Wasp sting on finger swelling a lot taking Reactine it has been 2 days brusing evident

they take a lot of lining up, it also depends on the temperature you are doing the work in as the wood sweats and gets wider or shrinks, you need to make the room so that the would can shrink
Shrinking and swelling occur as the wood changes moisture content in response to daily as well as seasonal changes in the relative humidity of the atmosphere, i.e., when the air is humid, wood absorbs moisture and swells; when the air is dry, wood loses moisture and shrinks.

I was bit a month ago by a small brown spider.
it left a very swollen lump on my arm that was painful and itchy for 2 weeks.
now its healing up.
If you do not feel sick, you should be ok.
The swelling and sore that develops should hit its peak after 3-5 days, but if it worsens after 5 days, you should surely get it checked out.
There really isn't anything you can do besides take something for the pain and use an antihistamine. Wash it with soap and warm water, then put ice on the wound to reduce swelling.
Hope you feel better soon.

A topical salve might work. Some people are more sensitive to bed bug bites than others. I am one myself, so I have been combatting them for awhile, and believe I have the upper hand.. There is lots of research available on the internet on how to get rid of them. You could also google what product might be best for bites.
You get the stinging sensation about 5 or ten minutes after they have bitten, and within a few minutes more a red welt develops. I have found the less you scratch the bite, the better. In about 45 minutes to an hour the itching starts to subside.
Of all the products I have tried (not that many but a few), the most effective is a spray from Harris. It is in yellow bottles or spray cans. Try Home Best or Walmart for it. It is rather expensive, about 10 or 11 dollars a can, but very effective at killing bugs.
Anyway I hope you find something to help with the bites.

The sting itself is fairly obvious and is now probably gone if you can't see it, but do take care to look around inside the mouth. So close to the mouth and throat is a concern though. If you are able to access one without undue expense, take the child to an emergency dept or doctor and watch carefully for any signs of swelling in the tongue, throat and airway.

Also ask about the possibility of sensitisation and allergic reaction to future stings. All the best with this.
.

take the rear hub off
you will need a hydraulic press or a vice to push bearing out and then in.

no symptoms posted.?
sting, we dont have them here, so what country?
is this is 323 car? 1.3L engine, can you see the starter, have you attempted to even look ,yet?

just starter vague post.
is this just a question of how to replace a starter and not get an acid bath?
1: disconnect battery minus lug. first, always 1st,
2: gain access to starter (remove stuff, or read the FSM)
3: take of the 2 wires from starter solenoid.
4: remove the 2 bolts.
5 it falls out.

or did you mean :?
I have a bad starter, can I repair it,
sure you can 90% of time. (skills good)
but usually the parts add up to more that a rebuilt.
we can show the tests, all great books on starter repair cover this.
in a pinch ive even repaired a solenoid.
ask. for the tests. and steps.
but with zero symptoms , id be forced to show all tests. all steps.
why ask this,..?????

As a life long cold sore sufferer, I can tell you that you can't. It's one of the 1st stages of a cold sore. The swelling does go away after 2-3 days but it then transitions to a cluster of blisters which soon burst open and it goes on and on for 2 wks til it heals. if u can catch it when you only feel that early symptom, itch or tingle, apply Cold Sores Begone Stick and it stops the cold sore before it starts. Look online for it.

Hard to say, it depends on how trustworthy you think they are. From what you say, it appears to be oil seals leaking, you can take a chance and add a Wynn's product to you oil that swells and softens oil seals and stops them leaking. It would be a lot cheaper than a day in the shop and could fix the problem.

Try this: Remove the two (primary & secondary) vacuum diaphram covers & inspect the vacuum diaphrams. If there is any evidence of distortion at the diaphrams, expect to get the condition that you are describing.