Question about 2005 Dodge Dakota

Open Question

Exact same thing.

My number one went down.  I tried changing the batteries but it still didn't work.  Number two stepped in and did fine;  but within a month it too died.  So now Dodge wants $156 just to diagnose the problem.  Very strange.  I know, like this guys having the same problem, they've seen it many times... they know exactly what's wrong and how to fix it and it would probably take 5 mins.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Suzuki wagon r+gl check engine light keeps flashing and wont start after battery change


the engine (there are more than one engine)
has a distributor.
"have spark at coil down to dizzy but no spark at plugs"
this can mean only 2 things.
1: spark wires are dead. all 4, kinda hard to believe huh?
2: the dizzy is way off time. so time the dizzy and now spark
lands on each wire term.
if not a dizzy engine, post exact version of engine and country.

Apr 14, 2013 | Suzuki SX4 Cars & Trucks

1 Answer

HELP!!! 99 Forester - Both Tail lights dont work and check engine light came on today. any feed back will help


there are 2 fuse boxes, one under the hood in the vicinity of the battery. the other box is usually on the drivers side either under the dash by your feet on the left, or where the door meets the dash. Occasionally it will be found in the glove box on where the passenger door meets the dash.
First thing to do is check the basics, oil level and coolant level in reservoir. (concerning the engine light) If the oil and coolant level is fine you should be safe to drive it to Auto Zone (or other such store, however Auto Zone does it for free) and have them plug in the computer to determine the cause of the engine light, it could be any number of things even the gas cap.
The tail light could be a fuse, however if no fuse is blown it could also be loose wiring. if you do not have an owner's manual, a really great investment is a repair manual, Chilton has the 1999 Forester online at http://seo.chiltonsonline.com/Pub/DIY/Product.aspx?ca=Repair&b=346 this will have step by step instructions on removing panels to check wires and replacing lamps.
check to see if the brake lights work and if they are a different bulb than the tail lights, I had a similar problem in an old Cavalier where the brake lights worked but the tail lights didn't, my problem was in the switch where you turn on the headlights/turn signal. Have a friend help determine what, if any, lights are working in the rear and front of the car.
Auto Parts stores have diagnosis equipment for common issues and are generally very helpful if you have a question about what may cause a problem. ( I have only had a problem with Pep Boys when it comes to being helpful.)
I wish you luck.

Jul 17, 2012 | 1999 Subaru Forester

2 Answers

Replaced Wheel Speed Sensors ABS light still comes on


Yes you can you jump[ terminal A and B and count the number of flashes this will be the code You are a OBD 1 two ways of doing this is a analog voltmeter (count the sweeps) or count the light flashes and match it with the code

Mar 12, 2012 | 1992 Pontiac Sunbird

1 Answer

Car makes a click click but won't turn over..It has been cold


If battery is flat (discharged) that could be one of the problems. Charge the battery or try jump starting from another vehicle, if possible. If it still don't start after trying those two things, it's probably the starter gone bad.
If it starts after charging or jumping, have your battery load tested and
your alternators output checked. Make sure you didn't leave something on for example headlights or something plugged into accessory outlet, could be the reason battery went flat.
In a nut shell, one of these caused this. Bad battery, bad alternator, bad starter or something draiedn battery. Hope this helps.

Jan 18, 2012 | 2007 Chrysler 300 AWD Sedan

1 Answer

I changed the battery in my 2000 corvette and now the radio does not work.


This is a problem with the Theft-Loc system. I believe you will have to take it to the dealer to have the radio unlocked. I found this procedure on the web, but I don't know if it will work. Good luck.

1. Turn the ignition ON (The radio should display "LOC")

2. Hold down the Radio Presets 2 and 3 buttons for six seconds

3. The radio display changes from LOC to a three-digit number. Write this number down. You now have fifteen seconds to complete the next step.

4. Press the AM/FM button

5. The radio display changes to another three-digit number. Write this number to the right of the first one.

6. You now have a six-digit number, the first three digits are from STEP 03 and the last three digits are form STEP 05

7. Call 1-800-537-5140

8. Press 1 then # (pound). You'll hear "Invalid Code, try again"

9. Press 139010 or 106010 or 206010 or 202107 then # (pound). You will be asked to enter your four or six digit code followed by *

10. Enter the number from STEP 6 then *

11. Listen to the four-digit number and write it down. It will be repeated twice

12. Turn the ignition ON (The radio displays LOC)

13. Use the MN and HR buttons to enter the code from STEP 11

14. Press the AM/FM button. The radio display changes to "SEC". Your radio is now "un-locked" and usable.

Mar 27, 2011 | 2000 Chevrolet Corvette

1 Answer

My 1998 chevy blazer radio is locked and i dont have the code to unlock it, can you help me


