Question about 1994 Honda Accord

2 Answers

How do i change my transmission fluid is it a pan or a plug

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 713 Answers

This model as far as I know did not have a drain plug in the tranny pan, you will have to drop the entire pan. start by loosening the bolts all the way on one side and halfway on the other so the pan will drop further on one side to drain the fluid. This will not get all the fluid out of the car, the only way to get all the fluid is to flush the tranny at a shop.

Posted on Sep 05, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 582 Answers

IF THIS IS A FRONT WHEEL DRIVE THE PAN WILL NEED TO BE REMOVED TO DRAIN THEY DON'T PUT PLUGS IN THE PANS ANY MORE

Posted on Sep 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the transmission gasket on a 1988 chevy Silverado


Changing the transmission gasket on any car..
You need to drain the transmission fluid - if you get under the car you will see the transmission pan drain plug.

Drain the transmission fluid and then remove the small bolts that hold the fluid pan to the transmission body. You may need a blunt screw driver to break the seal/lever the pan off. Be careful when levering as you don't want to damage the mating surface of the fluid pan.

With the fluid pan removed use a blunt screwdriver to scrape off the old gasket from the pan and the transmission body. Apply a thin smear of sealant to the pan and place the new gasket onto it - line up the holes in the gasket with the bolt holes in the pan.

Lift the pan up against the transmission body and put the bolts in finger tight to hold it into place, then tighten with a socket to pull the pan tight against the transmission body.

To refill the transmission with fresh fluid (don't use the old fluid) have a look on the side of the transmission itself. There will be a filler plug that needs to be unscrewed. Alternatively, you can rig up a funnel/tube and fill the transmission via the transmission dipstick tube. This method takes longer but it tends not to be as messy as filling the transmission via the filler plug.

However, before you start any work on the transmission gasket check that it is actually that gasket at fault. Fluid above/in front the transmission pan can point towards a leaking torque converter.

May 05, 2016 | Cars & Trucks

2 Answers

Change transmission oil


Hi Peter, If your Camry has an automatic transmission, for normal driving the auto fluid should be changed every 40,000km, there should be a drain plug on the transmission pan that takes a 10mm hex drive or 17mm socket to undo. You have two choices after driving the car onto ramps or jacking up and supporting on jack stands so you can safely get under the car. 1 - You can loosen and remove the transmission drain plug to let the auto fluid drain out into a container (careful not to lose the sealing washer) refit and tighten the drain plug and washer again. Remove the auto transmission fluid level dip stick, using a suitable funnel pour about 2.5 litres of suitable new auto trans fluid back into the transmission via the dipstick tube (I believe they take dexron 2 of 3 type fluid). Start the car and move it onto a level surface. With the engine running, handbrake on and brake pedal applied, shift the transmission from park through every gear selection slowly into 1st gear, then back to park. Leave engine running. Wipe the dip stick & insert it back into the dip stick tube fully, remove and check where the fluid level mark is on the end of the dipstick. If the fluid level indicates low or does not show at all, add 100ml of additional fluid and recheck the level till the fluid reaches the full mark on the dipstick. 2 - The second option is everything in the first option but includes replacement of the transmission filter and pan gasket. I would only do this if the car had travelled high km or the pan gasket was leaking. At the point where you've drained the old fluid into a container and refitted the drain plug and washer, remove all the transmission pan bolts and the transmission pan. If you have the time to let the fluid drain overnight prior to removing the pan it's a good idea because once the pan is removed, fluid will continue to drip from the transmission. You'll need to remove the old pan gasket, some may be stuck to the pan and or transmission, a razor blade type gasket scraper can be good for this but be careful not to scratch either surface when cleaning off the old gasket. Remove the bolts/nuts that hold the transmission filter onto the bottom of the transmission. Careful caus more fluid may drain out of the transmission or filter once removed. Fit the new filter and filter tube gasket & bolts/nuts, careful not to over tighten. Fit new pan gasket, pan and bolts. Continue with fluid filling procedure from option 1. I would suggest you only use option one and remember to double check the drain plug is tight. Also, remember to dispose of the old fluid correctly. Cheers

Nov 30, 2013 | 1993 Toyota Camry V6

1 Answer

How to change transmission oil in 2000 Pontiac grand am


You have two choices, you can either take it to a shop and have it power flushed, recommended because this gets rid of all the fluid and replaces it with new fluid. The second is to drop the transmission pan, most cars don't have a drain plug for transmission fluid, so you would need to take out all the bolts holding the transmission pan out slowly letting the fluid drain as you bring the pan down. After you have the pan off I would go ahead and change the transmission filter, it is just above the pan inside the transmission. Place the pan back onto the transmission and fill with fluid, about 6-8 quarts.

Oct 23, 2013 | 2004 Pontiac Grand Am

1 Answer

Where is transmission filter located in 2001 mitsubishi diamante located and how do i change it?


transmission filter in the bottom of transmission bolted to valve body.you need a large drain pan.place drain plug under transmission oil pan.remove transmission oil pan drain plug.let all transmission fluid drain out then screw back drain plug in oil pan.then you need to remove transmission oil pan then remove filter and replace pan gasket also.make sure you have right amount transmission fluid on hand.buy extra because if you short of fluid you cant drive car if fluid level too low.make sure you get the right amount fluid.torque pan bolts to 96 inch pounds.

Nov 10, 2011 | 2001 Mitsubishi Diamante

3 Answers

Need to change transmission fluid, PLEASE assist. is there a drain plug or does it need to be sucked out with high power equipment?


