Iv just bought a Vauxhall’s Merida 60 plate, and on the dash board it says e 22, what does this mean?

Your code 21 is just telling you that your left sidelight is out. The shaking and juddering is a different issue and needs a pro grade scan tool computer to see which sensor needs replacing.
21 Failure of left sidelight.

Vauxhall Astra Fault Codes - - Driving Test Tips

https://www.drivingtesttips.biz > fault-codes
Vauxhall Astra Fault Codes List ; 21, Failure of left sidelight. ; 22, Failure of right sidelight. ; 23, Failure of reversing light. ; 24, Failure of number plate ...

service light
service due
or in case service just been done. then need to reset the light

Cylinder head Renew bolts: Yes Tighten: 25 Nm Tighten: 90° Tighten: 90° Tighten: 90° Other engine tightening torques Main bearings Renew bolts/nuts: Yes Main bearings Stage 1: 50 Nm Main bearings Stage 2: 45°-60° Big end bearings Renew bolts/nuts: Yes Big end bearings Stage 1: 35 Nm Big end bearings Stage 2: 45°-60° Oil pump to cylinder block : 6 Nm Sump bolts : 15 Nm Sump drain bolt : 55 Nm Flywheel/driveplate :

• Use new bolts and tighten as follows:
  • 1,4/1,6 = 35 Nm + 30° + 15°
  • 1,8/2,0 = 65 Nm + 30° + 15°
• "Pot"-type flywheel = 65 Nm + 30° + 15°
• Tighten drive plate to 60 Nm.

Clutch pressure plate : 15 Nm Crankshaft pulley/damper centre bolt : Use new bolts. Tighten centre bolt to 130 Nm + 40°-50°
Camshaft sprocket/gear : 45 Nm Camshaft/rocker cover : 8 Nm Inlet manifold to cylinder head : 22 Nm Exhaust manifold to cylinder head : 22 Nm Spark plugs : 25 Nm Lambda sensor (Oxygen) : 30 Nm Chassis tightening torques Front hub :

• Tighten nut in three stages:
  1. 130 Nm
  2. Slacken off
  3. 20 Nm + 80°-90°.

Steering track rod end : New nuts 60 Nm Brake disc to hub Front: 4 Nm Brake caliper to carrier Front: 30 Nm Brake caliper/carrier to hub Front: 95 Nm Brake caliper/carrier to hub Rear: 80 Nm New bolts ABS sensor Front: 8 Nm ABS sensor Rear: 15 Nm Road wheels : 110 Nm
There you go pretty much covers everything hope that helps

check the level of your power steering fluid? or ask someone who knows how?

Have you had an oil pressure switch replaced recently ? If so the problem is probably the engine wiring loom,what happens is the oil leaks into the loom and ends up at the plugs for the ECU and the coil pack and crank sensors,meaning they all need to be replaced.

I'D REPLACE THOSE SENSORS OR REPAIR THE WIRING WHICH EVER IS THE CAUSE. YOU NEED A LIVE DATA SCANNER TO DO THIS REPAIR MOST LIKELY. THAT MEANS THE DEALER.

Hi can someone point me in the right direction iv got a vauxhall zafire b mkll and my engine management light come on so I went and ad it check and the code was p0171 bank 1 running lean so he sed your oxygen sensor so I got a bran new one and put it on about a month ago and yesterday it's my engine management light back on with same code agen any help would be great thanks

call the "plastic surgeon"(yellow pages) they fix dashes in situ.....
and cheap too,better than diy...

my key is not working i have to manually unlock it with the alarm going off and ive lost my manual for the code can you help