Question about Cadillac Cars & Trucks

1 Answer

Where is the Crankshaft Position Sensor located on a 2008 Cadillac SRX AWD 3.6L v6 engine and how do I get to it ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cadillac Master
  • 15,575 Answers

Crankshaft Position Sensor Replacement
Removal Procedure
Turn the ignition OFF.
Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
Remove the exhaust manifold heat shield to obtain access.

Posted on Sep 25, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 337 Answers

SOURCE: location crankshaft position sensor 3.0 24valve engine

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152801f2a83

Posted on Dec 19, 2008

co7196
  • 3433 Answers

SOURCE: need location of crankshaft position sensor on a

The crank sensor should be found at the front by the crank pully. it is bolted to the engine wuth a wire connection plug on it.

Posted on Sep 28, 2009

  • 1608 Answers

SOURCE: where is cylinder #1 on a Cadillac V6 engine 3.6

Right bank is 1,3,5.and left bank is 2,4,6.Hope this helps.Good luck.

Posted on Dec 26, 2009

skychief2001
  • 21873 Answers

SOURCE: replace crankshaft position sensor in 2003 dodge caravan 3.3 V6

According to Haynes, the V6 engine has the sensor mounted in the bellhousing on the back of the engine.

Posted on Aug 21, 2012

ZJLimited
  • 17970 Answers

SOURCE: where is the crankshaft position sensor on a 2003 dodge caravan 33L V6 engine

Hi there:
The 3.3/3.8L crankshaft sensor is located on the rear of the transmission housing, above the differential housing (The bottom of the sensor is positioned next to the drive plate...




8_21_2012_9_41_28_pm.gif

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Aug 21, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, where is the mass airflow sensor located on a 2011 Cadillac SRX?


Hi. When ordering your MAF sensor. Your vehicle has two different engine sizes (2.8L V6 Turbocharged or 3.0L V6). The location of the sensor is the same but the part number is different. Your MAF sensor is located between the top cover (Engine air filter housing) and the TAC (You might identify it as the throttle body).

Sep 10, 2018 | Cadillac Cars & Trucks

1 Answer

Camshaft sensor cadillac srx


DTC P0016: Crankshaft Position (CKP) - Intake Camshaft Position (CMP) Correlation Bank 1
DTC P0017: Crankshaft Position (CKP) - Exhaust Camshaft Position (CMP) Correlation Bank 1

• An actuator that is in the full advance or retard position can cause this DTC to set.
• The presence of DTCs P0008 and P0009 along with P0016, P0017, P0018, and P0019 indicates a possible condition with the primary timing chain and the alignment between both intermediate sprockets and the crankshaft. Or, the crankshaft reluctor wheel has moved and is no longer referenced to top dead center (TDC).
• Observing the desired and actual camshaft angle parameters, with a scan tool before a DTC sets, may help to isolate whether a condition is specific to one camshaft, one bank, or caused by a condition with the primary crankshaft timing.

Now do you want to change a sensor an have it not fix the problem .

May 09, 2017 | Cadillac Cars & Trucks

1 Answer

HOW TO CHANGE THE FUEL PUMP ON 2010 SRX 4 DR. V6


did you test or are you guessing ? The fuel pump relay allows the ECM to energize the fuel pump. The ECM enables the fuel pump whenever the crankshaft position (CKP) sensor pulses are detected. GM Fuel Pump Relay Testing

Dec 01, 2016 | 2010 Cadillac SRX AWD

1 Answer

My 2008 cadillac srx engine light came on and engine power reduce took it to the dealer so they changed the crank shaft sensor but its still not working, can you please help me


if they didn't read the fault codes before starting work, they are repairing by replacement and that is not good
if a sensor is faulty and it could be a cam shaft sensor as well as a crankshaft sensor , normally it misfires or stops altogether
the ECM is in limp mode and that reduced the engine power and if there was a sensor problem it would not just reduce power and put the light on but would show up in a define manner
engine lights also come on it there is a transmission problem and that will also initiate the limp mode
have the fault codes read to determine the faulty part/ sensor

Sep 10, 2016 | 2008 Cadillac Srx

1 Answer

Where is the crankshaft position sensor on a 2008 ford edge, AWD, V6, limited trim package?


In the side of the engine block behind the left side catayltic converter .
  1. Remove the LH catalytic converter.

Jul 16, 2016 | Ford Cars & Trucks

2 Answers

Where is the crankshaft position sensor on my 2010 srx 3 liters


Camshaft/Crankshaft Position Sensor Replacement - Cadillac Forums

www.cadillacforums.com/.../261074-camshaft-crankshaft-position-senso...

May 29, 2012 - 8 posts - ‎4 authors
I have a 2004 CTS - 3.6L and am trying to get the camshaft position ... at my local Auto Zone and it simply shows camshaft position sensor A. Code P0340 Camshaft Position Sensor
14 posts
Mar 23, 2013
How to change the camshaft and crankshaft position ...
6 posts
Oct 9, 2011
Where is camshaft position sensor on 2003?
7 posts
Dec 28, 2009
Crankshaft Position Sensor 3.6L 04 CTS
5 posts
Jul 15, 2008
More results from www.cadillacforums.com

2004 Cadillac DTS crankshaft position sensors - YouTube

? 3:22
https://www.youtube.com/watch?v=jbjLJZzF3xA
Sep 16, 2013 - Uploaded by Rogelio Cervantes
Quick overview crankshaft position sensor replacement for a 2004 Cadillac DTS 4.6 liter North Star. ... 2003 Cadillac CTSCrank Position Sensor Part 3 Done!!! - Duration: 8:21. 2LateIWon 8,433 views. 8:21. How To Check .

Jan 16, 2016 | Cars & Trucks

2 Answers

Location on 2008 Cadillac sts for the crankshaft sensor


Here is the sensor location on the 2005 STS. My understanding is that on the 2005 it sat over the exhaust cam sprocket and on the 2006 it sits over the intake cam sprocket. That should be no problem as there will only be one to locate on your 2008.
location-2008-cadillac-sts-crankshaft-1tpq52gm5e3uksr2cuqtlsek-4-0.jpg

Jan 29, 2015 | 2008 Cadillac STS V6

3 Answers

I have a p0008 code & I'm worried


P0008 CADILLAC - Engine Positions System Performance Bank 1
The ECM detects that both camshafts on either bank of the engine are mis-aligned with the crankshaft for more than 4 seconds or a cumulative of 50 seconds.

The Engine Control Module (ECM) monitors the position of both camshafts and the crankshaft. The ECM performs a test for misalignment between both camshafts on one bank of the engine and the crankshaft. During the test the ECM learns the position of the camshafts and the crankshaft. While the engine is idling, the ECM compares the position of both the camshafts and the crankshaft with the learned value. The ECM will set the P0008 code if both learned values for one bank of the engine are exceeding a calibrated threshold in the same direction.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes
- Engine mechanical problems
- Incorrect timing chain
- Stretched timing chain
- Failed camshaft actuator or actuator solenoid

Tech notes
There is a factory service bulletin for the following Cadillac models:

2004-2008 Cadillac CTS SRX
2005-2008 Cadillac STS

The service bulletin suggest replacing the primary drive and both secondary drive timing chains. Contact your Cadillac dealer for more information. The repair could still be cover under factory warranty.


Hope this helps (remember to rate this answer).

Jun 02, 2011 | Cadillac SRX Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

349 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

Marvin
Marvin

Level 3 Expert

84027 Answers

Jonah Oneal

Level 3 Expert

14059 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22483 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...