1. Turn the ignition ON (The radio should display "LOC")
2. Hold down the Radio Presets 2 and 3 buttons for six seconds
3. The radio display changes from LOC to a three-digit number. Write this number down. You now have fifteen seconds to complete the next step.
4. Press the AM/FM button
5. The radio display changes to another three-digit number. Write this number to the right of the first one.
6. You now have a six-digit number, the first three digits are from STEP 03 and the last three digits are form STEP 05
7. Call 1-800-537-5140
8. Press 1 then # (pound). You'll hear "Invalid Code, try again"
9. Press 139010 or 106010 or 206010 or 202107 then # (pound). You will be asked to enter your four or six digit code followed by *
10. Enter the number from STEP 6 then *
11. Listen to the four-digit number and write it down. It will be repeated twice
12. Turn the ignition ON (The radio displays LOC)
13. Use the MN and HR buttons to enter the code from STEP 11
14. Press the AM/FM button. The radio display changes to "SEC". Your radio is now "un-locked" and usable.
Dealership Codes
  • 139010
  • 106010
  • 206010
  • 202107

Troubleshooting
If you fail to enter the correct code eight times, the radio goes into INOP mode. You have to wait an hour with the ignition on before the radio returns to LOC mode.

Read more: http://wiki.answers.com/Q/Code_to_unlock_radio_for_Chevy_blazer#ixzz26wZKnNnU

Nov 23, 2010 | 1998 Chevrolet Blazer

1 Answer

Dead battery lost code to radio.how do i redo the


Procedure:

01. Turn the ignition ON (The radio displays LOC)

02. Hold down the Radio Presets 2 and 3 buttons for six seconds

03. The radio display changes from LOC to a three-digit number. Write this number down. Don’t take forever, fifteen seconds max before the next step.

04. Press the AM/FM button

05. The radio display changes to another three-digit number. Write this number to the right of the first one.

06. You now have a six-digit number, the first three digits are from STEP 03 and the last three digits are form STEP 05

07. Call 1 800 537 5140

08. Press 1 then # (pound). You’ll hear “Invalid Code, try again”

09. Press 139010 then # (pound). You will be asked to enter your four or six digit code followed by * (start)

10. Enter the number from STEP 6 then * (star)

11. Listen to the four-digit number and write it down. It will be repeated twice

12. Turn the ignition ON (The radio displays LOC)

13. Use the MN and HR buttons to enter the code from STEP 11

14. Press the AM/FM button. The radio display changes to SEC Your radio is now “un-locked” and usable. The Theft-Deterrent feature is STILL active! If you want to disable it, use the instruction on page 3-27 in your Y2K Owner’s manual. Use the code from STEP 11 instead of your personal code.


This tip originated from LOTZAHP

Jul 21, 2010 | 1996 GMC Jimmy

3 Answers

2002 mazda protege 5 will not start - will not turn over, starter is fine, battery is new, power is going to the starter, everything is clean, is in park or neutral, no clicking sound at all, fuses are...


Help please....I have Mazda Protege 2002...the car was driving good..and suddenly the car didn't start at all i changed the starter the battery is fine because when i start the car the lights comes on and the radio works. I don't know what is the problem is...when i start the car it makes noise of tik tik. Please help me????

Oct 05, 2009 | 2002 Mazda Protege

3 Answers

I Cant find my radio code please help


Have you looked in the glove box.  Normally honda puts the radio codes on a sticker in or around the glovebox area.  Try this.  If not you will have to take it to the honda dealer and have them get the serial number off the radio and get the code for you

May 29, 2009 | 1997 Honda Accord

1 Answer

Radio locked


I had the same problem with my 1999 Sonoma. try this:
(You must be in your truck with a cell phone handy)

01. Turn the ignition ON (The radio displays LOC)

02. Hold down the Radio Presets 2 and 3 buttons for six seconds

03. The radio display changes from LOC to a three-digit number. Write this number down. Don’t take forever, fifteen seconds max before the next step.

04. Press the AM/FM button

05. The radio display changes to another three-digit number. Write this number to the right of the first one.

06. You now have a six-digit number, the first three digits are from STEP 03 and the last three digits are form STEP 05

07. Call 1 800 537 5140

08. Press 1 then # (pound). You’ll hear “Invalid Code, try again”

09. Press 139010 then # (pound). You will be asked to enter your four or six digit code followed by * (start)

10. Enter the number from STEP 6 then * (star)

11. Listen to the four-digit number and write it down. It will be repeated twice

12. Turn the ignition ON (The radio displays LOC)

13. Use the MN and HR buttons to enter the code from STEP 11

14. Press the AM/FM button. The radio display changes to SEC Your radio is now “un-locked” and usable. The Theft-Deterrent feature is STILL active! If you want to disable it, use the instruction in your Owner’s manual. Use the code from STEP 11 instead of your personal code.

Hope it helps.

Sep 10, 2008 | 2000 Chevrolet S-10

Not finding what you are looking for?
2005 Dodge Dakota Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...