Question about Buick LeSabre

1 Answer

The blades go up two inches and down real fast, then they will make a few complete cycles. There are no obstructions, but I did have the wiper switch disconnected while I changed dash lights. When I reconnected the wiper switch, the fun started

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 291 Answers

Wiper switch should have no effect....lift up on arms to confirm not stripped out at mount....you can take arms completely off,,,,turn on wipers let rotate for short,,,, turn off wipers let them come to park... then turn key off and mount arms back on in the right park position... see if corrects if not write back

Posted on Sep 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace rear wiper blade


buy a complete wiper arm from ebay or amazon because the original blade is not standard the center it thinker than a normal 10 inch blade ..the good thing is when you change the rear wiper arm you can then use normal 11 inch blades when you need to change again the cost of a new arm and blade is around £15 [2016 ] keep the original black cover nut because i found the replacement did not fit over the nut

Feb 08, 2014 | 2005 Hyundai Tucson

1 Answer

Jaguar xk8 problems


loosen the nut at the bottom of the blades so that the wiper motor will work without moving the blades. cycle the wipers and allow the motor to come to the rest position. Fit the blades and tension the nut. Pull the arms off the windscreen and cycle the wiper motor to run until it stops put the wipers back on the screen and see where they are. IF parked properly then OK but if any where then replace the wiper motor as the sequencing gear inside is out of sync with the wiper action.

Dec 25, 2013 | Cars & Trucks

1 Answer

Wiper blades move real slow in the 1st & 2nd position


wiper blade on driver should be 22 inches and the passenger side wiper blade should be shorter make your wiper blades is what factory call for if too long they will move slow hang up.

May 23, 2013 | 2006 Opel Meriva 1.7

1 Answer

Wipers only work on fast speed. The intermitten will not work. When you turn them off they stop at that position.


This is most likely a problem in the Wiper stalk control, although the wiper motor should complete the wipe cycle and Park the blades.

The wiper control is a part of the multifunction switch that it is mounted in. The switch is called an MFS and it is usually replaced as a unit. To replace the MFS switch you will need to remove the steering column cover and on some models, the Ignition switch. The Ignition switch may have a wide round flange on it which will prevent the plastic steering column cover from coming off when you want it to.

The problem can also be in the connectors which attach to the MFS, so I would recommend checking for a loose fitting connector and then trying the wipers again. Be careful not to break the tabs holding the connector to your part. Look for corrosion in the pin connections.

There are several female Torx bolts holding the MFS in position. They will have to be removed and replaced to change the MFS. It is not impossible that the wiper motor is also bad. You will know if the blades still refuse to Park. The intermittent feature and the speeds are part of the MFS switch and that part should work once the MFS is replaced.

If this does not sound like a job you want to perform, a Body shop or Independent mechanical shop can do the job; so can a Dealer. The MFS can run between $65-$95.

Nov 20, 2010 | 2000 Mercury Grand Marquis

1 Answer

Is there a procedure to check the wiper motor on 1991 S10 pickup (only 42000 miles), to be sure it is defective and not a wiring problem?


ONLY PROCEDURE FOR WIPER MOTOR IS YOU HAVE 2 SPEEDS THAT WORK SLOW AND FAST SPEED.WIPERS WILL RETRACT TO THE BOTTOM OF HOOD LINE WHEN YOU TURN OFF. WIPERS SHOULD TURN OFF. CHECK WIPER RESERVOIR MAKE SURE ITS FULL AND WIPER WASHER SPRAY FLUID CLEAN WINDSHIELD. IF WIPER MOTOR DO ALL THE ABOVE THEN ITS OKAY.IF WIPER MOTOR WORKS SLOW LOOK FOR BINDING AT WIPER ARM LINKAGE AND PIVOT LUBRICATE LINKAGE AND PIVOT COULD HELP.IF WIPER MOTOR DONT WORK CHECK FOR POOR GROUND OR BLOWED FUSE.WIPER WORK AT ONE SPEED CONTROL SWITCH IS BAD.IF WIPER BLADES STOP WHERE EVER THEY ARE OR FAIL TO TURN OFF UNLESS YOU TURN OFF IGNITION SWITCH WIPER MOTOR LIMIT SWITCH BROKEN.IF WIPERS DONT RETRACT BELOW BOTTOM HOOD LINE LOOK FOR MECHANICAL OBSTRUCTION OR WIPER MOTOR FAULTY.

Nov 14, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

How do you change a wiper on a 2001 Chevy Trailblazer


hi pull the wiper back from the windowscreen and here is a black plastic clip half way down the wiper blade press that and pull the blade down wards and refit the same way, mesure the blade in inchs so you get the right size for the new one. regards

Jan 25, 2010 | 2003 Chevrolet TrailBlazer

3 Answers

How do you change the rear wiper blade on a 2007 Prius


either you go to the dealor and get a whole new arm wich is toyotas solution to the problem or you go to the auto parst store and ask them for 16 inch insert not a blade just an insert most stores will even instal it for you

Aug 26, 2009 | 2007 Toyota Prius

1 Answer

2004 ram 1500... after a heavy snow fall, now the wiper blades are approx 2 inches above where the stop point should be. when i turn on the blades, they go down before going up.


take them off of the shafts a nut holds them under a plastic cover. turn your key on and turn your wipers on with the wipers removed. then turn wipers off with switch. turn off key an put wipers back on in the correct park position.

Dec 28, 2008 | Dodge Ram 1500 Cars & Trucks

2 Answers

2006 PT Cruiser Wipers Don't work


I had the same problem. It was the wiper computer module according to the dealership. Fortunately it was covered under extended warranty and cost $100 deductible.

Nov 13, 2008 | 2006 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...