I CAN NOT GET WINDSHIELD WASHER SOLVENT TO COME OUT

Removal Procedure
1.) Remove the washer solvent from the washer solvent container.
2.) Remove the air cleaner intake duct.
3.) Disconnect the washer pump electrical connector .
4.) Disconnect the washer hose from the washer pump.
5.) Disconnect the washer solvent level sensor electrical connector.
6.) Remove the washer solvent container screws.
7.) Remove the washer solvent container from the frame rail.



Installation Procedure: the reverse process of removal

There are two relay's in the under hood fuse / relay box . Wiper relay an wiper relay 2 . Maybe one is bad . also check fuse #14 25 amp. Wiper fuse.Plus the BCM - body control module has a hand in making the wipers work . Are you familiar with automotive electronic control modules ?
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Do you have any speed !

There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

It can do harm to seals (the alcohol in washer solvent) I'd flush cooling system and refill w/ new anti freeze.

The washer pump is located directly on the washer solvent resevoir, to remove it just disconnect the washer solvent hose and pump electrical connector, then just pull motor outward. it is just a snap type fit to the resevoir.

you could have a bad washer pump in the washer reservoir. Can you hear the pump run when you turn on the washers? It should hum pretty loud.

If yes, you could have frozen solvent in the ends of the nozzles. Are you in a very cold area?

If yes, use Prestone yellow washer solvent, it doen't freeze like the cheap blue stuff.

Windshield Washer Motor REMOVAL & INSTALLATION 1987-95 Vehicles

1. Disconnect the negative battery cable.
2. Drain or siphon the washer solvent from the reservoir.
3. For 1987-91 vehicles, remove the brace.
4. Unfasten the reservoir screws.
5. Detach the electrical connectors and washer hose.
6. If necessary, remove the reservoir from the vehicle.
7. Remove the washer pump motor from the reservoir. Fig. 1: Location of the windshield washer fluid reservoir and pump - 1987-91 vehicles
   To install:
   
8. Install the washer pump motor on the reservoir. Make sure the pump is fully seated in the reservoir gasket.
9. Position the reservoir in the vehicle.
10. Attach the electrical connectors and washer hose.
11. Install the reservoir retaining screws.
12. Install the brace.
13. Fill the reservoir with washer solvent.
14. Connect the negative battery cable, then check for proper washer pump operation.

1996-99 Vehicles

1. Disconnect the negative battery cable.
2. Drain or siphon the washer solvent from the reservoir.
3. Detach the electrical connectors from the washer.
4. Disconnect the hose from the washer pump.
5. Loosen the nut at the bottom of the washer reservoir.
6. Unfasten the 2 nuts, then remove the washer solvent reservoir.
7. Remove the washer pump from the container.
8. If necessary, remove the solvent lever sensor switch from the washer solvent container. Fig. 2: Exploded view of the washer fluid reservoir, pump and level sensor
   To install:
   
9. Install the solvent level sensor switch in the washer solvent container. The tab on the solvent level sender switch must be lined up with the slot in the hole.
10. Install the washer pump into the reservoir, making sure the pump is pushed all the way into the container seal.
11. Install the washer solvent reservoir and secure with the 3 nuts. Tighten the nuts to 44 inch lbs. (5 Nm).
12. Attach the electrical connectors to the solvent level sensor and washer pump.
13. Connect the hose to the washer pump.
14. Fill the reservoir with washer solvent.
15. Connect the negative battery cable, then check for proper washer pump operation.

Here are the steps to remove the reservoir:

1. Remove the battery and battery tray from the vehicle .
2. Remove the inner wheel housing from the vehicle.This is the plastic liner.
3. Disconnect the electrical connector from the washer pump.
4. Disconnect the electrical connector from the washer solvent level sensor.
5. Disconnect the washer hose from the washer pump.
6. Remove the upper bolt from the washer solvent container.
   
7. Remove the lower bolts from the washer solvent container.
8. Remove the washer solvent container from the vehicle.

If you have used ANYTHING beside windshield solvent in you reservor, you may have created WAXING from soap in the bottom of washer tank, which clogs pump,lines, and nozzel....take the tank out and wash it..disconnect washer hoses at nozzel and clear with compressed air along with the nozzel...if you use solvent only you may have a worn washer pump or restriction...check those and good luck.....

In order to access this, you first need to remove the front left fender inner liner. Then...

• Disconnect the anti-lock brake electrical harness from the washer solvent container.
• Disconnect the washer pump electrical connector
• Disconnect the washer pump hose.
• Remove the push-in retainer from the air induction tube
• Remove the washer solvent container screws
• Finally remove the washer solvent container from the vehicle