While some vehicles are equipped with a transmission drain plug, most are not. The ones that are not equipped require you to drop the transmission pan to drain the oil, which is a good idea anyway because there is a filter inside the pan which should be changed when you change the fluid. Look under your car and locate the transmission pan. If it has a plug it will usually be located on the back side of the pan. If it does not have a plug, the easiest way to drain the pan is to remove the screws from all but one side of the pan. When you have screws left in only one side, steadily loosen the remaining screws a few turns at a time allowing to pan to tilt slowly downward releasing the fluid steadily and avoiding a big mess. While you have the pan off, be sure to replace that transmission fluid filter and pan gasket. They usually come in a set. Hope this helps you out. Have a good day!

Jun 07, 2011 | 2006 Kia Optima

2 Answers

Changing transmission fluid


Hello,

changing transmission fluid a messy job because there's no drain plug to change the fluid, but you can do it yourself if you're so inclined. To change the fluid, you have to get under your vehicle and remove the pan from the bottom of the transmission.
When you loosen the pan, fluid will start to dribble out in all directions so you need a fairly large catch pan. You should also know that removing the pan doesn't drain all of the old fluid out of the transmission. Approximately a third of the old fluid will still be in the torque converter. There's no drain plug on the converter so you're really only doing a partial fluid change. Even so, a partial fluid change is better than no fluid change at all.
A typical fluid change will require anywhere from 3 to 6 quarts of ATF depending on the application, a new filter and a pan gasket (or RTV sealer) for the transmission pan. The pan must be thoroughly cleaned prior to reinstallation. This includes wiping all fluid residue from the inside of the pan and scraping all traces of the old gasket from the pan's sealing surface. Don't forget to clean the mounting flange on the transmission, too.
When the new filter is installed, be sure it is mounted in the exact same position as the original and that any O-rings or other gaskets have been properly positioned prior to tightening the bolts. Then tighten the bolts to the manufacturer's recommended specs.
When refilling the transmission with fresh fluid, be careful not to allow any dirt or debris to enter the dipstick tube. Using a long-neck funnel with a built-in screen is recommended.
CAUTION: Do not overfill the transmission. Too much fluid can cause the fluid to foam, which in turn can lead to erratic shifting, oil starvation and transmission damage. Too much fluid may also force ATF to leak past the transmission seals.
Add half a quart at a time until the dipstick shows full. The transmission really isn't full yet because the dipstick should be checked when the fluid is hot, and the engine is idling with the gear selector in Park. So start the engine, drive the vehicle around the block, then recheck the fluid level while the engine is idling and add fluid as needed until the dipstick reads full.

Take care and good luck

Oct 26, 2010 | Toyota MR2 Cars & Trucks

1 Answer

Is the Transmission sealed, can not change the filter and fluid? Where is the radiator, is it also sealed, can water only be put in the overflow?


The transmission is not sealed in the v8 I looked up. It's bolted together. prev.gif next.gif Fluid Pan Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section
  2. Raise and support the vehicle
  3. Place a drain pan under the transmission fluid pan
  4. Remove or disconnect the following:
    • Drain plug and drain the fluid
    • Shifter cable bracket NOTE: The transmission fluid pan gasket is reusable, clean and inspect for damage; if not damaged, the gasket should be reused.
    • Fluid pan and gasket
    • Transmission fluid filter
    • Clean and inspect the transmission fluid pan and magnet
    • Converter housing access plug
    • Converter drain plug
To Install:
NOTE: A new converter drain plug must be used to prevent leakage.
  1. Install or connect the following:
    • Install the converter drain plug. Torque to 89 in-lbs (10 Nm)
    • Install the converter housing access plug
  2. Lubricate the seals and install the transmission fluid filter. Torque the bolts to 89 in-lbs (10 Nm)
  3. Install the oil pan magnet in the transmission fluid pan NOTE: The transmission fluid pan gasket is reusable, clean and inspect for damage; if not damaged, the gasket should be reused.
  4. Install the transmission fluid pan and gasket and loosely install the screws.
  5. Using a crisscross sequence, torque the screws to 8 ft-lbs (11 Nm)
  6. Install the shifter cable bracket. Torque bolts to 18 ft-lbs (25 Nm)
  7. Install the drain plug. Torque to 19 ft-lbs (26 Nm) NOTE: It will be necessary to hold the drain plug (larger plug) with a wrench when removing the fluid level indicator plug.
    NOTE: Use 3/16 inch Allen key to remove the fluid level indicator plug. Remove the fluid level indicator plug.
  8. Verify the transmission fluid level
prev.gif next.gif

Jul 21, 2010 | 2001 Lincoln LS

1 Answer

Where is the drain plug located on a Volvo 2000


There no tranny drain plug, you must drop the pan to change the fluid and filter. Standard fluid is fne. I believe Dextron3 but double check with the autoparts store (tell them you have a volvo) and they can lookup the correct type of ATF.

Dec 04, 2009 | 2000 Volvo S40

2 Answers

2003 Dodge Stratus


no drain plug, no car or truck has had a drain plug for decades, reason? they want the filter changed with the fluid, so they make you pull the trans pan to drain the fluid, one very messy job.

Feb 12, 2009 | 2003 Dodge Stratus

1 Answer

Where is transmission drain plug 2001 FRD Explorer Sport


2001 Ford Explorer,depending on the engine option,will have either a 4R70W or 5R55E model transmission.Neither trans has a drain or fill plug in the pan or case.Changing the fluid is achieved either by removing all the pan bolts,removing the pan and fluid,then reinstalling and adding fluid through the filler tube,or by a shop that has a total flush machine that usually hooks into the cooler lines.I also change the filter on both transmissions as part of the fluid service.The 4R70W trans has a gasket that is reuseable for the life of the vehicle.The 5R55E pan requires a new gasket if dropping the pan.

Jul 17, 2008 | 2001 Ford Explorer Sport

Not finding what you are looking for?
1994 Honda Accord Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...