Question about 2004 Kia Sedona

Open Question

Back spark plug install - 2004 Kia Sedona

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1989 volvo 740 spark plug installation


simple if you are familiar with engines remove 1 spark plug wire at a time unscrew spark plug replace with new one put wire back on that plug and continue to the next wire remember do one at a time should only be four plugs on that vehicle

Nov 21, 2011 | Cars & Trucks

1 Answer

Plug turned a 1/4 turn and locked down didnt want to force it


no dont force spark plug its trying to cross thread.back spark plug back out.apply thin coat of anti seize compound to spark plug threads.if you have problems getting spark plugs back in a hard to reach place, use a long piece 3/8 vacuum hose about what ever length you need.place vacuum hose over spark plug insulator then install spark plugs to hard reach places to keep from cross threading.if plug tighten 1/4 turn.back out spark plug and try again.dont cross thread or you have to remove cylinder head.if spark plug hole hard to reach to retap or install thread inserts.

Apr 09, 2011 | Toyota Pickup Cars & Trucks

1 Answer

Describe your how fix my pontiac 2000 montana Problem changing spark plugs



Inspection

Inspect for the correct routing of the spark plug wires. Improper routing may cause cross-firing. Inspect each wire for any signs of cranks or splits in the wire. Inspect each plug wire boot for tearing, piercing, arcing, carbon tracking or a corroded terminal.
If there is any corrosion, carbon tracking or arcing indicated on a plug wire boot or terminal, both the plug wire and component it was connected to should be replaced.


Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the left side spark plug wires from the spark plugs.
  3. Remove the left side plug wires from the retaining clips.
  4. Rotate the engine for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. Remove the right side spark plug wires from the spark plugs.
  6. Remove the plug wires from the retaining clip.
  7. Remove the spark wires from the ignition coils.
  8. Remove the plug wire assembly from the engine.
    NOTE If you are replacing the spark plug wires, the spark plug wire conduit and retaining clips should be transferred to the replacement wires.

To install:
  1. Install the right side plug wires to the ignition coils and then the spark plugs.
  2. Install the spark plug wires to the retaining clip.
  3. Rotate the engine back to the original position.
  4. Install the left side spark plug wires to the ignition coils and then to the spark plugs.
  5. Install the spark plug wires to the retaining clips.

3.9L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the intake manifold cover.
  3. Remove the left side spark plug wires as follows:
    1. Disconnect the left side spark plug wires from the spark plugs.
    2. Disconnect the left side spark plug wires from the ignition coil.
    3. Remove the left side spark plug wire clips from the intake manifold and heater inlet and outlet pipe.
    4. Remove the left side spark plug wire assembly.

  4. If removing the right side spark plug wires, the engine must be rotated for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. After rotating the engine, remove the right side spark plug wires as follows:
    1. Disconnect the right side spark plug wires from the spark plugs and ignition coil.

  6. Remove the right side spark plug wire clip from the ignition coil bracket.
  7. Remove the right side spark plug wire assembly.

To install:
  1. Install the spark plug wire assembly.
  2. Install the right side spark plug wire clip at the ignition coil bracket.
  3. Connect the plug wires to the ignition coil and spark plugs.
  4. If the engine was rotated for access, return the engine to the original position.
  5. The remainder of the installation is the reverse order of removal.

Feb 05, 2011 | 2000 Pontiac Montana

2 Answers

How do you replace the spark plugs on a 1998 2.7 Intrepid?


Hi,
REMOVAL
Always remove the ignition coil assembly by grasping at the spark plug boot, turning the assembly 1/2 turn and pulling straight back in a steady motion.
  • Prior to removing the spark plug, spray compressed air around the coil area and spark plug.
  • Remove electrical connector from ignition coil.
On 3.5L engines, it is necessary to loosen the screws by alternating back and forth. Do not lose the spacers under the coil when loosening the screws.
  • Remove 2 fasteners from ignition coil.
  • Remove ignition coil assembly.
  • Remove the spark plug using a quality socket with a rubber or foam insert.
  • Inspect the spark plug condition.
INSTALLATION
Always remove the ignition coil assembly by grasping at the spark plug boot, turning the assembly 1/2 turn and pulling straight back in a steady motion.
  • To avoid cross threading, start the spark plug into the cylinder head by hand.
  • 3.5L engines tighten spark plugs to 28 N·m (20 ft. lbs.) torque, 2.7L engine tighten spark plugs to 17.6 N·m (13 ft. lbs.).
  • Install ignition coil assembly onto spark plug.
  • Install coil screws and tighten: 2.7L engine to 6.2 N·m (55 in. lbs.), 3.5L engines to 6.7 N·m (60 in. lbs.).
  • Connect the electrical connector.

Aug 27, 2010 | 1996 Dodge Intrepid

1 Answer

Replacing spark plugs


Not exactly sure what you need?
Standard Rules:
Use a Spark Plug Socket to remove and install Spark Plugs.
Replace (remove) one Wire at a time from one Spark Plug.
Replace One Spark Plug at a time. Use Anti-Seize Grease applied moderately to the threads on the new Spark Plug.
Using a Socket (with a extension) START all installations using your hands. This prevents cross-threading and stripping of the threads inside the Heads.
Standard Torque 15-20 ft-lbs.
Replace the One Wire connection to that One Spark Plug.
Replace that One Wire connection to the Ignition Coil.
Go onto the next Spark Plug using the above Rules.
Repeat.

