Question about 1991 Toyota Previa

1 Answer

Front end binds up for a while and then drives smooth.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 111 Answers

It'in your Rack&pinion check your power fluid level to make sure it's
full to. this can be tested very easily,

Posted on Sep 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 3.0 ford 4x4 ranger front end is binding up when driving forward and unbinds in reverse.is it a cv axle or vacuum hub assembly.


4 X 4 vehicles are only meant to be in 4 wheel drive on loose surfaces
on hard surfaces where the tires are not permitted to slip there is a torque wing up in the transmission , drive shafts and diffs
this results in hard gear shifting, noisy drive lines and early failures in drive shaft, diffs and transmissions
if you go far enough in reverse it will start to bind up again

Jan 14, 2017 | Ford Cars & Trucks

1 Answer

Feels like front diff is binding


Is it possible that when you replaced the differential you bumped the shifter, causing it to not completly shift into gear? The phrasing of your question is difficult to understand, but good luck.

Dec 05, 2013 | 1995 GMC Jimmy

1 Answer

My 2002 chevy silverado locks up and won't move in 4 wheel drive


most if all problems with the chevy 4x4 at the beginning of problems are the electronics the switches they put crap in the truck and wonder why so many problems to anyone whom sees a problem at the start should first and i mean first clean all the contacts on 4x4 switches the two on the dash and then one on transfer case the one inside the dash sits where people sit drinks like coffee then it runs down dash and onto the switch inside dash you need to take it out clean it good i have fixed more 4x4 problems with doing this first you will not hear this from the dealerships they will tell you you need to replace them when all it is that they need a good cleaning i also take the switch on dash apart and clean contacts then the lights work please try contact cleaner first and more times over it will fix your problems

Jan 07, 2013 | 2002 Chevrolet Silverado 1500

1 Answer

Loud clunk noise front front end when put into 4wheel drive. Also feels like binding when turning?


You have a bad universal joint. you have to take the spindle off to replace this. once the spindle is off you can pull the shaft out. the universal has to be pressed out and back in. As far as the binding, that is normal in close tolerance turns. you get it alittle more with bad joints.
Randy

Nov 09, 2010 | 2005 GMC Sierra 2500HD 4WD

1 Answer

I have a 95 Grand Cherokee Larado.I have a binding noise coming from the front end. Just replaced, bearings and U Joints in front, and seals and bearings in back.


sounds like the drive shafts may not be right back properly or maybe a u joint not seated in straight
jack the truck up and spin whel by hand with 4 wheel locked and look for the binding noise

Apr 14, 2010 | 1995 Jeep Grand Cherokee

1 Answer

How do you adjust the steering box


There is an adjustmen screw on the opposite end of the pitman shaft. If the box is behind the frame There should be an access hole. Raise the veficle off the ground, front wheelsno load. Loosen the adjustment screw and and turn it to the right holding the lock nut.. Move steering wheel back and forth to help take your adjustment. When you feel you have taken up all the slack, turn your steering wheel from one extreme to the other, fulll left and right while feeling for any binding or sluggishness. If you are adjust too tigh, the steering may bind or not return on or after a turn. Ok, O play in pitman shaft. Back adjuster off 1/4 to half turn and lock down with nut. Cycle steering again, full L & R.. You should be set Now lower the front end, cycle steering again and make sure it is smooth and consistant. Check all other steering componants for excessive wear and play before adjusting the box. Repair other defects found. Be cautious in turns until you are absolutely sure the steering will return on its ow. Tets, test, test !!!! Ned

Sep 26, 2009 | 1999 Chevrolet Suburban

1 Answer

My front end seems to bind up and make loud grinding noise with clicking. It then goes back to normal. What could this be?


check your c/v joints on the ends of the front drive axles. a split or torn boot indicates that the joint inside has become contaminated with road dirt and has failed.

Aug 02, 2009 | 1991 Toyota Previa

2 Answers

4 wheel drive is binding in 2002 trailblazer


the trailblazers are designed to shift from 2 wheel to AWD on the fly. BUT NOT TO EITHER OF THE 4 WHEEL OPTIONS. I'd suggest you get it to a mechanic to evaluate the damages.
Jer

Feb 21, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

Steering


There are a couple of causes, and the solutions in order of cost are to first change the gear oil in the front and rear differentials and drive a few miles, then the transmission filter and fluid. finally consider "the infamous torque bind" as detailed at http://legacycentral.org/library/torquebind.htm, but a '91 is very likely to have been resolved by changing the differential fluid.

Jan 21, 2009 | 1991 Subaru Legacy

Not finding what you are looking for?
1991 Toyota Previa Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...