Question about 1994 Audi 90

Open Question

Lost ignition key.

I need to know how to remove the interior door panel to get the door lock out to get a new key made?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I lost keys to 77 dodge.if i take the door lock off and take it to a lock Smith Wood it work for the ignition? Key is the same.and if so how do i remove it?


.You need to disassemble the inside door panel. It is held to the door with a couple of screws and several clips on the back side of the panel. The lock is attached to the door with a horseshoe type clip that will slide away from the lock cylinder from inside the door.There will be a rod attached to the cylinder with a metal clip that you will also have to disconnect. It may be easier/cheaper to change the ignition cylinder and have new keys ( supplied with cylinder ) than go to lock smith

Apr 11, 2015 | Dodge Cars & Trucks

1 Answer

Thank you for your response , been going crazy here...got panel off enough to put hand in but don't know where to pull to unlock door.



Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

  1. Visually inspect the following:
    Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
  2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible
  1. Turn ignition key to position II.
  2. Motor door glass to fully raised position.
  3. Turn ignition key to position O.
  4. Disconnect the negative battery cable.
  5. Remove door casing for access.
  6. Remove door water shedder.
  7. Position PVC secondary water shedder for access.
  8. Slacken and remove the door glass rear runner lower securing screws.
  9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
  10. Slacken and remove the upper securing screw and move the runner away from the glass.
  11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
  12. Slacken and remove the three latch assembly securing screws and position latch for access.
  13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
  14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
  15. Remove lock motor assembly from door.
  16. To install, reverse removal procedure.

    zjlimited_378.jpg

    Fig. Removing door lock actuator


Sedan
  1. Remove the door window glass
  2. Detach the interior door handle.
  3. Detach the actuator remote cable from the interior door handle.
  4. Remove the interior door handle.
  5. Detach the door window glass run.
  6. Remove the exterior door handle retaining screws.
  7. Remove the front door actuator retaining screws.
  8. Reposition the front door actuator and exterior handle.
  9. Remove the front door actuator and exterior handle.
  10. Disconnect the front door actuator remote cable.
  11. Detach the door lock cylinder connecting rod (1).
  12. Detach the exterior door handle connecting rod (2).
  13. Remove the front door actuator (3).
  14. To install, reverse removal procedure.

    zjlimited_379.jpg

    Fig. Removing door lock motor-Sedan



Hope this helps.

Dec 31, 2010 | 2002 Jaguar X-Type

1 Answer

I have the wrong key broken off in my toyota matrix..Is this expensive to fix


If it is in a door lock, the interior door panel can be removed and the lock cylinder can then be taken out and taken to a locksmith. You can count on at least one hour of labor for removal and installation plus the locksmith fee.

If it is in the ignition, it is trickier because in general you need to be able to turn the ignition key to the ACC position in order to remove the lock cylinder. If this cannot be done, then it may be necessary to destroy/drill out the lock cylinder in order to remove it. Then you will have to pay to purchase a new lock cylinder and have it re-keyed. This would cost you more than the door lock repair, for sure.

Mar 16, 2010 | 2006 Ford Focus

1 Answer

Program remote


The horn chirp can be disable by pressing the lock and unlock buttons simultaneously until the hazard lights flash, and no enable press the lock and unlock until the horn chirp.
To reprogram (enter new ID) key fob (keyless remote controller) follow the steps.
1. Close all doors and lock all doors
2. Insert and remove the key from the ignition key cylinder more than six times within 10 seconds. (The hazard warning lamp will then flash.) NOTE: Key should be withdrawn from ignition key cylinder completely each time.
NOTE: Do not rush the insertion/removal key cycling process. The side marker/tail/license lamps and interior illumination will flash twice when this step is accurately completed.
3. Insert key on ignition key cylinder and turn ignition key switch to "AAC" position At this time, the new ID code is entered and original (previous) ID codes are erase.
4. Press any button on the new remote controller once. (The hazard warning lamp will then flash)
NOTE: Do not press the button more than one time in the above step. If the button is pressed more than one time, the programming procedure will not be successful. The side marker/tail/license lamps and interior illumination will flash twice when this step is accurately completed and programming is successful.
If there is only one remote controller skip step 5.
5. Additional ID code entry Release the door lock, then lock again with door lock/unlock switch (In power window main switch)
6. Remove key from ignition
7. Unlock driver side door, open driver side door and then close the door. (END)

Feb 20, 2010 | 2001 Nissan Pathfinder

1 Answer

96 Toyota Camry keys are not working to open locked door from outside. First the passenger side and now the driver's side door.


