Question about 1996 Ford F350 Crew Cab

1 Answer

Where and how to change fuel filter on 1996 Ford F350 7.3 turbo disel truck? Is there more than one fuel filter?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,989 Answers

Please don't forget to rate!!!!

Diesel Engines The 6.9L and 7.3L diesel engines use a one-piece spin-on fuel filter. Do not add fuel to the new fuel filter. Allow the engine to draw fuel through the filter.

  1. Remove the spin-on filter by unscrewing it counterclockwise with your hands or a strap wrench.
  2. Clean the filter mounting surface.
  3. Coat the gasket or the replacement filter with clean diesel fuel. This helps ensure a good seal.
  4. Tighten the filter by hand until the gasket touches the filter mounting surface.
  5. Tighten the filter an additional 1⁄2 turn. NOTE: After changing the fuel filter, the engine will purge the trapped air as it runs. The engine may run roughly and smoke excessively until the air is cleared from the system.

Where and how to change fuel filter on 1996 Ford - fe49580.gif

Posted on Aug 27, 2009

Testimonial: "thanks for getting back to me so quickly . It was very helpful to see the diagram picture where the fuel filter was located and directions. Great!!!"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Lose of power and engine code po0088 comes on


Hello! Code P0088 is telling you the fuel rail pressure is to high...Most common reason is a plugged fuel filter...I would suggest, unless you have recently changed it, replacing the fuel filter first...If that does not clear the trouble I'll need the year, model and engine size to assess the problem further...

Guru............Saailer

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

Aug 23, 2011 | Ford F-250 Cars & Trucks

1 Answer

Fuel filter light came on motor stoped runing changed filter ran good for 20 milessame thing happened again filter looked good this is a 1989 ford 250 disel with less than 90 thousand miles on it. have...


I have run into this concern many times and have had to replace the fuel heater at the bottom of the filter housing but also check for floating metal particles in the part,if they are present replace the filter again

Aug 31, 2010 | 1988 Ford F 250

2 Answers

Ford F250 turbo diesel cut out and died as left house this morning, cold morning. Will not start, not even a cough. Have new fuel filters, need location of the filters, anything else I should check?


if you have the 6.0 then the filters are located on top on the motor right beside your oil filter and under the drivers side on the fuel pump, check to see if you have diesel in your bowl where the fuel filter is, no diesel in there your fuel pump might be dead, check fuses to fuel pump and check relay on the passengers side kicker panel, check your owners manual

Nov 25, 2009 | 2005 Ford F 350 Super Duty

2 Answers

Where is the fuel pump on a 1996 F250 extended cab pickup?


fuel pump IS NOT in the tank, it is between the turbo & the filter housing in the valley

Aug 05, 2009 | 1996 Ford F250 Crew Cab

1 Answer

1996 turbo deisel fuel and oil leak.


The fuel pump is located under the turbo on that truck. It is most likley washing sediment/old fluids out of the vally of toyr engine. It is also driven by a push rod that ths cam drives, so the lower pump o-ring may be leaking too. You can change the fuel pump without pulling the turbo. Good Luck

May 09, 2009 | 1996 Ford F250 Crew Cab

1 Answer

I need to located the IAT sensor for a 1999 FORD F-250 disel 7.3


should be in the air intake tube or filter box

Jan 17, 2009 | 1987 Ford Escort

1 Answer

Ford powerstroke disel 7.3


Sounds like you have blocked fuel supply, check filters.

Jul 29, 2008 | 2001 Ford F250 Super Duty Super Cab

2 Answers

1997 ford diesel 7.3 di turbo


Check the glow plug timer relay. This is what determines the length of time your glow plugs stay on. If it is cycling off too soon, you will have this problem.,

Jul 13, 2008 | 1996 Ford F250 Crew Cab

Not finding what you are looking for?
1996 Ford F350 Crew Cab Logo

Related Topics:

612 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

84027 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22483 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...