Question about 2003 Toyota Tundra

1 Answer

When to change center support bearing? - 2003 Toyota Tundra

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 139 Answers

If you can grab driveshaft near the bearing and it has alot of play up and down or side to side change it or if you have a vibration when you get on the gas.

Posted on Aug 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change wheel bearings on 2005 tahoe


jack up an secure truck loosen but dont remove center hub nut ,remove wheel, brakes,hang calipre out of way,remove brake support bracket,disconnect abs connector up by frame,remove rotor remove the 3 bolts that hold hub [wheel bearing] in place remove center hub nut remove hub clean area replace hub rebolt all and done

Apr 06, 2013 | 2005 Chevrolet Tahoe

1 Answer

How do you remove the center support bearing on a 1997 c1500 chevy drive shaft


The bearing should slide off the drive shaft. You should be able to buy the bearing and mount together. If the bearing is froze on the shaft you may need a torch.

Aug 28, 2012 | 1997 Chevrolet C1500

1 Answer

How do i change front wheel bearings


Instructions
    • 1

      Jack up the car. Use jack stands if possible, or blocks if not.

    • 2

      Remove tires on the front. Remove brakes.

      • 3

        Take out the grease cap (the center).

      • 4

        Pull out Cotter Pin. Take nut out.

      • 5

        Pull Rotor out. Take grease seal off of the back of the rotor. Pull out inner and outer bearings.

      • 6

        Using hammer and punch, knock out racings from the back of the center of the rotor (very important to use new races, don't use the old ones). Clean out the center of the rotor with a clean rag.

      • 7

        Using the new bearings, replace the old ones, tapping them into place. It doesn't matter which one you install first.

      • 8

        Pack with grease when they are in place. Install new seal after the bearings are packed with grease.

      • 9

        Re-install the rotors into car; put brakes back on; replace tires; You're ready to go!

    Read More: Chinasinoy

    Aug 02, 2012 | 1998 Isuzu Trooper

    1 Answer

    How hard is it to replace that carrier bearing on the drive shaft. i have a f250 2000 superduty.


    Pretty easy! Here are the steps:

    Removal & Installation
    1. Remove 2 center bearing retaining bolts and remove the center bearing and driveshaft assembly.
    2. Check the center bearing for wear or rough action by rotating the inner race while holding the outer race. If wear or roughness is evident, replace the center bearing assembly. Examine the rubber cushion for evidence of hardening, cracking, or deterioration. Replace as required.

    To install:

    1. Place the bearing in the rubber support and the rubber support in the universal shaped support, if removed.
    2. Install the center bearing and drive shaft assembly. While supporting the center bearing in position, install 2 retaining bolts and tighten to 39-53 ft. lbs. (53-72 Nm).
    3. Road test the vehicle and check for proper operation.
    // // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 31; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

    Dec 09, 2010 | 2000 Ford F250 Super Duty Crew Cabs

    1 Answer

    How to i change the bearing on the airconditioner


    to change this bearing requires special mechanics tools. This job can quickly become a real pain if the bearing has been staked on. What level is your mechanical expertise? With all due respect if you do not have pullers and access to presses I would not try this project. At the minimum you will need snap ring pliars, a new bearing, a serpentine belt removal tool, a special puller and a press.
    First remove the serpentine belt. In the center of the compressor pulley there may be a nut that needs removed, remove it. thread in the special pulley clutch removal tool as far as possible with the center bolt of the puller all the way out. With the tool threaded on tighten the center bolt on the tool until the pulley clutch comes off. this works best if you use an impact. now you should see the snap ring on the center hub. remove it. The hub with bearing should now slide off. If it doesnt you will have to use another special puller. Once you get that off you will have to have the bearing pressed out. Likely the outside race will be staked on. it helps if you can grind those off. A machine lathe works wonders for that job. Once the bearing is off put the new one on with the help of a press and a little locktite. You do not need to restake it as long as it fits plenty tight. the rest of the installation is pretty much the reverse of removal. The pulley clutch will need to be pulled on tight with a special tool with special attention given to the gap. You dont want it to touch but you want the clutch faces as close together as possible. good luck.

    Jul 19, 2010 | 1996 Buick Park Avenue

    1 Answer

    How do you change rear bearing on 2000 safari?


    The rear axle bearing? I'm going to presume that's the bearing you're talking about and not the rear main bearing, so please take that into consideration if you would

    You're going to have to jack up the rear of the van, remove the tire and drum. Then you have to place a drain pan under the rear differential and remove the cover. After the cover is removed spin the rear axle (the one with the tire off) to locate the pin in the very center of the differential. On the right side you will see an 8mm (5/16) bolt head.

    When you remove the locking bolt (the 8mm) and slide the pin out DO NOT SPIN THE AXLE WITHOUT THE CENTER PIN IN PLACE. Push in on the axle with the bearing to be replaced and a "C" clip will fall out of the differential. SLIDE THE CENTER PIN BACK IN and screw in the locking bolt a few turns. Once the "C" clip slips out, you can pull the axle out. If you don't have a bearing puller, it's best to rent one. Insert the bearing puller and pop the bearing out.

    Apr 06, 2010 | 2000 GMC Safari

    1 Answer

    Need assistance on how to change the rear wheel bearings on a ford escort 1996 n reg


    If its got drums its no problem, remove the wheel, take off the dust cap in the center of the drum,remove the split pin and the center nut 24mm, i think.
    Take off the drum, clean out the old grease from the bearing, and take out the roller bearings, then you need to knock out the bearing races with a punch.
    Use the old races to knock the new ones in, grease the new bearings and reinsert to the races, reassemble to to rear hub.
    Dont overtighten the nut, nipped up a bit and backed off will do

    Mar 16, 2009 | 1996 Ford Escort 4 Door

    1 Answer

    98 Grand C jeep 4litre crankshaft end play


    Usually this can be done but I think that if you have wear on thrust faces, there is likely wear on support faces as well, Once you have the pan off, plastigage both rod and main bearings. if out of specs, you really should change all of them!! Make sure you torque everything properly and avoid getting oil on backs of bearings when installing... can lead to spun bearing.
    good luck

    Feb 18, 2009 | 1998 Jeep Grand Cherokee

    Not finding what you are looking for?
    2003 Toyota Tundra Logo

    Related Topics:

    188 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...