Question about Dodge Daytona

1 Answer

Engine will not start or run,has fuel pressure.and spark

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 986 Answers

You have lost your compression, need to check compression to make for sure,Your belt may have broke ,does it have a strange sound when you turn it over?

Posted on Sep 04, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: chrysler 3.3 vin r v6 mini van, starts then dies

Charlie. You have replaced the ECM on your van?.
Kedwin,, Your problem is, the computer on that 3.3 L.
Need to be programed with the VIN nember of your car.
The Antitheft System will disable the injectors due a incorrect VIN, Bucause the body computer is not recieve the correct pasword between 5 seconds after start up.
YOU have 2 options. 1 get a ALOHA Smith. some of they have the computer required to program ECMs.

The other option is: Get a new ECM from the dealer, They will program if ask for that.

NOTE:::::: Other way is . Put the body control module with the computer from the same car.

OK... I hope this work for yours.
If NOT letme know I can look for more information.
Thank you.

Posted on Jul 17, 2008

  • 2 Answers

SOURCE: 1992 Nissan 300ZX wont start

may wanna check the distributor could be outta whack (timing).

Posted on Feb 02, 2009

  • 6 Answers

SOURCE: 2000 toyota corolla ve engine will run at idle but

Install a new mass air flow meter i own this car ive had this issue with my own and several others

Posted on Jul 25, 2009

  • 15 Answers

SOURCE: 1986 toyota 4runner fuel delivery

check the fuel pressure regulator

Posted on Aug 23, 2009

  • 75 Answers

SOURCE: will not start. has fuel pressure and spark

Pretty sure both engines use chains instead of belts for timing, and if it did break the starter would spin quite quickly (noticeably faster than normal).

You may also want to check the compression for each cylinder, as well as the injectors (is there actually any fuel getting into the combustion chamber)

Hope some of this helps, if still an issue, does it sound like it's almost starting (turning over but not 'catching') or what?

Posted on Mar 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My truck doesn't start, I have pressure in the fuel lines and also spark


You may want to check the ignition module or the coil pack(s) for the spark issue. How are you checking for spark? The parts house has a very cheap tool to check for spark. It connects to the plug wire and the other end connects to the plug which does not have to be removed from the engine. Have someone turn the engine over and the clear window will register a light if you have spark. You may not have fuel pressure because you cannot start the truck. I am assuming with no spark you do not have a running engine, which may be causing a no fuel pressure issue. Do you have a mechanical fuel pump or an electric? Fuel pressure issue can be figured based on the last question I posed to you.Hopefully answering the questions I am asking and the directions towards spark issues will fix your problem.

Feb 13, 2015 | 1997 GMC Sierra

1 Answer

Engine flooding


Check the fuel pressure. The pressure regulator may have gone bad and is delivering too much pressure to the fuel rail, thereby flooding the engine.

Dec 07, 2013 | Cars & Trucks

1 Answer

Van cranks but will not start


Hi, if the engine cranks over normally when you attempt to start you car, but the engine does not start, the problem may be NO FUEL, NO SPARK or NO COMPRESSION. The engine needs adequate fuel pressure, a properly timed spark and normal compression to start.

To find why the engine won't start, remove the air inlet tube from the throttle body, push the throttle open and spray a small amount of aerosol starting fluid into the engine. Crank the engine. IF it has spark and compression but NO FUEL, it will start and run a few seconds before dying. If it does NOT start, it probably has NO SPARK.

Another method to check for spark is to pull a spark plug wire off of a spark plug (if it has plug wires, coil-on-plug ignitions do not) and place the open end of the plug wire near a metal surface on the engine. Have a helper crank the engine while you watch for a spark. DO NOT hold the wire while doing this as it can shock you. If you see a spark, the problem is not spark, but most likely NO FUEL or NO COMPRESSION. If you do not see a spark, the problem is in the IGNITION CIRCUIT.

Proper fuel pressure is critical for fuel injected engines to start and run. You should hear the fuel pump inside the fuel tank buzz for a couple of seconds when the ignition is turned on (no buzz means the pump is not running and the engine is not getting fuel). You can smell the tailpipe for gasoline vapors after cranking the engine. If you smell gas, the problem is likely not fuel but NO SPARK. You can also remove the plastic cap and press the schraeder valve test fitting on the fuel rail to see if there is any fuel pressure to the engine (not a very accurate test because fuel pressure must be at a certain level for the engine to start, for that you need a gauge). Even so, no fuel at the fuel rail would tell you fuel is not getting to the engine.

Dec 22, 2010 | 1996 Chrysler Town & Country

2 Answers

My vw will crank but will not start running i


Hi,


If the engine cranks over normally when you attempt to start you car, but the engine does not start, the problem may be NO FUEL, NO SPARK or NO COMPRESSION. The engine needs adequate fuel pressure, a properly timed spark and normal compression to start.