Try spraying some silicon lubricant into the keyhole and slide the key in and out a few times.

If this does not work you may have to remove the interior door panel and trouble shoot the lock mechanism.

It's also possible the lock cylinders are worn and need to be rebuilt. This can be done by a qualified locksmith (look for a AAA certified locksmith). Or you can order new lock cylinders and get them re-keyed to match your ignition key.

Dec 16, 2009 | 1996 Toyota Camry

2 Answers

My Bf has a 1999 saturn SL1 and he lost the key to it... he took to to the car dealiship showed them his papers and they gave him a new key... but the new key does not work. it works on the door and the...


Below are instructions for changing the lock cylinder as well as a few diagrams. Best of luck.
Greg
  1. Disconnect the negative battery cable.
  2. Remove the lock cylinder bezel from the steering column shroud by carefully prying with a thin bladed screwdriver.
  3. Remove the shroud fasteners and remove the steering column upper and lower shroud panels.
  4. Insert the key into the ignition lock cylinder and rotate to the RUN position. Then rotate the ignition cylinder back to the ACC position.
  5. Depress the locking button on the side of ignition module assembly with a thin pick-type tool. Slide the lock cylinder assembly from the ignition module.





3321ca5.gif5b3b81a.gif INSTALLATION:
  1. Insert the key into the ignition lock cylinder and install into the ignition module.
  2. Install the steering column upper and lower shroud panels and the shroud fasteners.
  3. Install the lock cylinder bezel.

Reconnect the negative battery cable.

Jul 30, 2009 | 1999 Saturn SL

1 Answer

Lost keys


Why are you taking out the old one. Check with any good locksmith. If your door key fits the ignition, you can easily remove a door lock cylinder and the locksmith can make you a new key!!! I'm pretty sure to remove your lock you need to turn it with the key in it (but you don't have one)

Jan 03, 2009 | 1983 Jeep CJ7

1 Answer

1997 venture keyless remote programming


SYSTEM OPERATION

System warning lamp located on top of the instrument panel
Press UNLOCK button once , turns on interior lamps and deactivates alarm (if fitted)
Press UNLOCK button twice w/in 5 seconds unlocks all doors, turns on interior lamp and deactivates alarm (if fitted)
To activate alarm system (if fitted):
Switch ignition OFF
Open driver's door
Press Lock button on remote
Close Driver door
warning lamp will flash when system is activated
Press remote power sliding door button will open sliding door (if fitted) only if unlocked first
Pressing remote panic button:
*Sounds horn intermittently
*Flashes exterior lamps
*Turns on interior lamps
**Pressing panic for the second time OR switching ignition ON deactivates alarm.


PROGRAMMING
Remobe key from ignition switch
Remove the "BCM PRGRM" fuse, from the fuse box
Close all doors
Turn ignition switch to the ACC position
With in 1 SECOND , turn the ignition switch to OFF then back to 'ACC'
(really, with in one second)
Open and close the driver's door. A chime will sound, indicating programming mode activated
Press and HOLD LOCK and UNLOCK SIMULTANEOUSLY untill a chime sounds 2 times ( about 15 seconds)
Repeat this exact procedure for all remotes to be programmed
Remove key from ignition
Refit 'BCM PRGRM' fuse.

4 REMOTES MAXIMUM CAN BE PROGRAMMED

Aug 24, 2008 | 2000 Chevrolet Venture

Not finding what you are looking for?
1994 Audi 90 Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14184 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...