Question about 1988 Toyota Pickup

1 Answer

I need to replace the starter for my 87 4x2 Toyota pick-up with the 22R engine. I have removed the 2 lower contacts (one had a plastic connecter and the other bolts on) and the 2 long mounting bolts. There is a 3rd wire on the top of the starter that I am not sure how to remove. I have replaced a starter before on a 00 Camry and it did not have the 3rd wire. Thank you

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Just unplug it pull towards the front.That wire comes from your ignition switch.It tells the starter to start.

Posted on Aug 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a vacuum diagram for a 1980 22RE engine w/ 2 bbl carb


I don't think your engine is a 22R-E as the E denotes electronic fuel ejection. For 1980 it should be just a 22R. I would not suggest slapping on another carb without expecting more work than just hooking up the original vacuum lines. Some lines you could cap off but others would need the vacuum and rerouting. There is plenty of info in the following blog on removing smog devices and extra vacuum lines here:
http://www.yotatech.com/f114/de-smogging-early-22r-205845/
There are also plenty of pictures and diagrams for your engine. Making a trip to your local junkyard might find you a 22R with a carb still attached but it's slim these days. I know this question is from January but if it's too late to help you than maybe it can help some one else.

Jan 01, 2016 | Toyota Pickup Cars & Trucks

1 Answer

What kind of engine does a 1985 toyota celica gts have? And what cars or trucks have that same engine????


Hi, you have the 22R-E engine. This engine was also used in the pick-up and 4-runner. You can read more here:
http://en.wikipedia.org/wiki/Toyota_R_engine#22R

Sep 11, 2011 | 1985 Toyota Celica

1 Answer

Will crank if pushed off, but not with switch on a 1988 toyota pickup, with 22r carb.


Sounds like a bad starter motor or a faulty / intermittent Earth connection.

First check all the battery power and earth leads where they connect to the Battery Terminals, Engine, Starter Motor and Body. If possible disconnect, clean thoroughly by removing any corrosion or paint, with a wire brush or coarse sond paper, that could cause a poor connection, and reconnect making sure all are tight.
Try tapping the starter with a hammer or tyre lever while the starter is operated. If it works then it means that the brushes in the starter are worn out or the solenoid is not making proper contact to switch the high current required. Auto electricians will usually have exchange units available for replacement.

Oct 22, 2010 | 1988 Toyota Pickup

1 Answer

Vacuum diagram for 1987 toyota pick up


727d2c1.jpg

Fig. 11: Emission system component layout and vacuum diagram-1987 22R-E engine


c6d10e0.jpg

Fig. 12: Emission system component layout and vacuum diagram-1987 22R-TE engine

ea6f9c2.jpg

Fig. 13: Emission system component layout and vacuum diagram-1987 22R engine (Federal and Canada)

2220900.jpg

Fig. 14: Emission system component layout and vacuum diagram-1987 22R engine (California)

Hope helps with this (remember comment and rated this).

Jul 15, 2010 | 1987 Toyota Pickup

2 Answers

Where is the fuel filter located on a 1994 toyota pickup?


Not sure what engine you have, but on the 22R or 22RE (2.4 liter four cylinder) It's on the right side (passenger) lower engine just above the oil pan, and in front of the starter motor. You go through the inner wheel well just above the right front wheel. There is an access panel.

May 21, 2010 | 1994 Toyota Pickup

1 Answer

How to remove starter from toyota t100 1995 6-cyl


Remove negative battery terminal... Remove the small lead from the starter solenoid, and the large lead from the starter. remove the (usually 2) bolts holding the starter on. lower starter out the bottom. (now.. since toyota starters don't go bad)... remove the 3 screws from the end of the solenoid housing... and go to a starter rebuild shop. Buy 2 new copper contacts for the solenoid, and replace them... presto new starter for less then $20 bucks.

Mar 03, 2010 | 1995 Toyota T100 Xtracab

1 Answer

How do I replace a starter on a 1985 Toyota PU 4x4? 22R engine Thanks -- Bob R


In order, disconnect negative battery cable, jack up truck and secure it from tipping, access starter from underneath or remove tire and get at it from the wheel well on passenger side, unplug clip and disconnect positive battery cable from starter, remove two bolts that hold it in place. Reverse to install new.

Nov 09, 2009 | 1985 Toyota Pickup

2 Answers

Engine keeps turning over wont start


Year, make, engine and model of the vehicle please.

Dec 12, 2008 | 1986 Toyota Pickup 4WD

3 Answers

1994 Toyota Truck 22R Engine (ext.cab,4x4,5 speed man.) Is it best to remove the truck bed or lower the fuel tank in order to replace the fuel pump? 1994 Toyota Truck 22R Engine


If you're doing it by yourself, drop the fuel tank.
Make sure it's almost out of gas first.

If you pull the bed, it's the bolts that hold the bed in, the wiring to the tail lights, and the tank filler neck to take loose. Then you have to pick up the bed of the pickup (a couple hundred pounds).
To get the tank out, it's the filler neck, and unbolt the straps that hold it in. Depending on how much fuel is in it, is how much it's going to weigh.
But as you loosen the straps, you can use a floor jack to hold the tank up. Same when putting it back in.

So I would go with taking the tank out, and not pulling the bed off.

Aug 01, 2008 | 1994 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...