering pump from the front bracket.
To Install:
  1. Install the power steering pump through the exhaust tunnel of the vehicle.
  2. Loosely install the nut on the rear of the pump to hold the pump to the bracket.
  3. Install the front bracket on the pump and install the three bolts loosely.
  4. Install the nut and bolt securing the bracket to the cast bracket.
  5. Tighten the three front bracket-to-pump bolts to 40 ft. lb. (54 Nm).
  6. Connect the pressure hose to the power steering pump. Make sure to inspect the o-ring and replace as needed. Tighten the fitting to 275 in. lb. (31 Nm).
  7. Connect the low pressure return hose to the power steering pump.
  8. Connect the supply hose from the reservoir to the pump. Make sure the hose is not near drive belt.
  9. Install the drive belt and splash shield.
  10. Connect the fluid return hose to the steel tube on the cradle and cover with the heat shield sleeve.
  11. Properly position the protective heat sleeve over the return hose. Secure the heat sleeve with a tie strap to the hose to keep it in place.
  12. Install the exhaust system.
  13. Connect the oxygen sensor wiring connector to the vehicle wiring harness.
  14. Lower the vehicle.
  15. Connect the negative battery cable.
  16. Fill and bleed the power steering system.
  17. Check for leaks.
3.0L Engine To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Remove as much fluid as possible from the power steering fluid reservoir using a siphon pump.
  3. Remove the drive belt from the power steering pump.
  4. Raise and safely support the vehicle.
  5. Place a drain pan under the vehicle to catch the power steering fluid.
  6. Disconnect the connector from the oxygen sensor at the sensor wiring harness grommet on the floor pan. NOTE: The exhaust system needs to be moved to allow room for power steering pump removal.
  7. Remove the bolts and nuts securing the catalytic converter to the exhaust manifold.
  8. Disconnect the exhaust system hangers from the brackets. Move the exhaust system rearward and left as far as possible.
  9. Raise the heat sleeve to expose the clamp and then disconnect the fluid return hose from the steel tube. Allow the fluid to drain.
  10. Remove the accessory drive splash shield.
  11. Remove the supply hose coming from the reservoir from the power steering pump. Drain the fluid from the hose.
  12. Disconnect the pressure hose from the pump. Drain off excess fluid from the hose.
  13. Remove the two bolts securing the pump to the alternator/power steering pump/belt tensioner bracket.
  14. Remove the pump from the bracket and remove it from the vehicle through the exhaust tunnel on the floor pan.
To Install:
  1. Install the power steering pump through the exhaust tunnel of the vehicle.
  2. Install the pump on the bracket with the two mounting bolts. Tighten the two bolts to 40 ft. lb. (54 Nm).
  3. Install the pump rear support bracket. Tighten the nut and bolts to 40 ft. lb. (54 Nm).
  4. Connect the pressure hose to the power steering pump. Make sure to inspect the o-ring and replace as needed. Tighten the fitting to 275 in. lb. (31 Nm).
  5. Connect the low pressure return hose to the power steering pump.
  6. Connect the supply hose from the reservoir to the pump. Make sure the hose is not near drive belt.
  7. Install the drive belt and splash shield.
  8. Connect the fluid return hose to the steel tube on the cradle and cover with the heat shield sleeve.
  9. Properly position the protective heat sleeve over the return hose. Secure the heat sleeve with a tie strap to the hose to keep it in place.
  10. Install the exhaust system.
  11. Connect the oxygen sensor wiring connector to the vehicle wiring harness.
  12. Lower the vehicle.
  13. Connect the negative battery cable.
  14. Fill and bleed the power steering system.
  15. Check for leaks.
3.3L & 3.8L Engines To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Remove as much fluid as possible from the power steering fluid reservoir using a siphon pump.
  3. Raise and safely support the vehicle.
  4. Disconnect the connector from the oxygen sensor at the sensor wiring harness grommet on the floor pan. NOTE: The exhaust system needs to be moved to allow room for power steering pump removal.
  5. Remove the bolts and nuts securing the catalytic converter to the exhaust manifold.
  6. Disconnect the exhaust system hangers from the brackets. Move the exhaust system rearward and left as far as possible.
  7. Place a drain pan under the vehicle to catch the power steering fluid.
  8. Raise the heat sleeve to expose the clamp and then disconnect the fluid return hose from the steel tube on the cradle. Allow the fluid to drain into the pan.
  9. Remove the accessory drive splash shield.
  10. Remove the drive belt from the power steering pump.
  11. Remove the supply hose coming from the reservoir from the power steering pump. Drain the fluid from the hose.
  12. Disconnect the pressure hose from the pump. Drain off excess fluid from the hose.
  13. Disconnect the return hose from the pump. Drain the fluid into the drain pan.
  14. Remove the power steering pump rear support bracket.
  15. Remove the three bolts securing the pump to the alternator/power steering pump/belt tensioner bracket.
  16. Remove the pump from the bracket and remove it from the vehicle through the exhaust tunnel on the floor pan.
To Install:
  1. Install the power steering pump through the exhaust tunnel of the vehicle.
  2. Install the pump on the bracket with the three mounting bolts. Tighten the bolts to 40 ft. lb. (54 Nm).
  3. Install the pump rear support bracket. Tighten the fasteners to 40 ft. lb. (54 Nm).
  4. Connect the pressure hose to the power steering pump. Make sure to inspect the o-ring and replace as needed. Tighten the fitting to 275 in. lb. (31 Nm).
  5. Connect the low pressure return hose to the power steering pump.
  6. Connect the supply hose from the reservoir to the pump. Make sure the hose is not near drive belt.
  7. Install the drive belt and splash shield.
  8. Connect the fluid return hose to the steel tube on the cradle and cover with the heat shield sleeve.
  9. Properly position the protective heat sleeve over the return hose. Secure the heat sleeve with a tie strap to the hose to keep it in place.
  10. Install the exhaust system.
  11. Connect the oxygen sensor wiring connector to the vehicle wiring harness.
  12. Lower the vehicle.
  13. Connect the negative battery cable.
  14. Fill and bleed the power steering system.
  15. Check for leaks.
prev.gif next.gif

