Question about 1995 Ford Taurus

1 Answer

I have a 1995 Ford Taurus SHO 3.0 liters. I

I have a 1995 Ford Taurus SHO 3.0 liters. I have replaced the crankshaft sensor, the ignition control module, and the coil pack yet the spark plugs are not getting any fire and the car will not start. Any suggestions?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 298 Answers

Hi did you do a continuity check check if there's a wire shorted or open you'll need a volt meter check if the wires on the crank sensor going to the control module and also the one from the coil to the module there has to be a shorted or open wire check this and get back to me good luck

Posted on Sep 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Crank shaft sensor location on a 1996 ford taurus


on the 3.4 SHO the sensor is mounted in the front right side of the block
it reads off the gear behind the crankshaft pulley

on the 3.0 4v its similar to 3.4 but just mounted front left side

on the 3.0 2v its mounted against the front of the block reading off the crankshaft pulley

Aug 28, 2016 | 1996 Ford Taurus

3 Answers

Where is the crank sensor on a 1994 ford taurus gl


What engine? 3.0 DOHC 3.0 OHV 3.8 liter

Apr 10, 2013 | 1994 Ford Taurus

2 Answers

97' TAURUS SHO 3.4 LITER HAVE THE CODE PO102 NEED TEST PROCEDURE TO FIX


inspect Mass air sensor, clean with electrical cleaner and test. should read around 3 on scanner and jump to 15-20 upon accelaration if not replace.

Apr 09, 2010 | 1997 Ford Taurus

1 Answer

3.2 liter yamaha engine manual IAC valve How do I replace the IAC valve on this engine? Steps? I just bought a new one and I need to get it replaced. FORD 1994 Taurus SHO 3.2 liter engine YAMAHA


may just need cleaning with carb cleaner.

here is 1996, oldest I have:

Section 03-14: Engine Controls, Electronic 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Idle Air Control (IAC) Valve Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Disconnect the engine control sensor wiring (12A581) from the idle air control valve (IAC valve) (9F715) at the idle air control valve electrical connector.
  1. Remove the two idle air control valve retaining bolts.
  1. Remove the idle air control valve and idle air control valve gasket.
Installation
  1. NOTE: If scraping is necessary, be careful not to damage idle air control valve gasket surfaces, or drop material into intake manifold (9424) or throttle body (9E926) (depending upon application).

    Clean idle air control valve gasket mating surfaces.
  1. To install idle air control valve, reverse Removal procedure.
  1. Tighten the idle air control valve retaining bolts to 8-12 Nm (71-106 lb-in).
33b4417.gif

Jan 14, 2010 | 1994 Ford Taurus

2 Answers

1995 Ford Taurus SHO Where is knock sensor located? Thanks


Under hood, passenger side, lower engine area, above engine mount, mounted in engine block .This what it looks like hope this helps d52f852.jpg

Nov 20, 2009 | 1995 Ford Taurus

2 Answers

1995 Ford Taurus Sho 3.2 check engine light blink 3 3 1 3 3


Code 33 is EGR opening not detected, this is caused by a plugged EGR exhaust passage in the upper intake manifold, this is a common SHO engine fault, the valve works but the engine does nothing that the computer can sense, since no gas flows, to verify this is the problem open the egr at idle, the engine should almost die, if nothing happens or only a tiny change in idle speed or quality the passages are plugged, if it does stall or get real rough the egr position sensor (usual code for sensor is 32) may be faulty or the valve is sticking. I was a ford dealer tech for 30 years and did quite a few of these, there is a TSB (technical service bulletin) about this problem

Oct 12, 2009 | 1995 Ford Taurus

1 Answer

Need to know what fires coil 1995 mercury sable both wires to coil have power when key is turned on car cranks no spark from coil new coil what gives the coil extra power to fire


what engine? 3.0L 2 Valve? 4 Valve?
3.4L SHO engine?

The PCM (engine computer) fires the coils, but it is never the cause of a problem. I suspect it is the crankshaft position sensor on the front of the engine by the crank pulley. easy to change.

Crankshaft Position Sensor The crankshaft position sensor (CKP sensor) (6C315) is a variable reluctance sensor triggered by a 36-minus-1 tooth trigger wheel located on the crankshaft pulley and damper. The signal generated from the crankshaft position sensor is called the crankshaft position (CKP) signal, which provides base timing and crankshaft speed (rpm) information to the ignition control module (ICM) (12K072). Base timing is set at 10±2 degrees before top dead center (BTDC) AND IS NOT ADJUSTABLE. The powertrain control module (PCM) (12A650) will use this information with the spark advance information to determine ignition coil (12029) turn on or turn off time.

Sep 15, 2009 | 1995 Mercury Sable

1 Answer

Where is the crank senser located on the engine of ford taurus


Crankshaft position sensor mounting 3.0L 2V engine

44f4d81.gif
Crankshaft position sensor mounting 3.0L 4V engine

ee7d7f9.gif
Crankshaft position sensor mounting 3.4L SHO engine

deb0eac.gif

Jul 12, 2009 | 1999 Ford Taurus

2 Answers

1995 Ford SHO


your best bet for a diagram is to ask for a suspension printout at your local dealership. Or take a look under any 86-95 Ford Taurus SLO, SHO, or Sable and they use the same design (the SHO just uses slightly different parts. Here is a link though for a SHO parts list with part numbers. Hope this helps.

http://members.bellatlantic.net/~rbruce/SHOParts.htm

Mar 12, 2009 | 1995 Ford Taurus

2 Answers

Engine dies 95 taurus


It is most likely the TFI ignition module, replace it, don't use anything but the FORD part, the aftermarket modules are very poor quality, I have done hundreds of TFI"s and know this for a fact.

Aug 06, 2008 | 1995 Ford Taurus

Not finding what you are looking for?
1995 Ford Taurus Logo

Related Topics:

548 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...