Question about 2002 Pontiac Montana

Open Question

Passenger side power control switch does not work

We replaced the motor and the controls worked but the window would go up and down so fast! Then it stopped working again AND the driver side power control master switch went out. Tested the wires and they're getting power. Tested the drivers side master control switch and it gets power and lit up when tested. Passenger side does not work so we know we have to replace that. How do I solve this problem for the driver side master control switch? Checked the fuse and it was fine but we're going to check ALL fuses. Are there any other fuses that effect the windows that we should know about?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Right side windows does not work from drivers door or pass.and rear door 2007 Silverado new body


What's with the 1994 C/K 2500 above an 2007 Silverado ? 07 on 94 frame ? New body have all the 07 electronics ?
Power Window System Controls (RPO A31/AN3/DL3)
The power window system will operate anytime the Retained Accessory Power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The driver master control switches are integrated into the DDS. When a power window switch is activated in the up or down positions the DDS supplies power and ground to the window motor control circuits to drive the window motor in the required direction. Prior to activating a power window motor the DDS will supply the control circuit with a low current bias voltage in order to determine that a short to ground condition does not exist and during window motor operation the DDS continues to monitor the motor current to verify proper window motor operation.
The DDS controls the passenger window through a GMLAN message to the PDS. When a power window switch is activated in the up or down positions the PDS supplies power and ground to the window motor control circuits to drive the window motor in the required direction. Prior to activating a power window motor the PDS will supply the control circuit with a low current bias voltage in order to determine that a short to ground condition does not exist, and during window motor operation the PDS continues to monitor the motor current to verify proper window motor operation. (Scan tool support is available for this system)
Do you know what GMLAN is ? serial data communication network
How to Diagnose Controller Area Network CAN GMLAN is general motors C.A.N
Passenger Power Window Inoperative
  1. Ignition OFF, disconnect the C1 harness connector at the PDS.
  2. Test for less than 1 ohm between the ground circuit terminal 6 and ground.
  3. ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

  4. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 2 and ground.
  5. ?‡'
    If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.

  6. Ignition OFF, reconnect the harness connector at the PDS.
  7. Ignition ON, observe the scan tool Passenger Window Switch parameters while using the passenger power window switch. The reading should change between Off/Up/Down/Express Down.
  8. ?‡'
    If the parameter does not change, replace the PDS.

  9. Ignition OFF, disconnect the harness connector at the passenger window motor.
  10. Connect a test lamp between control circuit terminal A and control circuit terminal B.
  11. Ignition ON, command the passenger window UP and DOWN by using the passenger window switch. The test lamp should illuminate when commanding the UP and DOWN states.
  12. ?‡'
    If the test lamp is always OFF during either of the commands, test for a short to ground or open/high resistance on either control circuit. If the circuits test normal, replace the PDS.


    ?‡'
    If the test lamp is always ON, test for a short to voltage on either control circuit. If the circuits test normal, replace the DDS.

  13. If all circuits test normal, test or replace the passenger window motor.

Sep 08, 2016 | 1994 Chevrolet C/K 2500

1 Answer

I have a saturn ion 06 coupe, neither of my windows are working! I have checked the fuse replaced both motord\regulators and the switches. They're still not working!! Plz help


Please do these check and let me know.

Diagnostic Fault Information

Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

Circuit/System Description

The power window system will operate any time the ignition is the ACC or RUN position. The power window system will also operate whenever the body control module (BCM) is in retained accessory power (RAP) mode. The driver power window switch contains individual window switches for each of power windows. All windows may be controlled up and down from the driver power window switch. The individual passenger power window switches will only control the up and down operation of their respective power window.
Each power window contains a reversible power window motor. The direction the window travels is dependent upon the polarity of the supply voltage. By reversing polarity of the supply voltage the window motor will move up or down. Each power window motor is internally circuit breaker protected.
Battery voltage is supplied to the power window switch through the accessory voltage supply circuit. The power window switch also receives a constant ground source. The power window motor control circuits are connected to ground through the normally closed up and down contacts of the power window switch. When the power switch is placed in the down position, the power window motor down control circuit is switched to 12 volts and is applied to the down side of the power window motor. Since the other side of the power motor is connected to ground through the normally closed contacts of the up switch, the window travels down. By placing the power window switch in the up position, the polarity of the power window motor is reversed and the window travels up.

