Question about 2004 Chrysler Pacifica

1 Answer

3rd brake light, 2005 pacifica

How do you replace it. It seems to be sealed off. Do I have to take molding off of the rear gate?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chrysler Master
  • 1,564 Answers

The plastic cover is snapped into place with small teeth. There are about 5-6 ofthem you can pry around the perimeter with a non-serrated butterknife. Then it should pop off. Take care not to scratch any of the defrost srtips glued to the window for they are all looped together and your rear defroster will no longer operate correctly.

Posted on Sep 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 chryaler Pacifica tail gate location


I have run into this problem and i found that the switch that operates alarm and inside light is bad, the switch is located on the latch, the latch may need to be removed to replace the switch. some dealers do not sell just the switch, i have run into this problem where switch is not replaceable the complete latch needs to be replaced.

Another problem i have run into is the wiring going into the hatch breaks, the wiring from bendine due to door opening and closing breaks a wire or two due to bending , locate wiring coming into rear hatch and check each wire,

Sep 03, 2012 | 2004 Chrysler Pacifica

1 Answer

My 2005 Pacifica has started leaking when it rains hard from the area right above where the airbag button is. The water leaks down to the floor by brake and accelerator pedals.


It sounds like a leak in the sun roof seals. Better fix it right away. I had the same in my Acura and let it go. Soon I had mold and headliner damage all over the ceiling.

Jun 27, 2011 | 2005 Chrysler Pacifica

1 Answer

The gear is getting stuck... i press on brakes and when car is in park it is hard to put on reverse.. the car runs great...


In all probability the brake sensor on the pedal is starting to work erratically. This sensor sends a signal to the shifter gate, and the gate will not open unless the brake pedal is depressed. I had it happen to me, and the only solution until i replaced the sensor was to hit the brake over and over until the stop light worked (You can check it while looking at the 3rd stop light in the rear view mirror). If the stop lights work, the shifter gate should allow the shifter to move out of park. This sensor/ switch is located about 3 inches above the brake pedal, and it is easily recognizable by the cable attached to it.

Aug 31, 2010 | 2002 Honda Accord

1 Answer

Rear seat wont fold down in pacifica 06


third brake light wont work it connected to a circuit board?

Nov 12, 2009 | 2005 Chrysler Pacifica

1 Answer

Is it easy to replace the rear turn signal and brake light bulbs on a 2005 Pacifica? Do you access the screws from the hatch?


You can access screws from hatch behind liner. there should be two screws for each lens. Bulbs and socket just turn and remove.

Aug 25, 2009 | 2005 Chrysler Pacifica

1 Answer

I can not see how to replace the tail light/brake lamp (passenger side)on my 2005 MPV. Can you help?


open the rear tail gate there should be a couple of screws on the inside near the rubber seal just remove them and the assbilme should pull ot and the bulb may be a twist lock and pull ot and remove the bulb

Mar 06, 2009 | 2005 Mazda MPV

1 Answer

How do I change the bulb 2004 infiniti high mount bake light?


Unfortunately, these are not very simple. If you have a factory high mount brake light-meaning not one in a spoiler, you have to remove the rear seats, the rear parcel shelf and then the 3rd brake light. the 3rd brake light I believe is an LED setup which get replaced as an assembly which inserts into the housing. If you need further guidance let me know.

Thanks,

Brian

Dec 10, 2008 | 2005 Infiniti G35

Not finding what you are looking for?
2004 Chrysler Pacifica Logo

385 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...