Question about Ford Bronco

1 Answer

Won't stay running. when i move the the neg cable the electric comes to life but the cable sparks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,982 Answers

Small spark when connecting is normal...large sparks indicate a short. clean the terminal to make sure there is solid connection where sparks are.

Posted on Aug 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Electrical fault in vehicle


Hmmm ok. And what sort of vehicle is it.

Mar 03, 2015 | Cars & Trucks

1 Answer

Where is the fuel pressure release valve on a 2004 kia sedona


Remove the rear seat, remove the access cover and disconnect the electrical connector on the fuel pump. Start the vehicle and let it run until it stalls. Disconnect the neg. battery cable. After the repairs are done reconnect the electrical connector and attach the neg. cable.

Jun 28, 2014 | 2002 Kia Sedona

1 Answer

My car won't stay running when I unhook the


Most alternators are not designed for that much current load. That was a practice that was used several years ago as a test.. but its really ******* alternators and wiring. Leave the battery connected and use a voltmeter to check while the car is running. Set the volt meter on 20 volts or so on the DC setting. Put positive to positive on the battery and neg to neg.. You should see 13.5 volts or above if your alternator is working properly.. Hope this helps..

Aug 18, 2011 | 1985 Ford Tempo

1 Answer

Where do you hook cables to jump start


A lot of people will tell you to hook the good car with the negative on a bolt for ground, I have never had luck with that, never had luck with hooking either car to a bolt, always went right to the battery, hot to hot, neg to neg, If there is no connection, wiggle the cables while turning the key, It should catch. Make sure the donor car is running or you will have 2 dead batteries. Check the water in the dead battery, I have seen them come back to life with just water added. Hope this helps.

Dec 21, 2010 | Dodge Avenger Cars & Trucks

2 Answers

How to hook up 2 new batteries


hook them up in parallel, pos to pos, neg to neg from one battery to another, then pos cable to battery prs and ground cable to neg battery

Jul 29, 2010 | Renault Fuego Cars & Trucks

1 Answer

Charging issue


it sounds like you have a draw on the system. in otherwords something electrical is staying on. take a test light, disconnect the battery cable loose on the neg side. hook the test light between the neg cable and the neg post on the battery.. if the light is bright start pulling fuses out until the light goes out or gets dimmer, because you have to allow for clock etc..once the light goes out find out what that fuse power ups. see if any thing on that circuit is staying on.

Feb 10, 2010 | 1995 Cadillac DeVille

1 Answer

2005 dodge ram wont start


Several Things
Check For Loose Ground Cable (other end not battery end.
There Is Also A Junction Involved (ground) Where Engine And Body Grounds Come Together--LOOK AT THAT FIRST.

Sep 25, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

91 LEGACY STARTED RUNNING ROUGH


The cylinders are numbered as on the spark pack you changed. You might have done better putting the seafoam in the tank as an injector cleaner. Not sure why you changed so many parts, you seem to know how to get the codes from test connector lead hookup and the blink pattern. You might also want to check the fuel rail pressure and the crank and cam angle sensors. Before replacing the injector, swap the #4 injector with the adjacent one and see it the code moves with the injector or stays put. If the code stays on #4, then check the injector wiring, if it moves clean or replace the injector.

Mar 16, 2009 | 1991 Subaru Legacy

1 Answer

Won,t stay running


maby the timing is of or fuel injectors even spark plugs or cables

Jan 09, 2009 | 1984 Dodge Aries

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...