Oct 13, 2010 | 1997 Dodge Caravan

1 Answer

How to install a power steering pump for a 1997 chrysler seabring conv


Chrysler Cirrus/Stratus/Sebring/Avenger/Breeze 1995-1998
Power Steering Pump - REMOVAL & INSTALLATION

Cirrus, Stratus, Sebring Convertible and Breeze
(see Figures 1, 2, 3 and 4)
  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with an insulator grommet, which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Siphon as much power steering fluid out of the reservoir as possible.
  3. Raise and safely support the vehicle.
  4. Remove the right front tire and wheel assembly.
  5. Remove the splash shield from the right front wheel well.
c901554.jpg

Fig. 1: Power steering pressure hose attachment to the pump-with Variable-Assist steering

8786c07.jpg

Fig. 2: Power steering pressure hose attachment to the pump-without Variable-Assist steering
  1. Disconnect the power steering pressure hose from the pump.
  2. Remove the hose connection on the power steering pump.
e7733b2.jpg

Fig. 3: Typical power steering pump front bracket attachment
  1. Remove the power steering adjusting bolt.
  2. Remove the power steering pump rear attaching bolt.
  3. If so equipped, remove the Anti-lock Brake System (ABS) hydraulic control unit heat shield.
  4. Remove the wheel speed sensor retainer bracket from the right inner fender.
  5. Remove the wheel speed sensor sealing grommet from the right inner fender.
  6. Disconnect the speed sensor wiring.
  7. Push the wiring through the hole in the inner fender.
If not equipped with anti-lock brakes, the hole will just have a sealing plug.
  1. Remove the bolt attaching the power steering front bracket to the mounting bracket. Access to the bolt is gained through the hole for the speed sensor wiring.
  2. Remove the power steering pump drive belt.
  3. Remove the power steering pump and the front bracket as an assembly.
To install:
  1. Install the power steering pump and bracket.
  2. Reinstall the bolt at the adjusting slot, but do not tighten.
  3. Reinstall the bolt mounting the power steering pump to the rear mounting bracket, but do not tighten.
  4. Reinstall the power steering pump top bolt, but do not tighten.
  5. Reconnect the power steering hoses.
b72b14a.jpg

