Cars & Trucks Logo
Posted on Aug 06, 2009
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

I have a 2003 escalade ext. when i turn on my blinker it flashes normal. when i hit the brakes there normal.however when my blinker and brakes are are the lights go dom and both lights flash and at a faster sequence????i just bought the truck and dont know how long they have been like that.Thanx for any help

  • midwestmason Aug 06, 2009

    could this be due the trailer wiring plug if it wasnt wired correctly? or if its corroted. i have a feeling this truck got wet at one time..i found mildew under the back seat and the carpet is pretty dirty looking.

  • midwestmason Oct 31, 2009

    my truck did the same exact thing..and when i was using cruise and turned a sgnal on it would kick the cruise off..turned out it was all due to a bad ground..follw the taillight wire under under the truck..ground is on drivers frame rail near the back bumper..i took it off cleaned with sandpaper and the blinkers,brakes and cruise all work fine now.

×

1 Answer

Marvin

Level 3:

An expert who has achieved level 3 by getting 1000 points

Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

  • Cadillac Master 85,242 Answers
  • Posted on Aug 06, 2009
Marvin
Cadillac Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

Joined: Jun 20, 2008
Answers
85242
Questions
28
Helped
29053419
Points
266281

THIS PROBLEM MAY BE A DEFECTIVE TURN SIGNAL SWITCH OR A DEFECTIVE BRAKE LIGHT GROUND, THE BRAKE LIGHTS ARE GROUNDED NEAR THE SOCKETS, YOU WILL NEED TO PULL THE TAIL LIGHT ASSMEBLIES OUT TO CHECK THESE GROUNDS TO THE SHEET METAL.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2008 escalade ext, cant bleed front brakes

some have bleeder screws on the abs control module if this does not help to remove the air i have used syringes filling them up and pressure filling the caliper and air returns to master cylinder takes about 3 ounces of brake fluid per side.
0helpful
1answer

I have a 2003 cadillac escalade ext and the check brake system light came on. The ABS and traction light are also on. What could be the problem?

The most likely problem is a wheel motion sensor. If your check brake light is on, you have a problem that needs immediate attention. Refer to your owners manual to see if your Escalade is still safe to drive.
0helpful
1answer

2003 escalade ext. conected my trailer (1992) to the 7 pin conecter and the brake and turn signals do not work. is this a wiring problem or diferance in configuration between a newer and older vehile.

How are they not working? This is a problem if the trailer has a different set up. Such as the brake and turn signal filament being the same. If that is the problem go to a camper supply store near you and buy and install the convertor box that is made to correct these problems.
0helpful
1answer

I just changed the brakes all the way around a 2003 escalade and now the service brake system message appears......how do i reset that?

Check the ABS hub reluctor ring to make sure it was not damaged in any way when you put everything back together. Also check all the wires to make sure none are crimped or disconnected. Lastly check the brake master cylunder for fluid level. Sometimes after retracting the pistons forcing more fluid into the master cylinder will cause this meesage. If the fluid level is to high simply remove some.
0helpful
1answer

2003 Escalade ran outta gas, now engine won't turn over. Vehicle Stability Control Light is on.

try to fill out the tank and turn the key to the on position several times ,but don't crank it yet ,then turn it all the way over ,that should fill the fuel lines that were emptied.
0helpful
1answer

Suddenly without brakes or power steering

check belt and check p/s fluid if ok pump is probably bad with truck running you should be abel to see the fluid flowing threw th reservior when running
3helpful
1answer

2003 escalade will not start after running it out of gas

My wife ran out of gas once and I had to bleed the fuel lines of air that had been sucked in before gas would travel through the lines. Kinda like you would have to bleed air out of hydraulic brake lines.
Not finding what you are looking for?

407 views

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Sean Wright
Sean Wright

Level 3 Expert

2045 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...