Question about 1992 Chevrolet S-10

1 Answer

Changing the oil sensor on 1992 4.3L S-10

I am trying to change the oil sensor on my 1992 S-10 4.3L. I am running into a problem with how to remove the sensor. It is in a place where I cannot get a wrench or pliers with enough leverage to loosen it. Is there some special tool or trick?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Chevrolet Expert
  • 332 Answers

Actually there is a tool it looks like a box end wrench but has a spot open on the box end there is another tool that looks like a deep wall socket and it has one side open hope this helped

Posted on Sep 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

At 28,066 dealer oil change. At 28,778 dealer flushed engine to remove sludge build up and changed oil. At 30,835 miles inspection, dealer flushed engine to clean out sludge and changed oil. At 34,630...


First dealer was NOT doing you any justice. Next oil change run a can of GUNK engine flush let idle 5-10 mins then change Oil & Filter and use a good oil like Castrol or Valvoline 10w-30. You won't have "supposed" sludge build up.

Mar 02, 2011 | 2000 Chrysler Town & Country

2 Answers

Hi, I have a 2002 nissan sentra automatic 1.8. I bought it used when the mileage was 96,000. Now, it is 100,000. I read somewhere that I need to change the timing belt (if the car has it) when it reaches...


timing chain runs in oil and when it wears it clatters ,often its the adjuster needs changing only ,while its running ok leave well alone and do not look for problems that are not their ,change the oil every 6000miles with a oil filter every third oil change use the cheapest oil you can buy from a supermarket i prefer a diesel/petrol type oil of say 10/40 or 20/50 ,this will keep the inside of the engine clean and then i think it will run for ever without any problems .well i was trying to scan my alldata book on how to reset the service light but it seems to have locked up and i thionk i will need to restart computer ,did you get the four wires the right way around when you chande the O2 sensor

Nov 02, 2010 | 2002 Nissan Sentra

2 Answers

Oil pressure drops after worm up


let vehicle reach normal operating temp. remove oil pressure sensor replace with manual oil press. gauge run engine and monitor oil pressure go from there dependent upon findings

Mar 17, 2010 | 2000 Jeep Grand Cherokee

2 Answers

1)How difficult is it to change crank case position senor for 2002 Olds Aurora 4.0 engine? Eng check lite on for that reason. 2) Losing oil only when engine running. Can smell in passenger compartment when...


2002 Oldsmobile Aurora V8-4.0 Replace Crankshaft (Sensors) A and B This car has 2 sensors 1- Raise and support car. 2- Remove the oil filter adaptor. 3- Remove crankshaft sensor electrical connector. For specific CKP sensor identification. 4- Remove the crankshaft sensor retaining bolt. 5-Remove the crankshaft sensor. NOTE= Inspect the CS sensor o-ring for wear or damage, if problem is found replace it also. 6- Lube O-ring with clean engine oil. 7- Install theretaining bolt TIGHTEN to 10 N.m (89lb in) 8-Install the CS sensor electrical connecror. 9- Install oil filtor adaptor. 10- Lower car. 11- Operate engine and inspect Cs sensor for oil leaks 12Perform the CKP system variation learn procedure.

Feb 10, 2010 | 2002 Oldsmobile Aurora

2 Answers

It crancks but dont start it has gasoline, mybfrien changed the oil 1 week ago 10-40 is the kind that he used


The type of oil will not affect the cars ability to start, If the car ran fine before the oil change I expect a wire from a sensor or coil has been disturbed. I'd check under the hood for any loose or removed connections.
I hope this may have helped,
Tom

Oct 15, 2009 | 1992 Geo Metro

2 Answers

1987 chevy S10 engine idle problem


relace the throtle air idle valve.The temp switch will allso cause this problem.

Jul 19, 2009 | 1987 Chevrolet S-10 Pickup

2 Answers

1987 chevy engine problem


you have to reset base idle see manual at library for procedure

Jul 19, 2009 | 1987 Chevrolet S-10 Pickup

1 Answer

Oil pressure gauge shows low / high / middle changed sensor did


Hello mb4494: My name is Roger and I will help you. If by changing the oil pressure sending unit the problem did not change. I would perform a oil pressure test. This is done by removing the oil pressure sensor and inserting a oil pressure gauge. This can be done by yourself or by a repair shop. This needs to be done on a cold engine. Start the engine and observe the oil pressure cold.as the engine warms up observe the pressure. The pressure will drop off as the engine warms up.Should the oil pressure drop below 10 to 12 PSI. then you have internal engine trouble. More then likely a bearing problem. Try dropping the truck into gear and see what the pressure drops off to. Again if the pressure drops below 10 to 12 PSI. you have a problem. I would also check to make sure you have the correct oil switch. a truck with a oil light uses a oil pressure switch. with a gauge you would use a oil pressure sending unit. Sorry for the long reply but want to make sure you check the pressure correctly. Please rate the quality of the answer as this is how we know the answer was correct. Thank You for using Fix Ya. Roger

Jun 16, 2009 | 2004 Ford F150

4 Answers

1991 chev blazer S-10 4.3 engine appears to be starved for fuel


oyu are going to think iam crazy check the converter go to the back of truck see how munch air is comeing out i have 2 and they done the same thing replaced converter runs fine

Feb 17, 2009 | 1991 Chevrolet S-10 Blazer

Not finding what you are looking for?
1992 Chevrolet S-10 Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6910 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...