For the 3.4L V6:
Firing Order:
1-2-3-4-5-6
Cylinders:
......(back)
1.......3.......5
2.......4.......6
......(front)
Ignition Coil Connections:
............(back)
.|.5..2.|..|.3..6.|..|.4..1.|
............(front)

Mar 21, 2010 | 1997 Chevrolet Venture

2 Answers

How to change spark plug where are they located at


Your spark plugs can be located in 2 different locations.
1 if your engine is sitting front to back of the vehicle your plugs will be located on the drivers side and the passengers side of the vehicle.
2 if your engine is set from one wheel well to the other than your spark plugs will be located on the front of the engine ( front towards the bumper/grill.) and next to the firewall.

4.6L, 5.4L & 6.8L Engines
  1. Disconnect the negative battery cable.
  2. Remove the coil on plugs as outlined under Ignition Coil in this section.

  3. Remove the spark plugs.
  4. Inspect the spark plugs
  5. Adjust the spark plug gap as necessary. Proper gap is 0.52–0.56 in. (1.32–1.42mm).

installation.
  1. Install the spark plugs and tighten them to 13 ft. lbs. (18 Nm) for 4.6L and 5.4L SOHC engines. For 5.4L DOHC and 6.8L engines, tighten the spark plugs to 15 ft. lbs. (20 Nm).
  2. Install the coil on plugs.
  3. Connect the negative battery cable.

Jan 09, 2010 | 2002 Ford Expedition

1 Answer

Replacing spark plugs on a 2004 chevy malibu


2.2L Engine
  1. Observe the following service precautions:

    Allow the engine to cool before removing the spark plugs. Attempting to remove spark plugs from a hot engine can cause the spark plugs to seize. This can damage the cylinder head threads. Clean the spark plug recess area before removing the spark plug. Failure to do so can result in engine damage due to dirt or foreign material entering the cylinder head, or in contamination of the cylinder head threads. Contaminated threads may prevent proper seating of the new spark plug. Use only the spark plugs specified for use in the vehicle. Do not install spark plugs that are either hotter or colder than those specified for the vehicle. Installing spark plugs of another type can severely damage the engine.
  2. Turn the ignition OFF .
  3. Disconnect the Electronic Ignition (EI) module harness connector.
  4. Remove the spark plugs using a 5 / 8 inch spark plug socket.

To install:

WARNING Do not coat spark plug threads with anti-seize compound. If anti-seize compound is used and spark plugs are over-torqued, damage to the cylinder head threads may result.
  1. Inspect the gap on the new spark plugs, re-gap the plugs as required. The spark plug gap specification is 42 inch. (1.0 mm).
  2. Install the spark plugs and tighten to 15 ft. lbs. (20 Nm).
  3. Apply dielectric compound to the spark plug boots and make sure no corrosion is present.
  4. Install the ignition coil housing to cam cover and attachment bolts.
  5. Tighten the ignition coil housing bolts to 89 inch. lbs. (10 Nm).
  6. Connect the EI module harness connector. Push in until a click is heard and pull back to confirm a positive engagement.

Oct 07, 2009 | 2004 Chevrolet Malibu

1 Answer

I need the diagram to put the spark plug cables


2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
  2. Remove the intake manifold cover, if required.
  3. Disconnect the left side spark plug wires from the spark plugs.
  4. Disconnect the left side spark plug wires from the ignition coil.
  5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
  6. Remove the spark plug wire assembly.
  7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
  8. Disconnect the right side spark plug wires from the spark plugs.
  9. Disconnect the right side spark plugs from the ignition coils.
  10. Remove the spark plug wire assembly.
  11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.
To install:
  1. Install the spark plug wire assembly.
  2. Connect the right side spark plugs to the ignition coils.
  3. Connect the right side spark plug wires to the spark plugs.
  4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
  5. Install the spark plug wire assembly.
  6. Connect the left side spark plug wires to the spark plugs.
  7. Connect the left side spark plug wires to the ignition coil.
  8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
  9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
  10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
74d742b.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
306b531.jpg


Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
9313fa7.jpg


Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system
2c9af72.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
d929c16.jpg


Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
f357cd3.jpg

Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system
09e9db9.jpg

I really hope help you with this (remember rated this help) Good luck.

Sep 23, 2009 | 2003 Chevrolet Malibu

1 Answer

How do I change the spark plugs of my 1996 nissan maxima


Using an Allen/Hex key tool, remove the cover to gain access to spark plug holes. This engine has coils at each plug, so after unplugging the electrical connection, you can use either a Phillips screwdriver or an 8mm socket on an extension to remove the 2 screws securing each coil. Pull out the coil and then use a 5/8" spark plug socket on a 6" extension to remove each spark plug. Gap the new plugs to .040" and apply anti-seize lubricant to the threads. Install each plug, slowly at first, so as not to cross-thread it. Torque the plugs to 18 lb/ft. Apply some dielectric grease to the inside of the spark plug boots and re-install the coils. Plug them all back in and re-install the covers. You're done!


PLEASE DO NOT FORGET TO RATE!!!

Mar 13, 2009 | 1996 Nissan Maxima

1 Answer

Spark plugs 2000 cad dts, where are they? how hard to do?


Spark Plugs are Located UNDER COIL Packs
1. Remove the ignition coil cassettes.
2. Remove the spark plug boots. NOTE: Refer to 3. Clean Spark Plug Recess Notice in Service Precautions.
  1. Remove the spark plugs from the cylinder heads.
INSTALLATION PROCEDURE
  1. Measure and adjust the gap of the spark plugs. Refer to Spark Plug Usage. NOTE: Refer to Component Fastener Tightening Notice in Service Precautions.
  2. Install the spark plugs into the cylinder heads. Tighten Tighten the spark plugs to 20 N.m (15 lb ft).
  3. Install the spark plug boots onto the coil cassettes. Ensure that the boots are fully seated against the cassette.
  4. Install the ignition coil cassettes.

Feb 21, 2009 | 2000 Cadillac DeVille

Not finding what you are looking for?
2004 Kia Sedona Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...