Question about Cars & Trucks

1 Answer

I have a ohv16 204206b it spuders until it warms up what could it be do the valves need to be adjusted and what are the specs

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 85,160 Answers

Ohv16 204206b ??

Posted on Aug 15, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 13 Answers

SOURCE: valve adjustment 1978 datsun pu

Not sure on the specs for this but it is readily available from a chilton manual you can get in most  parts stores even walmart.

Posted on Jun 08, 2008

emissionwiz
  • 85160 Answers

SOURCE: need valve adjustment specs for 1979 ford f-250 6 cyl

did u soak the lifters in oil 1st before installing them? if they are pumped up u bring that cylinder u are adjusting up on compression stroke, then adjust rocker to zero lash and then 1/2 more turn of the adjusting nut.

Posted on Mar 22, 2009

jacobwood_17
  • 8 Answers

SOURCE: spuders until warms up and check engine light

check fuel filter first....then plugs

Posted on Jan 01, 2010

tneubauer
  • 437 Answers

SOURCE: I need adjustment specs for my 2007 dodge dakota 3.7 litre

These are hydraulic self adjusting lifters.

Posted on Jan 12, 2010

duane_wong
  • 6826 Answers

SOURCE: i need the engine valve spec for a 1984 chevy 6.2

VALVE ADJUSTMENTS All gasoline and diesel engines in this guide use hydraulic valve lifters, which require no periodic maintenance or adjustment. However, in the event of cylinder head removal or any operation that requires disturbing or removing the rocker arms, the rocker arms must be adjusted in order to position the pushrods to allow the hydraulic lifters to maintain zero lash. Refer to the valve lash adjustment procedure under Rocker Arms, earlier in this Section.

Posted on Aug 21, 2010

Testimonial: "Thanks for this response. After removing the valve cover, they are hydraulic lifters. We called 2 leading parts stores and they did not know that."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need valve lash specs for 1980 suzuki dr400


Suzuki DR400S - Motorcycle Specs

www.motorcyclespecs.co.za/model/suzu/suzuki_dr400s%2080.ht
1980. Engine. Air cooled, four stroke, single cylinder, SOHC, 2 valves per cylinder ....Valve adjustment can be done without a feeler gauge and the CDI has ..

Dr400 valve adjustment 1 - YouTube

? 2:08
www.youtube.com/watch?v=BH-KFrpwo3w
Nov 19, 2010 - Uploaded by obtrailriders
Dr400 valve adjustment 1. ... Suzuki DRZ 400 Valves clearance check \ sprawdzanie luzu zaworowego PART 2 ...

Nov 01, 2015 | Suzuki Cars & Trucks

1 Answer

Needed torqur spec on rocker arms on 1994 gmc 5.7liter


There is no torque spec for rockers. You tighten until there is no backlash, then preload another 1/4 to 1/2 turn. With #1 at TDC on the compression stroke, you adjust #1 by this procedure. You can also adjust intake valves on #'s 2, 5 & 7 as well as exhaust on 3's 1, 3, 4 & 8. Then rotate the engine until #6 is TDC on compression stroke and adjust intakes on #'s 3. 4. 6 & 8 and exhaust on #'s 2, 5, 6 & 7. Good luck.

Oct 01, 2013 | Chevrolet Cars & Trucks

2 Answers

Valve clearance 4g13


make the engine runs for about 30minutes before adjusting the valves,
valve clearances:
intake valve = 0.20mm(0.008 in)
exhaust valve = 0.25mm(0.010 in)
for reference only when the engine is cold,
valve clearances:
intake valve = 0.25mm(0.010 in)
exhaust valve = 0.30mm(0.012 in)
engine specs: mitsubishi 4g13 1.3L (if you have same engine)

Feb 29, 2012 | Mitsubishi Cars & Trucks

1 Answer

What is the difference between hot and cold vavle clearances


When it is stated that valve clearance should be set when hot, you first adjust the clearance on the cold engine after assembly to the hot setting specs if they are the only ones given, then let the vehicle warm up to operating temperature. Then adjust the clearances again.
If it is just a tune-up(undisturbed engine), let the engine warm up to operating temperature, then adjust.
The reason is that metal expands as it heats up, which affects the valve clearance.

Dec 05, 2010 | Toyota Land Cruiser Cars & Trucks

1 Answer

I have a 2000 Mitsubishi Eclipse GT that ticks pretty loud until it warms up. A few people have told me to adjust the valves. What are the specs on adjusting them?


I think the best thing to do is just try a lighter weight fully synthetic oil in it. What you're hearing is the valves sticking in oil that is not bleeding down fast enough while it is cold.

Nov 08, 2010 | 2000 Mitsubishi Eclipse

1 Answer

I have a 91 s10 chevy, and lately i have been having problems with the way it has been running on warm up. When i fire it up it spuders and dies right away. But will run fine after it is warm? i dont know...


Hi there sounds like idle air control valve failure. Or also known as fast idle valve. I would suggest locate and clean. If that doesn't help then replace it and you should be good to go

Nov 04, 2017 | 1991 Chevrolet S-10

2 Answers

Procedure of tappet adjustment


make sure engine is warmed up. Put cylinder one at top dead center,remove the valve cover,loosen all adjustment lock nuts,adust intake and exhaust valves on cyl #1 and intake valve on #2 and exhaust valve on #3. now rotate crankshaft 360 degrees clockwise, now adjust intake valves on cyl#3 and cyl #4 and exhaust valves on cyl #2 and cyl #4.now tighten lock nuts and install valve cover. specs are intake valves 25mm clearance and exhaust 28mm clearance, use a feeler gauge,heres a picture to show you where to check clearance.7675a52.gif

Mar 14, 2010 | 1986 Suzuki Samurai

1 Answer

Roller lifter adjustment 5.7 chevy vortec 1999


Crank the engine until the mark on the damper aligns with the TDC mark on the timing tab and the engine is in #1 firing position.

To adjust a valve back off the adjusting nut until lash is felt at the pushrod. Tighten the nut until all lash is removed. This can be determined by rotating the pushrods with your fngers. When all lash is removed the pushrod will stop rotating. When all play is removed rotate the nut one full turn.

With the engine in #1 firing position the following valves can be adjusted:
Exhaust 1,3,4,8
Intake 1,2,5,7

Crank engine one full revolution - The following valves can now be adjusted:
Exhaust 2,5,6,7
Intake 3,4,6,8

Apr 14, 2009 | 1999 Chevrolet Tahoe

1 Answer

How do you adjust aftermarket roller rocker arms


well first you need to know the firing order...if it's a small block chevy the firing order is 18436572. You need to write the second four digits underneath the first four digits.

so it looks like this 1843
6572

This will let you know which rocker to adjust...turn the engine over by hand using a rachet on the crank shaft bolt by the harmonic balancer until you get both rockers for number 6 cylinder moving at the same time. Now you may adjust the clearance for both rocker for number 1 cylinder. Then crank the engine over by hand again until number 5 cylinder rockers start to move. Now you can adjust the clearance on number 8 cylinder. You will need to know the manufacturer specs for the valve clearance...continue until all rockers have been adjusted.

Note: The engine should be warm when you make the adjustment.

please rate this.

Sep 20, 2008 | Chevrolet Camaro Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22206 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...