Fig. 4: Install a new O-ring gasket on the hose fitting
Use a new O-ring when reinstalling the power steering pressure hose.
  1. Reinstall the drive belt.
  2. Adjust the drive belt and tighten the power steering pump bolts to 40 ft. lbs. (54 Nm).
  3. Reinstall the splash shield.
  4. Reinstall the tire and wheel assembly.
  5. Lower the vehicle.
  6. Reconnect the negative battery cable.
  7. Refill the reservoir and bleed the power steering system.


Sebring Coupe and Avenger
  1. Disconnect the negative battery cable.
  2. Remove (drain, suction pump, etc.) as much power steering fluid as possible.
  3. Disconnect the return fluid line. Remove the reservoir cap and allow the return line to drain the fluid from the reservoir. If the fluid is contaminated, disconnect the ignition high tension cable and crank the engine several times to drain the fluid from the gearbox.
Cover any components located underneath the power steering pump with a shop towel to protect them from damage due to power steering fluid spillage. For example, the A/C compressor or alternator, depending on vehicle and engine, is below the power steering pump, so cover the A/C compressor or alternator with a shop towel before removing any hoses.
  1. Loosen (but do not remove) the power steering pump mounting bolts and remove the drive belt.
  2. Remove the pressure switch connector from the side of the pump.
  3. Disconnect the pressure line.
  4. Unbolt and remove the pump from the mounting bracket.
To install:
  1. Clean all parts well. Inspect the pump pulley for cracks. Check the hoses carefully for cracks or signs of weakness.
  2. Install the pump, wrap the belt around the pulley and lightly tighten the mounting bolts.
  3. Replace the O-rings and connect the pressure line. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the fitting to 13 ft. lbs. (18 Nm).
  4. Connect the return line and secure with the clamp.
  5. Fasten the pressure switch connector.
  6. Adjust the power steering belt for proper tension and tighten the adjusting bolts.
Use only MOPAR ATF PLUS automatic transmission fluid type 7176, ATF+3 automatic transmission fluid, or equivalent, in the power steering system of Sebring coupe and Avenger models.
  1. Refill the reservoir and bleed the power steering system.

Hope this help to solve it (remember comment and rated this). TY for using Fixya.

May 13, 2010 | 1997 Chrysler Sebring

3 Answers

How do you remove the Power Steering Pump and bracket. I have taken off several bolts but it still is not letting loose. Help


3.0L (VIN 3) Engine

f799ffc.gif
Power steering pump mounting detail (3.0L engine)

