Question about 1994 Land Rover Discovery

1 Answer

1994 DISCOVERY, it wont start, theres a problem with the ignition is it the rotor, dist cap or ignition coil

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Land Rover Master
  • 2,030 Answers

Could be any of those or something completely else.
Cant diagnose a no-start usually over the net...have to see what it is doing, any codes?, any readings the vehicle is giving to properly diagnose.

Posted on Sep 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

1994 mustang gt auto trans keeps stalling while


replace fuel filter and if it continues have pump pressure checked

Sep 09, 2014 | 1994 Ford Mustang

1 Answer

1994 mustang gt auto trans keeps stalling while driving sometimes just when warming it up. Check engine light does not stay on when running. Replaced dist, rotor, cap, coil and had ignition module tested....


check for a fuel flow problem( pump pressure-filter blockage-injector/s) run fault codes ( check for HO2S and O2S sensor operation.. Check cat converter is serviceable Blocking exhaust system

Sep 09, 2014 | 1994 Ford Mustang

2 Answers

Not getting any spark out of my plug wires already replaced coil, main relay,and ignition module. could it bemy rotar or distrbut


The Honda system uses a coil that mounts inside the dist, right ?
If you can check voltage output at the coil tower with the cap off you can find out if the coil is firing. If it is, then yes the rotor could be the problem. The voltage has to go thru the cap to the center of the rotor then to each plug terminal. The spark can jump thru the rotor and ground thru the dist shaft.

Jun 23, 2012 | 1991 Honda Accord

1 Answer

Will not start no fire a plugs 1994 sub 350


Check the distributor ignition module in the distributor. Also check to see if you have power going into the distributor. If you do, It's a safe bet that the distributor is bad. Check the cap and rotor if they haven't been changed in awhile. Order of cheapest to most expensive is actually. Power into dist. Cap and rotor, then Dist/module.

Mar 14, 2010 | 1994 Chevrolet Suburban

2 Answers

1994 volvo 850 has no spark, was running and died. Have checked everything back to the computer. Is it possible to check Computers?


Yes,it is possible with diagnostic equipment.In your case you heed to check ignition amplifier and coil.They are together.

Dec 02, 2009 | 1994 Volvo 850

1 Answer

1990 K5 Blazer DIED(Electrical?)?


There may be no injector pulse if the computor does not see a RPM signal.
There will be no spark if the ignition module does not see a dist pulse from the dist pickup.......a RPM signal.
Because you do not have both ......I would suggest to check/change the dist pick up.
Follow the wires from the ignition module inside the dist to the pickup which is also inside the dist.
If it is just a bad dist pickup....keep all your old parts as good spares.
Also...is the dist turning? to provide a RPM signal?
You will have to remove the dist to change the pick-up.....mark your timing locations......"rotor position" and "dist body location"before removal.
A quick test before installing the "repaired dist" .....plug it in the the truck wiring and turn on the key....DO NOT CRANK THE ENGINE OR YOU WILL LOSE YOUR DIST ROTOR CORRECT POSITION......as you spin the dist by hand .....the injectors should spray.

Aug 23, 2009 | 1989 Chevrolet S-10 Blazer

1 Answer

Causes for no spark on 94 jeep cherokee please


Well it could be many things, But have you relpaced the dist. cap and rotor, within the last 15,000 miles or wires and plugs??? next step is the coil ? then it gets fun. like timing. but I think most jeeps with a Inline 6 have a bullet proof engine for the most part. As we all know there is plenty of semi's on the road. well the same set up is there. as an Inline Jeep. I would have to say 90% of semi's on the road are inline 6 cyl. engines. and may of them go to 1million miles.
so plugs,wires, cap, rotor and ignition coil. that is a good starting point.

Mar 24, 2009 | 1994 Jeep Cherokee Country

1 Answer

No Spark


is it a factory dist? if it is, it could be the pickup coil, module.
but do what i do test it out first

Aug 28, 2008 | 1994 Ford F250 Supercab

Not finding what you are looking for?
1994 Land Rover Discovery Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...