Question about 2004 Chrysler Town & Country

2 Answers

The abs works fine but the light is always on it has been for years i want to turn it off how can i do this

Posted by on


2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has written 50 answers of more than 400 characters.


    An expert whose answer got voted for 20 times.

  • Expert
  • 124 Answers

If the light is on, then there is a code in the abs module that has not cleared. Either find someone, like a local shop or dealer, who has an abs code reader to find out what it is and clear the code (if there is a code, there is an issue or was at some point, fix it first!). If you don't want to spend a penny, the always unrecommended solution to clear a code is disconnecting the battery for a few minutes. If the light comes back on, there is something wrong, even if you think it working fine. Ask a dealership if there is any known recalls or tsb's.

Posted on Aug 02, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Chrysler Master
  • 6,674 Answers

Have you ever slammed on your brakes in a safe area (like a big parking lot) in the rain to see how it stops? I think I'd try that before I ignore the light.

Posted on Aug 02, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why is my ABS light and on and my radio flickering? and there is a noise like a turn signal in my dash when this happens.

ABS light always on means your ABS is not working properly.Radio flickering : you need to check and cover all ***** electric wiring property by electric tape.Noise in turn signal : please on your car hazard and check all integrator working fine, if not replace fuse bulbs, the problem will be fixed.Hazard Button = (

Apr 13, 2012 | 1996 Isuzu Oasis

1 Answer

Light of ABS is always on . on my Golf 2001 manual diesel. I have had no problem with ABS but light stays on since 1 year ago, Can I turn it off

Only way to turn it off would be to remove the ABS sensor (bad idea and potentially dangerous) or to replace the brake sensor. The part runs between $40-60 and is relatively easy to install.

Feb 20, 2011 | Volkswagen GTI Cars & Trucks

1 Answer

I have 2002 Yukon, the brakes work fine. The ABS unit is shot so the dealer said to turn it off to unplug the fuse so the motor in the unit will stop running however now the ABS lights stay on the entire...

There is no simple way to do this. You can remove the instrument cluster and attempt to remove the bulb or diode but I don't recommend it. These years are notorious for malfunctioning. Repair the unit, a used part shouldn't break the bank and the vehicle safety metrics depend on the abs for stability.

Feb 06, 2018 | GMC Yukon Cars & Trucks

1 Answer

Does the 4 door , 4wd nissan pathfinder have abs?

It should of had ABS. It might not have it anymore. Do you have a light on the dash board that lights up when the key is turned on? How about the owner's manual say anything about it? Most ABS systems go bad in 10 years. and most people pull the bulbs out or put black tape over the light. The brakes still work fine, but no ABS. Check it out, Hope this helps.

Sep 05, 2010 | 1990 Nissan Pathfinder

1 Answer

My check engine light is on. My mechanic said it was the rear wheel speed sensor. That was replaced the brake light and the ABS lights are still on.

could be that your abs sensor is bad.. or that your brake pump is going out. my bmw has the abs light on and has always had it.. car drives fine for 3 years now :)

Jun 08, 2010 | 1997 Isuzu Rodeo

2 Answers

Abs and brake light always on brakes work fine but no abs

low on brake fluid or e-cable not all the way up can cause light to stay on, can computer test as far as abs to see whats wrong,

Feb 07, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

I have a 1994 Honda Accord. When I start the car,

try cleaning sensors behind rotor with brakekleen or something similar had similar problem on my truck & that fixed it road salt & dirt got on sensor

Dec 29, 2009 | 1994 Honda Accord

1 Answer

ABS light alsways on ( is there a way to turn of the ABS indicator light?) please help

The only to get rid of an ABS light is to fix the problem. I would get it scaned and see what it would cost for parts. As long as you don't have a red brake warning light then your base brakes are working. If you have both lights then get it fixed soon, before you have an accident. Good Luck

May 10, 2009 | 2001 Chevrolet Cavalier

2 Answers

ABS Light on 98 Volvo V70

Your car had been designed to work with ABS brakes, if ABS is not working brakes performance can be badly affected, particularly at high speed.
To keep the vehicle safety to standards the ABS should be inspected. At a qualified garage they can connect to ABS system, get an error code in return and diagnose the problem.
Check relays first.

Jul 15, 2008 | 1998 Volvo V70

Not finding what you are looking for?
Cars & Trucks Logo

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides