Question about 1991 Mitsubishi Mighty Max

Open Question

Rear wheel bearing replacement on a 1991 mighty max truck

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque for installing the crankshaft for the 2.4 mitymax motor?


Mitsubishi Mighty Max crankshaft bolt Questions & Answers ...

www.fixya.com > ... > crankshaft bolt > Cars & Trucks > Mitsubishi
Mitsubishi Mighty Max cars & trucks crankshaft bolt questions and answers. ...Torque specs for mighty max The head torque specs for 1991 mitsubishi mighty max 2.4 I ... 1989 mitsubishi 2.0 motor crankshaft was turned while timeing belt was off. ...how to install a clutch kit on my 1994 mitsubishi mighty max Disconnect the .

Oct 02, 2015 | Cars & Trucks

1 Answer

1991 Mitsubishi Mighty Max. Steering shakes badly went driving faster than 50 mph.


either the wheels want balancing or you have a ball joint problem...

Aug 25, 2010 | 1991 Mitsubishi Mighty Max

1 Answer

1991 MITSUBISHI MIGHTY MAX 2.4 CHECK ENGINE LIGHT COMES ON AND OFF AND WHEN IT DOES I CAN FEEL THE ENGINE CHANGE. I JUST REPLACED THE ALTENATOR AND THE MASS AIR FLOW SENSOR.


try the oxygen sensor. the heated one, when the heater burns out it causes problems. Its the one with 3 wires usually in the rear

Mar 23, 2010 | 1991 Mitsubishi Mighty Max

1 Answer

Put in distributor for 1991 mitsubishi mighty max


Please confirm which engine your truck has; 3.0 V6?

Thanks,
Tom

Feb 28, 2010 | 1991 Mitsubishi Mighty Max

1 Answer

Torque specs for mighty max


Per my Chilton's manual tehe bolts should be (cold engine) 65 to 72 FT. Pnds., the cam shaft bearing bolts should be 8x25 = 15 - 19 Ft pnds and the 8x65 should be 14 - 15 Ft Pnds.

The sequence is as follows for the (10 ) head bolts:

7 - 5 - 2 - 4 - 10

9 - 3 - 1 - 6 - 8

I hope this may help,
Tom

Oct 12, 2009 | 1991 Mitsubishi Mighty Max

1 Answer

I may need to replace the front wheel bearing. There is a squeeling sound coming from the front right side of the car.


Normally a squeeling noise coming from the front wheel area would be the front brake disk pads getting too low. Normally when wheel bearings start to fail the noise they produce is more consistant which a growl noise.

Jul 08, 2009 | 1993 Mitsubishi Mighty Max

2 Answers

Need the valve gap for 1991 mighty max


Does not have adjustable valves . It has hydrolic valve lasher's . they are spring loaded ( i believe ) . I just replaced them in mine . valve giude seal's where worn out causing it to smoke realy bad ( looked like a mosqito truck ) and the valves where ticking , due to the hydrolic valve lash adjuster's being worn out . They are about $ 8 - 10 buck's each at advance .

Mar 22, 2009 | 1991 Mitsubishi Mighty Max

1 Answer

Computer in 1991 mits pick up


I recently replaced the ECU in my 91 mighty max. If you remove the glove box you will see it on the right hand side.

Feb 28, 2009 | 1991 Mitsubishi Mighty Max

1 Answer

1991 mighty max


If it is 4X4 and you re not going far. Put the transfer case in neutral. If it is 2X4 standard transmission, put it in neutral. If it is an automatic transmission you need to remove the driveline.

Jul 10, 2008 | 1991 Mitsubishi Mighty Max

Not finding what you are looking for?
1991 Mitsubishi Mighty Max Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...