  1. Disconnect and isolate the negative battery cable.
  2. Remove the accessory drive belt. The belt does not have to be removed from the engine.
  3. Raise and safely support the vehicle.
  4. Disconnect the wiring harness connector to the oxygen sensor which is accessible through the oxygen sensor wiring harness grommet in the vehicle floor pan.
  5. Remove the catalytic converter from the exhaust manifold and remove all exhaust system hangers and isolators from the exhaust system brackets. Move exhaust system out of the way as far rearward and to the left as possible to provide access to the power steering pump.
  6. Place a drain pan under the power steering pump. Remove the power steering fluid return line hose on the front suspension cradle. Allow the fluid to drain from the pump and hose.
  7. Remove the accessory drive belt splash shield.
  8. Disconnect the power steering remote reservoir supply hose from the fitting on the power steering pump. Allow fluid to drain from the hose.
  9. Remove power steering fluid pressure line from the power steering pump and drain any excess power steering fluid.
  10. Remove the power steering fluid return hose from the power steering pump.
  11. Remove the rear support bracket mounted behind the power steering pump to the engine block.
  12. Remove the 2 mounting bolts that secure the pump to the alternator/power steering pump and belt tensioner mounting bracket.
  13. Remove the power steering pump and pulley assembly out from the vehicle. Transfer all required parts from the pump to the new replacement pump before installation.
To install:
  1. Position the front of the power steering pump up onto the mounting bracket. Torque the 2 power steering pump-to-mounting bracket bolts to 40 ft. lbs. (54 Nm).
  2. Install the rear power steering pump-to-engine block support bracket. Torque the 2 support bracket mounting bolts to 40ft. lbs. (54 Nm). Install the nut to the mounting stud behind the pump and torque to 40 ft. lbs. (54 Nm).
  3. Install the high pressure fluid line to the pump output fitting. Torque the high pressure line-to-power steering pump fitting to 275 inch lbs. (31 Nm). Be sure to inspect the pressure line O-ring for any damage before connecting the pressure line to the steering pump.
  4. Install the low pressure power steering fluid hose to the power steering pump low pressure fitting. Be sure the hose clamps are properly reinstalled and hoses are clear of the accessory drive belts.
  5. Install the accessory drive belt.
  6. Install the hose on the power steering fluid return line on the front suspension cradle. Be sure the hose clamps and heat shield tubes are correctly reinstalled.
  7. Reconnect the exhaust pipe to the exhaust manifold. Install the hangers and isolators onto the exhaust system brackets. torque the nuts and bolts to 250 inch lbs. (28 Nm).
  8. Reconnect the wiring harness connectors to the oxygen sensor. Install the wiring harness grommet into the vehicle floor pan.
  9. Install the accessory drive belt splash shield.
  10. Remove the drain pan and lower the vehicle.
  11. Refill the power steering pump reservoir with the correct amount of clean power steering fluid.
  12. Reconnect the negative battery cable. Bleed the power steering system.
  13. Run the engine and check the system for leaks and proper steering operation.

3.3L (VIN R) & 3.8L (VIN L) Engines

0b3de97.gif
Rear support bracket mounting detail (3.3 & 3.8L engines)

6764c64.gif
Power steering pump mounting detail (3.3 & 3.8L engines)

  1. Remove and isolate the negative battery cable.
  2. Raise and safely support the vehicle. Place a drain pan under the power steering pump.
  3. Disconnect the wiring harness connector to the oxygen sensor which is accessible through the oxygen sensor wiring harness grommet in the vehicle floor pan.
  4. Remove the catalytic converter from the exhaust manifold and remove all exhaust system hangers and isolators from the exhaust system brackets. Move exhaust system out of the way as far rearward and to the left as possible to provide access to the power steering pump.
  5. Remove the power steering fluid return line hose on the front suspension cradle. Allow the fluid to drain from the pump and hose.
  6. Remove the accessory drive belt splash shield.
  7. Remove accessory drive belt.
  8. Disconnect the power steering remote reservoir supply hose from the fitting on the power steering pump. Allow fluid to drain from the hose.
  9. Remove power steering fluid pressure line from the power steering pump and drain any excess power steering fluid.
  10. Remove the power steering fluid return hose from the power steering pump.
  11. Remove the rear support bracket mounted behind the power steering pump to the engine block.
  12. Remove the 3 mounting bolts that secure the pump to the alternator/power steering pump and belt tensioner mounting bracket.
  13. Remove the power steering pump and pulley assembly from the vehicle. Transfer all required parts from the pump to the new replacement pump before installation.
To install:
  1. Position the front of the power steering pump up onto the mounting bracket. Torque the 3 power steering pump-to-mounting bracket bolts to 40 ft. lbs. (54 Nm).
  2. Install the rear power steering pump-to-engine block support bracket. Torque the support bracket mounting bolts to 40 ft. lbs. (54 Nm). Install the nut to the mounting stud behind the pump and torque to 40 ft. lbs. (54 Nm).
  3. Install the high pressure fluid line to the pump output fitting. Torque the high pressure line-to-power steering pump fitting to 275 inch lbs. (31 Nm). Be sure to inspect the pressure line O-ring for any damage before connecting the pressure line to the steering pump.
  4. Install the low pressure power steering fluid hose to the power steering pump low pressure fitting. Be sure the hose clamps are properly reinstalled and hoses are clear of the accessory drive belts.
  5. Install the accessory drive belt.
  6. Install the hose on the power steering fluid return line on the front suspension cradle. Be sure the hose clamps and heat shield tubes are correctly reinstalled.
  7. Reconnect the exhaust pipe to the exhaust manifold. Install the hangers and isolators onto the exhaust system brackets. Torque the nuts and bolts to 250 inch lbs. (28 Nm).
  8. Reconnect the wiring harness connectors to the oxygen sensor. Install the wiring harness grommet into the vehicle floor pan.
  9. Install the accessory drive belt splash shield.
  10. Remove the drain pan and lower the vehicle.
  11. Refill the power steering pump reservoir with the correct amount of clean power steering fluid.
  12. Reconnect the negative battery cable. Bleed the power steering system.
  13. Run the engine and check the system for leaks and proper steering operation.