Reference Information

Schematic Reference Power Window Schematics
Connector End View Reference Power Door Systems Connector End Views
Description and Operation Power Windows Description and Operation
Electrical Information Reference

Circuit/System Verification

Ignition ON, command the appropriate door window UP and DOWN by pressing the appropriate Window switch. Observe the operation of the appropriate door window.

Circuit/System Testing

  1. Ignition OFF, disconnect the B+ harness connector at the Driver Window Switch.
  2. Ignition OFF, test for less than 1.0 ohm of resistance between the ground circuit terminal D and ground.
  3. ?X If greater than the specified range, test the ground circuit for an open/high resistance.
  4. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal E and ground.
  5. If the test lamp does not illuminate, test the B+ circuit for an open/high resistance. If the PWR WNDW fuse is open, test the circuit terminal C for a short to ground.
  6. If all circuits test normal, test or replace the Driver Window Switch.
  7. Ignition OFF, connect the harness connector at the Driver Window Switch.
  8. Ignition OFF, disconnect the Passenger Window Switch.
  9. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal and ground.
  10. ?X If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.
  11. Ignition OFF, test for less than 1.0 ohm of resistance between the control circuit terminal H and ground.
  12. ?X If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the Driver Window Switch
  13. Ignition OFF, test for less than 1.0 ohm of resistance between the control circuit terminal D and ground.
  14. ?X If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the Driver Window switch
  15. Connect a test lamp between control circuit terminal H and control circuit terminal D.
  16. Ignition ON, command the passenger door window UP and DOWN by pressing the passenger window control on the Driver Window Switch. The test lamp should illuminate during either of the commands.
  17. ?X If the test lamp remains OFF, test for a short to ground or open/high resistance on either control circuit. If all circuits test normal, test or replace the Driver Window Switch.
  18. Ignition OFF, reconnect the Passenger Window Switch.
  19. Ignition OFF, disconnect the harness connector at the appropriate Window Motor.
  20. Ignition OFF, test for less than 1.0 ohm of resistance between the control circuit terminal A and ground.
  21. ?X If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, test or replace the appropriate window switch.
  22. Ignition OFF, test for less than 1.0 ohm of resistance between the control circuit terminal B and ground.
  23. ?X If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, test or replace the appropriate window switch.
  24. Connect a test lamp between control circuit terminal A and control circuit terminal B.
  25. Ignition ON, command the appropriate window UP and DOWN by pressing the appropriate Window Switch. The test lamp should turn ON when commanding the UP and DOWN states.
  26. ?X If the test lamp remains OFF during either of the commands, test for a short to ground on either control circuit. If all circuits test normal, test or replace the appropriate Window Switch
  27. If all circuits test normal, test or replace the appropriate Window Motor.

Component Testing

    Driver Window Switch
  1. Ignition OFF, disconnect the harness connector at the Driver Window switch.
  2. Test for infinite resistance between the signal terminals A and B and the B+ circuit terminal E with the passenger window switch in the INACTIVE position.
  3. ?X If less than infinite resistance, replace the Driver Window switch.
  4. Test for less than 2 ohms of resistance between the signal terminal A and the B+ circuit terminal E with the passenger window switch in the UP position.
  5. ?X If greater than 2 ohms, replace the Driver Window switch.
  6. Test for less than 2 ohms of resistance between the signal terminal B and the B+ circuit terminal E with the passenger window switch in the DOWN position.
  7. ?X If greater than 2 ohms, replace the Driver Window switch.
  8. Test for infinite resistance between the signal terminals F and H and the B+ circuit terminal E with the driver window switch in the INACTIVE position.
  9. ?X If less than infinite resistance, replace the Driver Window switch.
  10. Test for less than 2 ohms of resistance between the signal terminal F and the B+ circuit terminal E with the driver window switch in the UP position.
  11. ?X If greater than 2 ohms, replace the Driver Window switch.
  12. Test for less than 2 ohms of resistance between the signal terminal H and the B+ circuit terminal E with the driver window switch in the DOWN position.
  13. If greater than 2 ohms, replace the Driver Window switch
    Passenger Window Switch
  1. Ignition OFF, disconnect the harness connector at the Passenger Window switch.
  2. Test for infinite resistance between the signal terminals G and F and the B+ circuit terminal with the switch in the INACTIVE position.
  3. ?X If less than infinite resistance, replace the appropriate passenger Window switch.
  4. Test for less than 2 ohms of resistance between the signal terminal G and the B+ circuit terminal with the switch in the UP position.
  5. ?X If greater than 2 ohms, replace the appropriate passenger Window switch.
  6. Test for less than 2 ohms of resistance between the signal terminal F and the B+ circuit terminal with the switch in the DOWN position.
  7. ?X If greater than 2 ohms, replace the appropriate passenger Window switch.
      Window Motor
    1. Install a 30-amp fused jumper wire between the control terminal A and 12 volts. Momentarily install a jumper wire between the control terminal B and ground. The appropriate Window Motor should perform the UP or DOWN function.
    2. ?X If the function does not perform as specified, replace the appropriate Window Motor.
    3. Reverse the jumper wires; the appropriate Window Motor should perform the DOWN or UP function.
    4. ?X If the function does not perform as specified, replace the appropriate Window Motor