1) To find why the engine won't start, remove the air inlet tube from the throttle body, push the throttle open and spray a small amount of aerosol starting fluid into the engine. Crank the engine. If it has spark and compression but NO FUEL, it will start and run a few seconds before dying. If it does NOT start, it probably has NO SPARK.

2)Another method to check for spark is to pull a spark plug wire off of a spark plug (if it has plug wires, coil-on-plug ignitions do not) and place the open end of the plug wire near a metal surface on the engine. Have a helper crank the engine while you watch for a spark. DO NOT hold the wire while doing this as it can shock you. If you see a spark, the problem is not spark, but most likely NO FUEL or NO COMPRESSION. If you do not see a spark, the problem is in the IGNITION CIRCUIT.

3)Proper fuel pressure is critical for fuel injected engines to start and run. You should hear the fuel pump inside the fuel tank buzz for a couple of seconds when the ignition is turned on (no buzz means the pump is not running and the engine is not getting fuel). You can smell the tailpipe for gasoline vapors after cranking the engine. If you smell gas, the problem is likely not fuel but NO SPARK. You can also remove the plastic cap and press the Schroeder valve test fitting on the fuel rail to see if there is any fuel pressure to the engine (not a very accurate test because fuel pressure must be at a certain level for the engine to start, for that you need a gauge). Even so, no fuel at the fuel rail would tell you fuel is not getting to the engine.


Thank you!!

Jun 30, 2010 | 2001 Volkswagen Passat

1 Answer

Well my car wont start,tryed new battery still doesnt start. trey to pop the clutch didnt start. what could it be?


Hi,
The engine needs adequate fuel pressure, a properly timed spark and normal compression to start.


1) To find why the engine won't start, remove the air inlet tube from the throttle body, push the throttle open and spray a small amount of aerosol starting fluid into the engine. Crank the engine. If it has spark and compression but NO FUEL, it will start and run a few seconds before dying. If it does NOT start, it probably has NO SPARK.

2)Another method to check for spark is to pull a spark plug wire off of a spark plug (if it has plug wires, coil-on-plug ignitions do not) and place the open end of the plug wire near a metal surface on the engine. Have a helper crank the engine while you watch for a spark. DO NOT hold the wire while doing this as it can shock you. If you see a spark, the problem is not spark, but most likely NO FUEL or NO COMPRESSION. If you do not see a spark, the problem is in the IGNITION CIRCUIT.

3)Proper fuel pressure is critical for fuel injected engines to start and run. You should hear the fuel pump inside the fuel tank buzz for a couple of seconds when the ignition is turned on (no buzz means the pump is not running and the engine is not getting fuel). You can smell the tailpipe for gasoline vapors after cranking the engine. If you smell gas, the problem is likely not fuel but NO SPARK. You can also remove the plastic cap and press the schraeder valve test fitting on the fuel rail to see if there is any fuel pressure to the engine (not a very accurate test because fuel pressure must be at a certain level for the engine to start, for that you need a gauge). Even so, no fuel at the fuel rail would tell you fuel is not getting to the engine..
Thank you !!

Jun 01, 2010 | 1996 Nissan Maxima

1 Answer

My car wont start


Hi,


If the engine cranks over normally when you attempt to start you car, but the engine does not start, the problem may be NO FUEL, NO SPARK or NO COMPRESSION. The engine needs adequate fuel pressure, a properly timed spark and normal compression to start.


1) To find why the engine won't start, remove the air inlet tube from the throttle body, push the throttle open and spray a small amount of aerosol starting fluid into the engine. Crank the engine. If it has spark and compression but NO FUEL, it will start and run a few seconds before dying. If it does NOT start, it probably has NO SPARK.

2)Another method to check for spark is to pull a spark plug wire off of a spark plug (if it has plug wires, coil-on-plug ignitions do not) and place the open end of the plug wire near a metal surface on the engine. Have a helper crank the engine while you watch for a spark. DO NOT hold the wire while doing this as it can shock you. If you see a spark, the problem is not spark, but most likely NO FUEL or NO COMPRESSION. If you do not see a spark, the problem is in the IGNITION CIRCUIT.

3)Proper fuel pressure is critical for fuel injected engines to start and run. You should hear the fuel pump inside the fuel tank buzz for a couple of seconds when the ignition is turned on (no buzz means the pump is not running and the engine is not getting fuel). You can smell the tailpipe for gasoline vapors after cranking the engine. If you smell gas, the problem is likely not fuel but NO SPARK. You can also remove the plastic cap and press the schraeder valve test fitting on the fuel rail to see if there is any fuel pressure to the engine (not a very accurate test because fuel pressure must be at a certain level for the engine to start, for that you need a gauge). Even so, no fuel at the fuel rail would tell you fuel is not getting to the engine..



