Question about 2002 Hyundai Accent

Open Question

How do i set the timing marks on the camshaft with regard to the crank i see two marks on the cam

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1966 chrysler 300/383 engine camshaft timing installation procedure with piston @ top dead center compression of #1 cylinder


Cam timing is set to zero on the crank gear, timing mark on gear point directly up to camshaft gear mark.

Sep 28, 2016 | Chrysler Cars & Trucks

1 Answer

How will I time my cam belt ?


Every engine has a method for aligning the cam-to-crank for installing timing belts/chains.
On a dual-Camshaft Renault there will be a mark on each of the camshaft pulleys - the camshaft marks should be aligned with each other while the mark on the crank should point to a corresponding mark (arrow) on the engine block when the belt is installed.
I did a quick search for "renault timing belt marks" which produced a multitude of images and examples. One of those should be a close match for your engine. Good Luck !.

Nov 16, 2014 | 2003 Renault 181

1 Answer

Set camshaft timing


there should be marks on crank pully and cam belt pully. rotate motor until crank pully timing mark is on zero.the cam belt pully should be lined up with its own mark.number one piston should be at the top of its stroke (top dead centre TDC) and number one valves should be shut. if the cam belt mark is not alined with its own mark remove the belt realine the marks and refit the belt

Sep 15, 2013 | 1993 Subaru Legacy

1 Answer

I replace timing belt but cant set timing


Hi Robert, It would help to know what engine is in your vehicle? A rule of thumb way to set up the valve timing is as follows. Rotate the crank shaft until the crank shaft mark is about 90 degrees from TDC. This will protect the valves from damage when rotating the cams to align them. With the tappet cover removed rotate the cam shaft or shafts so that the number one cylinder is on compression (both inlet and exhaust valves fully closed) and the last cylinder in line on overlap, Look for adjacent timing marks on the cam gears and somewhere close to those look for the alignment marks (maybe notch marks, holes or indented match marks). (Some manufactures use the machined gasket surface where the tappet cover closes onto the cylinder head). Look closely for the static mark on the cylinder head and align the cam(s) to it or them. Once completed, set the crank at Top Dead Center and look carefully for a timing mark which aligns with the gear and set them. Fit the belt so the marks align when the tensioner bearing is released and presses the belt under load. (follow the manufactures recommended tightening instructions.) . (Remember never to crimp a timing belt, if it has been, throw it away and get another, even if it is new!) If the belt snapped and that is the reason for replacement, internal damage may have resulted inside the engine. A snapped belt may cause damage to the valves, the camshafts, the cam shaft caps and to the pistons. If the engine turns much faster than expected and sounds as if there is no compression, you have problems! (Those I've just mentioned. I hope not for your sake. best of luck Regards John

Dec 12, 2011 | 2000 Hyundai Accent

1 Answer

Diagram_hyundai trajet V6 2.7Ltr engine ( 2000 Model )


  • You want to align the Crank and Cam gears timing mark with the corresponding mark on the engine itself.

  • Camshaft Mark ---


11_3_2011_7_37_49_am.jpg
  • Crankshaft Marks.

11_3_2011_7_40_20_am.jpg
  • Here is your firing order


11_3_2011_7_44_35_am.jpg

  • Hope this helps.

Nov 03, 2011 | Cars & Trucks

1 Answer

I own a 2004 accent with 122,000 km on it. Long story short, had to get a new head gasket put on, so rocker cover, cams, everything had to come off. Work was done and everything was put back together. I...


P0340 - Cam Timing

SYMPTOMS/CONDITIONS
of a mistimed camshaft system (all must apply):
  1. Camshafts have previously been removed from the engine.
  2. Engine runs rough.
  3. Vehicle sets P0340 (camshaft sensor code).
  4. Camshaft sensor has been checked with a known, properly operating camshaft sensor.

CORRECT:
The diagram in the manuals should show the timing marks on both cam gears to be on the blue timing chain links.

ghost45_11.jpg

Mar 23, 2011 | Hyundai Motor 2004 Accent

1 Answer

How to set the time belt?


4 Cylinder diesel(4JX1) :
1 - Timing mark
2 - Cam pulley
3 - HP Oil pump pulley
4 - Tensioner pulley


suzman_0.jpg

6 Cylinder petrol:
Align crank(C) timing notch mark (1) to oil pump mark.
Align cam pulley(L+R) marks(3) to cylinder head marks
The cam belt has 3 marks, 2 lines and one mark that is actually a row of dots. Align the dots to the crank pulley groove mark(2) and align the other 2 lines to the cam pulley marks. Using a clothes peg to hold the belt to the cam pulleys works wonders to keep it in place while fitting. Please note the arrows on the belt and have them point in the direction of rotation - right to left side of engine
W - water pump pulley
I - Idler pulley
T - Tensioner pulley.

If for some reason you need to realign the cams on each bank :
Standing in front of the car and starting from YOUR left , looking at the cams you should see RE, RI, LI, LE on each of the camshafts.(R for right bank, L for left bank, I for intake and E for exhaust) Right bank camshafts are marked with one dot, left bank with 2 dots on the shaft itself. To align the camshafts to each other each cam shaft gear has a mark on it. Draw an imaginary line between the centre of the camshaft and the centre of the pulley. The alignment mark should be between the two along this imaginary line. The result will be that RI an RE will be at the top of each gear. The same with the left bank.


suzman_2.jpg

Nov 08, 2010 | 1998 Isuzu Rodeo

1 Answer

How to line crank and cam for timing belt on 1988 no crank marks


Hard to explain here... but I believe that car also has the balance shaft which needs to be timed as well. The camshaft has 2 lines which line up to the top of the head, and a "up" or "top" mark at the top.
Crank is set to 0 degrees.

May 02, 2010 | 1988 Honda Accord 4 Door

1 Answer

Set timing


v teck or single, single cam says up on it crank has 2 b on combustion duall cams r facuing each other crank d same
easy call me 559 5796874 california

May 25, 2009 | 1995 Honda Accord

2 Answers

2000 isuzu trooper 3.2 v-6 dohc camshaft timing marks pulled camshafts to do valve job and need to align marks on drive gear and cams


It's more to it than aligning the marks since the cam pulleys turn about three times or more to one turn of the camshaft on this engine. You need to find someone that is experienced on this vehicle.

May 12, 2009 | 2000 Isuzu Trooper

Not finding what you are looking for?
2002 Hyundai Accent Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...