Question about 1988 Chevrolet S-10

1 Answer

Need to know what wires to use for the ignition switch on my s10

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,596 Answers

There are (RED HOT ALWAYS) Another RED (KEY ON HOT) Purple, ( START TRIGER)., Orange (To Accessories)

Posted on Sep 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a wiring diagram for a 2002 chevy s10 4 wheel drive 4.3 for the starter to the switch


If the truck cranks over you have voltage at the ignition switch ! From starter to switch , First off starter to what switch ,ignition ? There is a 175amp fuse that supply's battery voltage to the power distribution center - fuse box under the hood . On the lower right side of the radiator support, below the battery !

Sep 10, 2015 | Cars & Trucks

1 Answer

How do i add a new fuse cirquit to a 99 chevy s10


If there are any empty gaps in the primary fuse box use those to run your wires from box to fan. However you could simply tap into switched HD wire on ignition and use in-line fusing on the fan wire.

Oct 14, 2014 | 1999 Chevrolet S-10 Pickup

1 Answer

My s10 starts when cold as soon as warm up wont start i have change the fuel pump distrubutor fuel spider still the same problem the spark plugs full with gas do it have afuel relay that is stuck open if...


Sounds like the ignition switch is getting hot.Check the ignition switch wires for any melted wires or hot spots.If any of the wires look burnt or melted replace switch.

May 13, 2011 | 1994 Chevrolet S-10 Blazer

1 Answer

Now i replace the ignition cylinder but i steel kent starer on my chevrolet 1987 s10 pickup


check power on large yellow wire from ignition swith while turning key to start possition,this is the wire that powers the solenoid to starter.also may try tapping on starter with hammer while someone is trying to start.If starts while performing tap method you will need a starter. If no power to yellow wire at ign switch while starting will need electrical part of ignition.

Jun 16, 2009 | 1987 Chevrolet S-10 Pickup

1 Answer

Pass lockm system


To reset the pass lock system, turn key on for five minuets, then shut key off for five minuets. then restart normally. If the system resets for no reason you need to replace the anti theft module.

Oh leave the key's in the ignition switch when turning the key to the off position. I know that to replace the ignition lock and key at the dealer will be expensive. Your S10 is 9 years old and if you can find a lock smith who knows how to by pass the wire harness in the steering colum have him do that so you'll never have this problem again.
If you want to know how to by pass it your self, i'll send you an e mail on how to do it. Just can't post it here, never know who's reading eh.
Good luck and hope this helps.

May 22, 2009 | 2000 Oldsmobile Intrigue

1 Answer

Toggle switch attached to battery or starter


first of all i need to know if the vehicle will start without the toggle switch? if it does then you can just remove it if the vehicle will not start without turning the switch on you should know that the initial power is from this switch so mostly you have problem in the ignition switch and you have to repair or replace the ignition switch before yo disengage the toggle switch.

Jan 14, 2009 | 1987 Chevrolet S-10 Pickup

1 Answer

Buzzer for ignition switch operates at will now


sounds like a lose wire or the wiring is all back up

Dec 18, 2008 | 1991 Chevrolet S-10 Blazer

1 Answer

Rplacing the ignition switch


there is a safety switch that prevents the ignition from being turned off and removed while in gear. try putting in nuetral and removing the key. if it does then it is a problem with the shifter and not the ignition.

Nov 30, 2008 | 1997 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...