1995 Mazda Millenia Logo
Shane Cunningham Posted on Aug 13, 2009
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

I have a '95 2.5 Millenia. the check engine light

I have a '95 2.5 Millenia. the check engine light stays on with P0134 O2 sensor, then P0173 fuel trim malf., then P1170 EGR/barometric sensor. All codes were cleared, then P1195 EGR/barometric sensor stayed on. The next day I went to another shop & got Code 17 engine speed signal. I replaced the ABS relay, but I still have Hard fault check engine light on. Any ideas?

  • Shane Cunningham Aug 13, 2009

    It seems that many others have had a similar problem & after much research, it appears to have something to do with a vaccuum issue, losing pressure at different rates & sending the computer haywire. I hope this helps others.

×

1 Answer

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Master 1,056 Answers
  • Posted on Aug 13, 2009
Anonymous
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Jun 27, 2009
Answers
1056
Questions
1
Helped
363700
Points
3277

This is all due to a loose connection somewere. If your car had been worked on check all connector that are not plugged in tightly. Some newer cars even have a special lock lever to the connectors, and if not connected properly you would have all kinds of code poping up.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Why won't my check engine light on Honda crv go off when I changed the 02 sensor?

P0134 is for #1 o2 sensor no activity. Google this for good info. Maybe you have a broken wire or bad plug. Did you inspect the plug pins going to sensor 1?
1helpful
1answer

P0134 code

Since you are asking where the O2 sensors are, you may already have the answer to this question.
Code 134 is for no activity from bank one sensor one, which is in front of the catalytic converter. The sensor would need to be tested with a scanner.
1helpful
1answer

What is P0134 code?

Front O2 sensor,before catalycic con.
3helpful
1answer

I am getting codes p0141 and p0134, and I have replaced the sensor 1 upstream already

P0141 Heated o2 sensor. P0134 Heater 02 sensor circuit, These 02 sensor has a fuse in the engine junction box listed as IGN 1. This supplies 12volts to the heater circuit, check to make sure its not a open fuse. If you already replaced the sensors make sure you clear the code. or it will stay in memory.
1helpful
1answer

What can cause a 2005 Hyundai Sante Fe check engine light to come on and get all these codes: p0134 - o2 sensor circuit no activity detected (bank 1 sensor 1), p0151 -oxygen sensor circuit,low voltage...

i would check ur fuses that supply voltage to ur o2 sensors, their in the fuse box and usually r labeled o2 sensr. sounds like the o2 sensrs dont have power
0helpful
1answer

I'm thinking about buying a 2002 range rover. It has a service/check engine codes of 134,135,155. Is it likely to be more than oxygen sensor problems? Please reply , Mel

with those codes showing, it could be either bad O2 sensors or there is a problem with the wiring to those sensors. Also, the wrong sensors may be installed. I'm assuming codes P0134, P0135, P0155.

For others viewing this:

P0134 = O2 sensor circuit-no activity detected (bank 1 sensor 1)

P0135 = O2 sensor heater circuit malfunction (bank 1 sensor 1)

P0155 = O2 sensor heater circuit malfunction (bank 2 sensor 1)
1helpful
1answer

95 dodge codes P0340 P0134

P0340 is camshaft position sensor and P0134 is O2 sensor - bank 1, sensor 1. (this is the one before the catalytic converter) Hope this helps.
2helpful
1answer

CODES P0134 AND P0135 ON 96 JETTA .CAR HAS NEUSPEED SUPERCHARGER THAT I INSTALLED CAR RUNS FINE EXCEPT CHECK ENGINE LIGHT KEEPS COMING ON.

P0134- O2 sensor Circ, bank 1, Sensor 1 no activity detected

P0135- O2 sensor heater circ, bank 1 sensor 1 malfunction

1helpful
1answer

O2 Sensor replacement

most cars have only 2 o2 sensors one is below the exaust manifold and the other one near the catalytic converter
3helpful
2answers

1999 Mazda Millenia Check Engine light

it picks up nois inside of the motor it is located in the side of the block under the intake sometimes right above the starter
Not finding what you are looking for?

464 views

Ask a Question

Usually answered in minutes!

Top Mazda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...