Nov 03, 2009 | 1997 Chrysler Town & Country

1 Answer

How to r&r powersteering pump 1998 mercury grand marquis


Hopfully this will be ALL you need Besides Pulley REMOVAL TOOL It can be Rented @ AutoZONE

REMOVAL
  1. Remove drive belt.
  2. Raise vehicle on hoist. WARNING: TURN AIR SUSPENSION SWITCH (LOCATED IN LUGGAGE COMPARTMENT) OFF TO PREVENT VEHICLE DAMAGE OR PERSONAL INJURY.
  3. Remove power steering pressure hose bracket.
  4. Disconnect electrical connector at power steering control valve actuator.
    1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley hub. CAUTION: Do not apply in-and-out pressure on the power steering pump shaft. Pressure will damage the internal thrust areas.
    2. Hold the small hex-head and rotate the tool nut counterclockwise to remove the power steering pump pulley.
    3. Disconnect power steering pressure hose at power steering pump and drain fluid into a container.
    4. Disconnect power steering return hose at power steering pump and drain fluid into a container.
    5. Remove four retaining bolts and power steering pump and power steering pump pulley assembly.
    6. Remove power steering pressure switch from pump.
    INSTALLATION
    1. Position the power steering pump on the mounting bosses of engine block and install the bolts at the side of the power steering pump. Tighten to 20-30 Nm (15-22 ft. lbs.).
    2. Connect the power steering reservoir pump hose to the power steering pump and reposition the hose clamp to power steering pump inlet fitting.
    3. Replace power steering pressure hose O-ring.
    4. Install the power steering pressure hose to the power steering pump fitting. Tighten the tube nut with a tube nut wrench rather than with an open-end wrench. Tighten to 34-46 Nm (26-33 ft. lbs.). NOTE: Swivel or end play of the power steering pressure hose end is normal and does not indicate a loose fitting.
    5. Place the power steering pump pulley on the power steering pump shaft and install Power Steering Pump Pulley Replacer T91P-3A733-A. The small diameter threads on the tool should be engaged in the power steering pump shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group.
    6. Hold the small hex-head and rotate the tool nut clockwise to install the power steering pump pulley on the shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group. NOTE: The power steering pump pulley face must be flush within 0.25 mm (0.010 inch) of the end of the pump shaft.
    7. Remove the Power Steering Pump Pulley Replacer T91P-3A733-A.
    8. Remove the shipping tube nut from power steering pump housing prior to installation.
    9. Connect electrical connector to power steering control valve actuator.
    1. Install power steering pressure hose bracket.
    1. Lower the vehicle.
    2. If equipped, turn the air suspension ON.
    3. Install drive belt on the power steering pump pulley.
    4. Fill the power steering pump reservoir with Power Steering Fluid Motorcraft MERCON(r) ATF.

Oct 04, 2009 | 1998 Mercury Grand Marquis

1 Answer

Need to replace high pressure power steering hose on 2004 Monte Carlo SS. Need tips to effectively do the job myself. Tools needed, tricks to make the job easier, what not to do...etc. Thank yiou so much...


