2008 Chrysler Sebring windshield wiper relay can't figure where it's at if it's by the fuse box or any help

Question edited for clarity and add maker.
Question moved to model category. There are 4 versions of the 300C including the SRT version.

The first step would be to check the fuses covering those items

Chrysler 300 / 300C (Mk1/LX; 2005-2010) fuses

Fuse-Box.info https://fuse-box.info > chrysler > chrysler-300-300c-m...

Here you will find fuse box diagrams of Chrysler 300 / 300C 2005, 2006, 2007, 2008, 2009 and 2010, get information about the location of the fuse panels ...

Fuses and relays box diagram Chrysler 300

fusesdiagram.com https://fusesdiagram.com > Chrysler

Fuses and relays box diagram Chrysler 300 2004-2010. Identifying and legend fuse box.

Chrysler 300/300C (2005 - 2010) - fuse box diagram

Auto Genius https://www.autogenius.info > chrysler-300-300c-200...
Jan 14, 2021 - Chrysler 300/300C (2005 - 2010) - fuse box diagram. Year of production: 2005, 2006, 2007, 2008, 2009, 2010. Luggage Compartment Fuse Box.

..

The windshield wiper relay on a 2004 Ford F-550 is typically located in the fuse box under the hood. The fuse box is usually located near the front of the vehicle, on the driver's side. To find the windshield wiper relay, you will need to refer to your vehicle's owner's manual or a wiring diagram for the vehicle. The owner's manual should have a diagram of the fuse box that will show you the location of the windshield wiper relay. Alternatively, you can search online for a wiring diagram for your vehicle.

Once you have located the fuse box, you may need to remove a cover to access the fuses and relays. Look for a fuse or relay labeled "wiper" or "wiper relay" to find the windshield wiper relay. If you are having trouble finding the windshield wiper relay, you may want to consider consulting a mechanic or taking your vehicle to a dealership for assistance.

Do you know what a wiring diagram is ? A wiring diagram for your vehicles windshield wipers electrical circuit would show all components involved . You would need a wiring diagram for testing ,so you know which wires too test . It would show the fuse location - amperage etc.... Which of these is your vehicle - Notchback or hatchback or station wagon .

xTooltipElement
Service Information
2008 Holden Viva ' Optra, Viva (VIN J) Service Manual ' Body Systems ' Wipers and Washers ' Schematic and Routing Diagrams ' Document ID: 1964803
--------------------------------------------------------------------------------
Wiper/Washer Schematics
Figure 1: Wiper System - Notchback
Figure 2: Wiper System hatchback and Station Wagon
Figure 3: Wiper System Hatchback and Station Wagon w/Intermittent
Figure 4: Wiper System Notchback w/Rain Sensor
Figure 5: Wiper System Hatchback and Station Wagon w/Rain Sensor
Figure 6: Wiper System Hatchback and Station Wagon w/Intermittent and Rain Sensor
© 2019 General Motors Corporation. All rights reserved.

The fuse would be marked WPR fuse # 9 25 amp. located in the IP fuse panel . IP - instrument panel fuse box . It's location is
Fuse Block - I/P
Behind the left side of the I/P access panel
Windshield Wiper System
The windshield wiper system consists of a wiper motor, a linkage, a wiper arm and a blade, and a wiper/washer switch. The windshield wiper circuit incorporates a self parking device which consists of a worm gear and a cam plate in order to keep the circuit engaged temporarily when the switch is turned off. The wiper system is driven by a permanent magnet-type motor. The windshield wiper motor is mounted on the dash panel and is directly connected to the windshield wiper linkage.
The windshield wiper motor has 2 speeds, LO and HI, and also has intermittent wiper capability. The wiper switch is an integral part of the wiper/washer switch. Windshield wiper operation is actuated through the lever on the right side of the steering column.

https://www.youtube.com/watch?v=MvXX3Xg3siM

WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

The only thing they have in common is the ignition switch.

Highly doubt the fuse being the problem . If the fuse is blown ,that circuit has a problem , short to ground , wiper motor drawing to much amprage . Fuse's do not blow for no reason . Fuse # 18 -30 amp . under hood fuse box . There is also a relay , wiper on/off relay in same under hood fuse box . Also wiper hi/low relay ! There is also alot of electronics involved . integrated power module , front control module , plus C.A.N bus network . How to Diagnose Controller Area Network CAN . Could be wiper / washer switch , wiper motor , communication problem , module problems , Relay problem . Google chrysler intergrated power module . they have had a lot of problems with that thing .

the fuse box under the dash is also a body control module a computer have it checked

The same fuse that protects the wiper motor also protects the washer pump.

put cold water over them not hot