Thank you !!

May 30, 2010 | 2002 Cadillac Deville

1 Answer

Wont start, no spark anywhere


Check the spark, remove the fuse to the fuel pump and remove one of the spark plugs. Connect the plug to its lead and position it well away from the engine against the truck frame (do not hold it) and turn the engine over, check the spark. If no spark it most probably a faulty coil. Check the impedance of the spark plug leads and replace any that are much higher than the rest. My guess is that you have spark but no fuel, What?... OK this is what I think is wrong. Your pump is fine when at position 2 on the ignition switch however when you switch to position three to fire the engine the power to the fuel pump is momentarily disconnected. A leaking fuel pressure regulator or injector would drop the pressure in the fuel line and at the same time flood the engine making it impossible to start. Once you start the engine with ether the ignition is back to position 2 and the pump can make good any loss in pressure but because the intake mix is rich this will cause the engine to run rich too. A good fuel system is capable of delivering 40 - 50PSI of fuel pressure and when switched off up to 90% of this pressure should be maintained for about 5 minutes, if it cannot check out the fuel pressure regulator and injectors. The fuel pipe should be capable of filling a pint pot in about 15 seconds, if it cannot check out the fuel filter is clogged.
Hope the above gives you some pointers

May 21, 2010 | 1998 Chevrolet K3500

2 Answers

Car wont start


Hi,
If the engine cranks over normally when you attempt to start you car, but the engine does not start, the problem may be NO FUEL, NO SPARK or NO COMPRESSION. The engine needs adequate fuel pressure, a properly timed spark and normal compression to start.


1) To find why the engine won't start, remove the air inlet tube from the throttle body, push the throttle open and spray a small amount of aerosol starting fluid into the engine. Crank the engine. If it has spark and compression but NO FUEL, it will start and run a few seconds before dying. If it does NOT start, it probably has NO SPARK.

2)Another method to check for spark is to pull a spark plug wire off of a spark plug (if it has plug wires, coil-on-plug ignitions do not) and place the open end of the plug wire near a metal surface on the engine. Have a helper crank the engine while you watch for a spark. DO NOT hold the wire while doing this as it can shock you. If you see a spark, the problem is not spark, but most likely NO FUEL or NO COMPRESSION. If you do not see a spark, the problem is in the IGNITION CIRCUIT.

3)Proper fuel pressure is critical for fuel injected engines to start and run. You should hear the fuel pump inside the fuel tank buzz for a couple of seconds when the ignition is turned on (no buzz means the pump is not running and the engine is not getting fuel). You can smell the tailpipe for gasoline vapors after cranking the engine. If you smell gas, the problem is likely not fuel but NO SPARK. You can also remove the plastic cap and press the schraeder valve test fitting on the fuel rail to see if there is any fuel pressure to the engine (not a very accurate test because fuel pressure must be at a certain level for the engine to start, for that you need a gauge). Even so, no fuel at the fuel rail would tell you fuel is not getting to the engine..


Thank you !!

May 19, 2010 | 1989 Oldsmobile Delta 88

2 Answers

2001 expedition cranks but wont start


check your crankshaft position sensor

Mar 21, 2010 | 2000 Ford Expedition

1 Answer

Car wont start. Has spark, tried Carb Cleaner.


You may be weak on fuel pressure . even a couple of lbs low on a cold start will cause a no start.
Double check cold start cranking fuel pressure. If under 63-62 lbs you have problems.
one test is to give it a squirt of carb cleaner not starting fluid. If it starts then you have a fuel pressure problem.
Run the full fuel pressure test and post back pressures.
Here is the guide lines on testing.
Hard to start cold.
Check cold start fuel pressure.
Check engine running fuel pressure.
Check engine running on the road fuel pressure.
Then shut it off and watch for fast leak down.
Pinch off at rubber part or block off return line and check full pressure.
Later V6 and V8 gm engines should have 60-66 fuel pressure.
Cold start should be 64-65 lbs of pressure.
If you do not have full fuel pressure on a cold start the injectors will not squirt fuel.
Do not leave home without it.
Engine running should be 60-66 lbs pressure depending on engine load.
Full pressure with return pinched off should be 75-85 or more.
And if it has a fast leak down after shut off you have a leak.

The 75-85 is only a check on the capable full pressure of fuel pump.
If you can not find the rubber return line check full pressure by plugging return line or just or the true full pressure can be taken direct at the end fuel filter.
What are the pressure readings that you have done.
What are your cold start pressure readings?
Post back what you have. Good Luck

Dec 24, 2009 | 2002 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...