Power Steering Line/Hose: Service and Repair
Pressure Hose
Power Steering Pressure Pipe/Hose Replacement (3.8L)
Removal Procedure
1. Place a drain pan under the vehicle.
2. Remove the accessory drive belt.
3. Raise and support the vehicle. Refer to Vehicle Lifting.
4. Remove the tire and wheel assembly.
5. The power steering pressure hose is the lower hose at the power steering gear.
Remove the power steering pressure hose from the power steering gear.
6. Remove the power steering pressure hose from the power steering pump.
7. Remove the power steering pressure hose from the clamps on the power steering gear.
8. Remove the power steering pressure hose from the vehicle.
Installation Procedure
1. Install the power steering pressure hose to the vehicle.
2. Install the power steering pressure hose to the clamps on the power steering gear.
Notice: Refer to Fastener Notice in Service Precautions.
3. Install the power steering pressure hose to the power steering pump.
^ Tighten the fitting to 27 Nm (20 ft. lbs.).
4. Install the power steering pressure hose to the power steering gear.
^ Tighten the pressure hose fitting to 27 Nm (20 ft. lbs.).
5. Install the tire and wheel assembly.
6. Remove the drain pan from under the vehicle.
7. Lower the vehicle.
8. Install the accessory drive belt.
9. Fill the power steering system with power steering fluid.
10. Bleed the power steering system.
11. Inspect the power steering system for leaks.

00d203e.jpg

Sep 15, 2009 | 2004 Chevrolet Monte Carlo

1 Answer

Subaru impreza 1993 power steering leak


YOU CANT USE A REGULAR FUEL LINE ON POWER STEERING AS A HIGH PRESSURE HOSE.BECAUSE POWER STEERING PRESSURE IS 1000 PSI.YOU HAVE TO BUY THE POWER STEERING HIGH PRESSURE HOSE IT HAS NUMBER OF PLIES MATERIAL WEAVES TO MAKE IT STRONG.IT WAS MADE FOR POWER STEERING HIGH PRESSURE.YOU DONT HAVE A BLOCKAGE .THE HIGH PRESSURE HOSE JUST WORE OUT.REPLACE IT .IT SHOULD FIX THE PROBLEM.

Sep 04, 2009 | 1993 Subaru Impreza

2 Answers

My power steering pressure hose has a leak.


i pERSONALY WOULD REPLACE IT MYSELF EVEN WITHOUT MY 30yrs Of Experience in this Field. I have Enclosed Instructions for you to use. PLEASE dont Forget to RATE me As MOST folks DONT remember to that is how WE Get our Ratings such as GURU THANK YOU and Good Luck On The Job, Dont PAY a dime If YOU CAN > D I Y

REMOVAL PROCEDURE
  1. Remove the power steering pressure hose (2) from the power steering pump (1).
  2. Raise the vehicle on a hoist. Refer to Vehicle Lifting.
  3. Remove the front exhaust pipe, automatic transmission only. Refer to Intermediate Pipe Replacement in Exhaust System
  4. Remove the power steering pressure hose (1) from the power steering gear (3).
  5. Remove the power steering hose retainer (2).
  6. Remove the power steering pressure hose (1) from the vehicle
    1. Install the power steering pressure hose (1) to the vehicle
    2. Install the power steering hose retainers (2). NOTICE: Refer to Fastener Notice in Service Precautions.
    3. Install the power steering pressure hose (1) to the power steering gear (3). Tighten the fitting to 27 Nm (20 ft. lbs.).
    4. Install the front exhaust pipe, if removed. Refer to Intermediate Pipe Replacement in Exhaust System.
    5. Lower the vehicle.
      1. Install the power steering pressure hose (2) to the power steering pump (1). Tighten the fitting to 27 Nm (20 ft. lbs.).
      2. Bleed the power steering system. Refer to Bleeding Power Steering System in Service and Repair of Steering.

Mar 27, 2009 | 1999 Pontiac Sunfire

Not finding what you are looking for?
2000 Kia Sephia Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...