Question about 1994 Jeep Grand Cherokee

1 Answer

Remove back hatch panel - 1994 Jeep Grand Cherokee

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers

Remove the 5 screws bolding liftgate interior trim panel; to aid in removal of the trim panel, start at the bottom of the panel.
Remove the trim panel a wide flat blade tool.

More details can find in ZJ-Secc-8P-Power-Door-Locks (page 4 and next).

I hope help you, good luck (rated this).

Posted on Sep 04, 2009

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How can I unlock rear hatch?


When all else fails, call a dealer.

Nov 10, 2015 | 2005 Buick Terraza

1 Answer

Hatch of mini van not opening


from inside to the panel door ,on the middle is a cup hole (remove it)and open, after that open the door and remove the screws to the interior panel .you will see where the lutch it is stock with tar isolation ..clean that up and replace that draft hole with duct tape ..put everything back the interior panel screws .job done

Feb 19, 2014 | 2000 Dodge Grand Caravan

2 Answers

Jeep Grand Cherokee 1994


Is it the back hatch? Can you pull the rod on the broke side & pull handle at the same time?

May 19, 2013 | Cars & Trucks

1 Answer

2006 envo GMC Envoy back hatch will not open


the release at the bottom of hatch can be ---rusted normal in northeast --- linkage popped or broken --linkage clip popped or broken --- need to crawl into back and remove the plug [ lower center of rear hatch panel will need a long screw driver and light will see linkage and latch push down on linkage arm and push open hatch when opened you can remove the rear panel and assess the problem but lube the latch and upper window latch

Nov 06, 2017 | 2006 GMC Envoy

1 Answer

Replace hatch opener


You need to remove the vinel panel from the rear hatch.Peal back plastic from access hole. Remove 4 hexnuts that hold the tag light , hatch switch and window controller assemply in place.Pop loose assembly from hatch, remove 2pl head screws that hold opner switch to assembly didconect wireing conector. install new switch.

Aug 25, 2012 | 2007 Toyota 4Runner

1 Answer

How does one remove the inside plastic panel / molding on the back hatch?


usally,if there is a pull handle.2screws hold that on and then you can pull or gently pry off panel

Mar 11, 2012 | Cars & Trucks

1 Answer

How to remove hatch panel on 2005 tahoe


  • Release and raise the rear hatch using either the unlock button on the inside of the driver's door or a keyless remote, locate the hatch release on the inside of the hatch, then depress the hatch pins using a flat-head screwdriver, and remove the hatch panel holding clips with the trim panel remover.

  • 2

    Remove the rear hatch release panel with your hands, detach the release cable C-clip with the flathead screwdriver, then carefully pull the hatch wiring out with your hands.

  • 3

    Remove the rear hatch release with the ratchet and socket.




  • Dec 31, 2011 | 2005 Chevrolet Tahoe

    1 Answer

    Back hatch won't open.need info on getting it open.need info on getting the back panel off the inside of the hatch to get to the motorof it. the electric switch on the hatch window, has to be unlocked...


    your going to have to remove it from the inside, remove as many screws as you can that hold the panel on, then pry panel open until you can reach linkage to pop window and then linkage to open rear gate. good luck.

    Dec 20, 2009 | 2002 Chevrolet Blazer

    3 Answers

    I cant open the glass on my back hatch any suggestions?


    The glass hatch release handles fail all the time on these models (which is why the system was eliminated in 2009 models).

    The glass hatch handle is $32 list from the dealer.

    Removal and replacement requires a philips screwdriver and a 10mm socket and ratchet with extension.

    Open the glass hatch by manually activating it through the access hole on the inside of the tailgate (small square panel covering it)

    Remove the two philips screws and the one pop fastener holding the plastic trim on the back of the glass hatch handle area.

    Remove the two 10mm nuts holding the handle on, unplug the wire and remove, noting the routing of the wiring on removal.

    Reassemble in opposite order, being sure to route the wiring correctly.

    Oct 29, 2009 | 2004 Mitsubishi Endeavor

    1 Answer

    Replacing outer tail light on Lexus RX300 ?


    Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-fareast-font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Lift the hatch. The tall center light is located behind the upper hatch inside panel. There are two panels need to remove. One panel is on the right, the other on the left. To remove the panels you have to use flat screw driver to pry out the panel in several locations. (These panels are secured by several small metal clips.) Be careful to collect all these clips and replace them on the back of the panel. You will need these clips to replace the panel later on. After remove the panels, you will be able to locate the screws on the tall center stop light assembly. Remove those screws and cover. After replacing light bulb. Assemble everything in reverse order. Remember, the metal clips have to set on the back of the two panels not the car body.

    Jul 04, 2009 | 2002 Lexus RX 300

    Not finding what you are looking for?
    1994 Jeep Grand Cherokee Logo

    340 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jeep Experts

    yadayada
    yadayada

    Level 3 Expert

    78267 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Kevin Daniels

    Level 3 Expert

    1455 Answers

    Are you a Jeep Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...