Mar 25, 2015 | 2006 Saturn ION

1 Answer

Passenger window switch works but the drivers side switch does not


was regulator bad? did it work from drivers side switch before you did regulator repair?..if so passenger side switch wiring has issue and is not sending signal through it back to the drivers side master switches.. otherwise you need to pin test for power up power down on drivers side switch and repair that if issue going to the window on passenger side.. (possible pinched at door jam area common)

Nov 20, 2013 | 2002 Hyundai Accent

1 Answer

2002 thunderbird window won't go up or down replace swith still wont work fuse are ok does the switch get power


The master switch connector does have circuits that have power on them. The Master switch is not directly connected to the window motors. The switch sends a signal to the Front Electronic Module and the module controls operation of the motor on the driver side. The passenger door window motor is controlled by a different module

Nov 28, 2012 | 2002 Ford Thunderbird

1 Answer

Passenger side power window will not go up or down when weather is hot (+100 F) . Works fine once temp drops. All other windows work fine all the time.


Hello, You need to determine if this is a switch or motor problem. If you are using the Drivers' controls for the Passengers window, try using the Passengers window control on the Passengers door. If one switch works and the other does not, then replace the bad switch.

If neither works you have to check the wiring in the door at the connector to the motor for power. You need a test light or a Voltmeter and check the power going to the Window motor by using the connector plug. Then push your window switch and see if there is power. If you have power, then it only leaves the Window motor to be the problem. Jump the connector from the motor side and see if the Window motor operates.

If you are handy, the solder on the Window motor can be bad and you only need to resolder it. If you go to replace the Window motor, be aware that the right and left sides are different. The door panels have 1 or 2 hidden screws behind trim plugs on the door handle and the speaker grille.

The temperature difference can spread a crack in a piece of Solder and this is most likely why you have a problem. I hope my solution is helpful.

Sep 04, 2011 | 1999 Ford Crown Victoria

1 Answer

2001 dakota passenger side power window not working. Window can be controlled to go down bu not up. Neither the driver side or passenger side controls control it. Replaced motor/regulator. thinking it...


it's probably a broken wire in the door jam on either the drivers sid or the passengers side.check the wires where the fold wher the door opens and closes

Apr 20, 2010 | 2001 Dodge Dakota

1 Answer

Window switch for driver control and passenger switch window


sounds like you have a passenger window motor problem. Try hitting the right door panel hard, down near the speaker opening and pushing the switch at the same time. If it moves, the motor windings are and needs to be replaced.

Mar 26, 2009 | 1999 Mercury Grand Marquis

2 Answers

Passenger side power window suddenly quit working. Window is in "up" position, but will not work from either the driver control switch, nor the passenger control switch.


I had the same problem with my driver side window, so I just replaced the power window motor. It took less than an hour, cost about $35 or $40 and it works perfectly now.

Aug 12, 2008 | 2001 Mitsubishi Eclipse

Not finding what you are looking for?
2002 Pontiac Montana Logo

230 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...