Question about Nissan Hardbody

1 Answer

I need head bolt torque specifications for 1988 Nissan D21 (3L V-6) engine.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 466 Answers

Cylinder head bolt 40-47 Ft.Lbs o 54-64 N.m

Posted on Aug 02, 2009

  • johnnick1904 May 07, 2011

    i think its 22 to 43 then loosen all bolts and 22 to 40 to 47

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Workshop manual for a 1994 nissan serena


Cylinder head bolt torque sequence
The Rod Bearing Cap Torque
The Main Bearing Cap Torque 38 Foot pounds (Final torque)


Step 1: Torque 10-12 Ft/LbsStep 2: Torque 17-21 Ft/Lbs


Note :
Torque sequence ------------------------
' 11 '
front ' 13 9 3 1 6 8 '
of ' '
engine ' 14 7 5 2 4 10 '
' 12 15 '
------------------------
Step 1: Torque all bolts in sequence 22 Ft/Lbs
Step 2: Torque all bolts in sequence 47 Ft/Lbs
Step 3: Loosen all bolts in reverse sequence
Step 4: Retorque all bolts in sequence 22 Ft/Lbs
Step 5: Retorque all bolts in sequence 43-51 Ft/Lbs
Step 6: Retorque bolts 11 thru 15 in sequence an
additional 4-6 Ft/Lbs
** CAUTION ** This engine uses 2 different length head
bolts. "#1" Is the long bolt, while remaining bolts
are short. **Do not confuse location of these bolts**
recheck final torque in sequence

Dec 06, 2012 | Cars & Trucks

Tip

Nissan altima 2.4 L torque specs.


Torque sequence ---------------- | 9 3 1 6 8 | | 7 5 2 4 10 | ---------------- Step 1: Torque in sequence 22 Ft/Lbs Step 2: Torque in sequence 58 Ft/Lbs Step 3: Loosen all bolts completely Step 4: Retorque all bolts in sequence 22 Ft/Lbs Step 5: Retorque all bolts in sequence 54-61 Ft/Lbs recheck final torque in sequence *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque. 0900c15280265395.jpg

on Jul 08, 2010 | Nissan Altima Cars & Trucks

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

1 Answer

Need to know how much torque to tighten head bolts and connectingrods


If you are repairing the engine to this level, a bottom or top rebuild, you should already have a chiltons. If not, what are you doing?! These specifications along with many necessary others should be in your repair manual unless you are just gathering this information for fun. Sorry about the lecture, but if you don't have torque specs for this, what else do you not have. Not only do you need the torque specs but each head bold needs to be torqued in a certain sequence as well. Head bolts are torqued in specific order gradually bringing the cast iron head to specification over three torque sessions.

Jan 22, 2011 | 1988 Jeep Cherokee

1 Answer

I need torque specs for the head bolts on a 2004 Dodge Stratus Coupe 2.4L SOHC


For 2004 Dodge Stratus 2.4L SFI SOHC 4cyl the Head Bolt Torque sequence
------------ | 10 6 2 3 7 | | 9 5 1 4 8 | ------------

Step: 1 - Torque to 25 ft/lbs
Steps: 2 - Torque to 50 ft/lbs
Steps: 3 - Torque to 50 ft/lbs
Steps: 4 - Turn 90 degreesRecheck final torque in sequence

Caution:Engine uses torque to yield head bolts (TTY) that permanently stretch during initial installation. New head bolts must be used when cylinder headis replaced or re installed to obtain proper torque specification.

Hope helps (remember comment and rated this).

Aug 02, 2010 | 2004 Dodge Stratus

3 Answers

Need to know the head bolts torch specs on 98 toyota v6


heres the torque specs and the way to tighten the head bolts for your 1998 toyota sienna, hope this helps,
12 point bolts step 1- 40 ft lbs
step 2- additional 90 degrees
recessed bolt 13 ftlbsaf151d2.gif

May 12, 2010 | 1998 Toyota Sienna

1 Answer

Need engine head torque settings for 2005 nissan sentra 1.8


this is a 6 step procedure first tighten to 37 ft pounds all bolts step 2 turn all bolts 60 degrees step 3 loosen all bolts step 4 retighten to 30 ft pounds step 5 turn bolts 75 degrees and step 6 turn all bolt another 75 degrees

May 29, 2009 | 2005 Nissan Sentra

1 Answer

Need 1990 nissan sentra torque settings and valve clearence


heinrichkemp: The engine in your car is a GA16i
I venture you are asking about the head bolts when you refer to torque settings. The head bolts used on this motor are torque to yield (streach bolts) If you are reusing them, you need to check them to insure they are not stretched beyond limits.
The way you measure the bolt is with a micrometer.
Measuring close to the end where the bolt starts to thread in, about 10-12 threads up, take a reading. Now, go to the other end of the bolt where the threads end and measure about 10 threads in.
There should not be more than a .009 inch difference (.228mm). If there is, discard the bold and get a new one.

You must use a sequence to tighten the bolts, below is the sequence.
11
13 9 3 1 6 8

14 7 5 2 4 10
12 15

torque 11,12,13,14 & 15 to 8.3 Nm (6.1 ft lbs)
Torque the main head bolts by the numbered sequence to
29Nm (22 ft lbs) first pull
64Nm (47 ft lbs) second pull
Loosten all the bolts completely
Tighten the to 29Nm (22 ft lbs) first pull
Tighten bolt # 1 clockwise 85 degrees
Tighten bolts #2- 10 65 degrees
Nissan noted that if you do not have a torque angel meter, you can use a regular torque wrench and torque all the bolts to 69Nm (51 ft lbs)
The valves on this engine have hydraulic lifters, consequently require no adjustment.

Apr 11, 2009 | 1990 Nissan Sentra

1 Answer

Need bolt torque and order for 1988 dodge heads


Torque for your bolts are 105 ft.lbs.

looking forward it would look like this for the order

7 3 1 5

8 4 2 6

Hope this helps you!!!!!

Don't forget to rate!

Mar 17, 2009 | 1988 Dodge Dakota

1 Answer

Torque specs


Head bolt torque is 65 ft lbs, use the below sequence, go over bolts 3x to reach final torque (not all at once to 65)

13 5 2 10
front of engine 17 9 1 6 14
16 12 8 4 3 7 11 15
good luck!

Oct 25, 2008 | 1988 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

484 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...