Question about 2006 Toyota Sienna

1 Answer

Brake light out. Bulb is working properly. What should I check ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,188 Answers

Brake light fuse

Posted on Aug 02, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1114 Answers

SOURCE: Left rear brake light stopped working but bulb and fuses are OK.

take the bulb back out have someone sit in car apply brake get your self a circuit tester and check to see if this circuit is carrying efficient 12 volt current! some times in cold weather these bulbs get hot with long period of breaking and when released condensate and rust begins and you get what you have perhaps bad socket! this would be a ideal location to begin and probably end,

Posted on Jan 03, 2009

MrScary66613
  • 1990 Answers

SOURCE: Left rear brake light stopped working but bulb and fuses are OK.

These are Dual Function Bulbs. They control the Parking Lights and the Brake Lights. This Bulb is Burnt out on the Brake Coil inside the Bulb. I have actually seen Bulbs that were Bad But you could not Tell by jast looking at them. It should be fine with a New Bulb. Please Rate My Response! Thanks!

Posted on Feb 05, 2009

  • 3 Answers

SOURCE: Left brake light not working fuse bulb ok

check all your wiring from the light to the fuse panal. that should fix it

Posted on Apr 19, 2009

  • 521 Answers

SOURCE: 1991 Chevy Corvette Convertible: 3rd. brake light

make sure you have the correct bulb and have it installed in the socket correctly.

Posted on Nov 15, 2009

  • 136 Answers

SOURCE: 2001 Wrangler brake light not

The light assembly is grounded to the body through the mounting screws. It sounds as though it is a bad ground. You could run a ground wire to a bolt on the frame from a mounting screw to check for aground problem.

Posted on Mar 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake lights aren't working


Go to your brake pedal and see if your brake switch is working properly,push it in with hand and see if switch engages and releases when you let up on pedal.It is adjustable.Also check your bulbs to see if the bulb holder is corruded.Check wiring around bulb too.

Aug 07, 2012 | 1999 Toyota Land Cruiser

Tip

Brake Lights Dull or Flickering - All Cars



Dull or Dim Brake Light Repair: If your car has a dull or dim brake light it is dangerous to you and other drivers. A dim brake light is a mystery to most people because the bulb is working, just not correctly. First confirm a new and correct brake light bulb has been installed. Next, turn the ignition key to the "on" position and have a helper depress the brake pedal. With the bulb installed touch a grounded test light to the outer bulb holder ring. If the bulb brightness changes the bulb socket ground has high resistance and needs to be repaired or replaced.

Flickering Brake Light Bulb Repair: A flickering brake light bulb can be very distracting and annoying. A brake light flickers because the power or ground is being obstructed momentarily. The most common cause for this condition is a loose fitting bulb socket. To check for this condition remove the brake light bulb in question, while a helper hold their foot on the brake pedal move the bulb around slightly in the socket. If the bulb flickers replace or repair the bulb socket as needed to regain proper brake light bulb operation. If the brake light bulb socket tests ok wiggle the brake light fuse and wiring at the brake light bulb socket, brake light switch and turn signal switch (American cars). If the brake light bulb flickers repair the component or wiring as needed.
Preferred Procedure: Always replace brake light bulbs with manufacturers recommend replacement bulbs. If you cannot find the correct replacement bulb part number consult an auto parts store for additional manufacturer information.
Common Problems
When brake light bulbs are replaced with the incorrect bulb causing no or dim brake light operation
If the brake lights stay on continuously it could mean the brake light switch has failed or an adjustment is needed.

on Dec 18, 2009 | Honda Civic Cars & Trucks

2 Answers

2003 passat 1.8t, GL My left brake light wasn't getting brighter when I braked for a while, replaced the bulb and no luck. I replaced the bulb housing and it still wasnt working properly until I took...


check to make sure that you have the correct bulb in the correct socket in both left and right tail lights. dual filament bulbs have to contacts on the base of the bottom of the bulb. make sure the socket that you are inserting them into also has two contacts. if that doesn't work then you need to get a test light so you can find out if power is going to the bulb housing and all ground. check all fuses also with amp meter

May 27, 2017 | 2003 Volkswagen Passat

1 Answer

2004 Chevy Trailblazer Brake Light


I would start by trying another bulb. Even though the brake and tail light share the same bulb they actually are powering different filaments inside of the bulb so you can have a tail light filament that is working fine and illuminating properly but have a burned out brake light element that won't work at all...all inside the same bulb. Not uncommon at all to see this problem and these bulbs are pretty inexpensive.

Jul 26, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

Brake light dont work


The rear brake light, passenger side, on my 2002 Olds Silhouette has had a similar problem. After years of frequent replacement of the bulbs, and often having the light not working an hour later, I finally looked into this and discovered that it's a common problem on this vehicle. Some or all of the sockets for the mulitple-bulb assembly are poorly designed, and do not properly hold the bulb in place. You can test this by having someone else pump the brakes on and off while you "jiggle" the bulb in/out/up/down. On mine, the bulb only works if it is inserted all the way and then pulled back out about half way. For whatever reason, this position properly seats the bulb.

Dec 25, 2009 | 2002 Oldsmobile Silhouette

1 Answer

Brake Lights and Hazard still dont work


TEST FRONT RIGHT BLINKER CIRCUIT AND REPLACE THE BULB,,WITH PROPER BULB...A DOUBLE CIRCUIT BULB IN A SINGLE SOCKET WILL DO THAT ALSO A SINGLE SOCKET BULB IN A DOUBLE SOCKET HOLDER....CHECK LEFT SIDE BULB FOR ACURANCY

Aug 29, 2009 | 1993 Chevrolet Astro

2 Answers

Ford focus brake lights stuck on when sidelights on


hi, i have sorted this problem on my 99 focus ghia.,check both your tail light bulbs.someone put the wrong bulb in and i had the exact same problems you described.the bulb for brake/tail light has two steel connecters and and all other bulbs have one.i put proper bulb in and the problem disappeared.now lights working perfect and sidelights dont come on now when i brake :)change both brake/tail bulbs on each side.1 euro will fix this problem.hope this helps.

Jun 01, 2009 | 2006 Ford Focus

1 Answer

My tail lights are not working properly. When I


I agree with shannongreer but also check on the swith at the back of the brake pedal. It's near the top of the pedal almost under the dash.

May 13, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Replaced bulb on right brake light still out


if the left is ok we know that it is not the fuse, so remove the right bulb out and then use a test light and check if you have power at the socket in which you took the bulb out from, usuly the socket is bad or you may have a wire that is broken

Nov 13, 2008 | 2002 Toyota Highlander

Not finding what you are looking for?
2006 Toyota Sienna Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...