Question about 1994 Ford Ranger Supercab

1 Answer

Replaced the clutch master cylinder on 94 ranger

Replaced the clutch master cylinder due to the rod end breaking off the pedal pressure is weak and does not operate the clutch have bled the system no air comes out only fluid( 75- 80) pumps and refilling the resivor, what could i havenot done or need to do

Posted by on

  • Anonymous Mar 27, 2014

    fluid level good. but no clutch.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 164 Answers

Jack up the front end-way up. itll get the end of the master up high enough to allow the air trapped air to be bled

Posted on Sep 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Recently replaced clutch kit flywheel hydraulic slave cylinder on a 97 Chevy s10 4.3. Once the clutch system has been bled the clutch pedal pops off clutch master cylinder when pedal is hard. Any...


Not sure if I understand your question. Sounds like the push rod from the clutch master cylinder is pushing the cylinder off the firewall. If that is the case it could be that your rod wasnt fully engage into your cylinder make the rod to long and with enough pressure is popping the clip off the fire wall

Jan 12, 2015 | Cars & Trucks

1 Answer

How do you remove the clutch master cylinder on a 2003 ford ranger


First drain oil at slave cylinder, then remove pipe from master cylinder . disconnect clutch pedal push rod from cylinder , remove bolts holding cylinder to fire wall remove cylinder. wash off any fluid with water as it will damage paint .

May 16, 2014 | 2003 Ford Ranger Regular Cab

1 Answer

Grand am clutch pedal


try opening the bleed nipple on the slave cylinder so that you are not trying to press against the pressure plate when you push the rod into the master cylinder.

Dec 14, 2013 | Cars & Trucks

1 Answer

Clucth slips every nw and again.ive replace clucth master and slave cylinder and the hoses for the clutch and still get them same problem.i can fix it for like a week each time by releasing the pressure...


the push rod for the clutch master cylinder has no free play,could be the master cylinder is too tight to the bulkhead and it should have a spacer in the form of a shim/gasket ,or the distance between the end of the push rod to the master cylinder is adjustable or the pedal mechanism is adjustable

Jun 28, 2011 | Hyundai Accent Cars & Trucks

2 Answers

Clutch suddenly has no resistance and car won't shift gears. Fluids were low, have put fluid in the reservoir but still doesn't work. How do you bleed a clutch line?


on the transmission there is a slave cylinder that works like a brake cylinder, when you apply pressure to the clutch pedal a rod inside the vehicle under the dash pushes into a clutch master cylinder, (almost like a brake master cylinder without the reservoir, as the clutch master cylinder works off the brake master cylinders reservoir) the plunger in the clutch master cylinder applies fluid pressure to the slave cylinder,(located down on the trans near the clutch fork assembly) which projects a piston rod into the clutch fork dis-engaging the clutch. To bleed the clutch slave cylinder locate the bleeder screw on the slave cylinder,break loose so it loosens and tightens easily. Check fluid in brake master cylinder reservoir,fill if needed, while bleeder on the slave cyl is closed have a helper push clutch pedal to floor and back 7-8 times, (At first the clutch might stay at the floor, just pull it up by hand or foot and continue) after several pumps with no rest time push pedal to the floor and hold down with foot pressure, at this time loosen the bleeder on slave untill fluid leaks out, watch for air bubbles, close bleeder and repeat untill there is no sign of air bubbles, (make sure to check fluid in the brake master cylinder and keep fill as needed, do not let fluid get less than 1/2 empty as it might **** air and you will have to start over) If this does not bring clutch to operate then you need to check if slave cylinder is reachig its full extension of push rod or not. If it is not then you will have to replace the clutch master cyl or the clutch slave cyl or both as seals are bad and wont hold pressure. Or you need to inspect the clutch fork,the throw-out bearing, or the pressure plate fingers and clutch plate for failure or broken bent parts. I hope it turns out to be a easy fix on that clutching thing.

Jan 14, 2011 | 1995 Nissan Pickup

1 Answer

Where is clutch linkage located on 2004 olds alero ,. hard to put in reverse with out grinding. fluid is up and all other gears are great. thanks!!


sounds like a typical master cylinder problem, pressure is weak. easy to fix once you disconnect the actuator rod from the pedal. The plastic clip has four claws on it, might as wel just pry it off and let it break, the new master cylinder comes with a new one, snaps in easy and master bolts in with 2 bolts on the firewall. Bench bleed the cylinder, install and then bleed the master like you would with brakes.

Nov 07, 2009 | 2004 Oldsmobile Alero

2 Answers

1993 toyota paseo. When i depress the clutch theres no pressure


Your clutch hydraulic system is compromised. Look under the dash, where the clutch pedal has a rod going thru the firewall. If it is damp with oily fluid, your clutch Master Cylinder is leaking. Also, on the side of the transaxle, there is another cylinder, the clutch Slave Cylinder. It can be leaking, also. In any case, with a condition such as yours, I would recommend that you replace both the clutch master and slave cylinders. Over time, they can wear ionterally, and no develop the proper flui pressure to release the clutch.

Oct 19, 2009 | 1993 Toyota Paseo

6 Answers

My 1994 ford rangers clutch pedal just lost all pedal


There are two types of clutch actuators. (Mechanical & Hydtraulic)
A. For mechanical type,- Check the clutch cable as
this could be cut from wear and tear. This is easy
to replace. You can find this connected to the
pedal and the clutch lever near the transmission.
B.For hydraulic operated - Check the level of the
hydraulic oil at the cylinder of the hydraulic
actuator under the hood. This actuator is
directly connected to the pushrod driven by the
pedal. If the actuator is leaking, you have buy
a repair kit (Hyraulic clutch repair kit for Ford
Ranger 1994 MOdel.) These items must be
repaired to activate your pedal.

Oct 14, 2009 | 1994 Ford Ranger Supercab

1 Answer

I have A 1998 FORD RANGER EXT. CAB W/ 6 CYL.- 4.0 RECENTLY LOST PEDAL ON MY CLUTCH. REPLACED MASTER CYLINDER, SLAVE CYLINDER, AND THE CLUTCH PACK, HAVE FLUID THROUGH BLEEDER VALVE ON THE SLAVE BUT CAN NOT...


Take the top off the master cyl and slowly very slow push in on the clutch and watch for any bubbles comming up.Replace the top and pump pressure and bleed at the master direct by using the lines for bleeders.

Aug 13, 2009 | 1998 Ford Ranger SuperCab

1 Answer

2003 ford ranger clutch all of sudden just started going all the way to the floor with little resistance but will work if you pump it 3 or 4 times checked and has fluid in reservoir


You have seal bypass on either the master cylinder or slave cylinder, the fact that you can pump the pedal and get a bit of pressure back leads me to think it is the master cylinder.
The quickest way to check is pull aside the boot that sits on the end of the cylinder and around the push rod, if you see fluid inside the boot then obviously that cylinders seals are gone.
I still think your problem is in the master cylinder, if it was the slave all the pumping in the world would net get pedal pressure back like that, the fluid would just leak past the piston seal and drain out.

Aug 24, 2008 | 2000 Ford Focus

Not finding what you are looking for?
1994 Ford Ranger Supercab Logo

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...