Question about 2003 Dodge Neon

1 Answer

I replaced the cam sensor and the car 03 neon will not start?

Posted by on

  • seeulookingc Aug 02, 2009

    yes I did that and also cleared the coades with the coad scaner but when I go to start the car that coad for the cam sensor returns . I only left the batery un done for 10 min would that matter?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 21 Answers

This is a problem Ive encountered before working on a neon i learned that when ever i replaced a sensor the cars computer needed to be rebooted which i did by unplugging the battery for 30 minutes then reattaching it the computer boots up reading all available sensors. i hope this helps you let me no.

Posted on Aug 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2001 dodge neon cranked without the cam sensor connected. what's wrong with this picture?


Changing the Cam Position Sensor on Dodge Neon ...

? 10:33
https://www.youtube.com/watch?v=ciCPQ0kVAQY
Dec 21, 2012 - Uploaded by VeeTheAmazingGreek
... had to change out the cam position sensor on my 2001 Dodge Neon. ... 1997 Dodge Neon no start, crank sensor problems - Duration: 26:53.

Dodge Neon Questions - It will turn over but has no spark ...

www.cargurus.com > Questions > Dodge > Neon

CarGurusAug 9, 2015 - I did have a neon while ago and image crank sensor was bad ... my 1999dodge neon has no spark it will turn over but not fire i have changed the crank sensorcoil ... I have a 2001 Dodge Neon 2.0 with 140,000 kms on it.

Dodge Neon Questions - 2001 Dodge Neon will turn over ...

www.cargurus.com > Questions > Dodge > Neon

CarGurusJan 7, 2013 - I have a 2001 Dodge Neon 2.0 with 140000 kms o... ... went about a month before this recent problem, fixed that with no problem now this. ... firing. you said you replaced the cam sensor, did you do the crank sensor as well? ... My 1996Dodge Neon won't stay running whenever I take my foot off of the gas.

Starting Issues and Trouble Code Due to Defective Cam ...

repairpal.com > Problems > Dodge > Neon

Feb 05, 2016 | 2001 Dodge Neon

1 Answer

My 03 dodge neon died on me I thought it was the Batterie got a jump got home an it did it again Batterie says 13Volts and won't start when I stop it dies Batterie has to be reset everytime


Cam shaft sensor gone bad.replace it .located under the PCV Valve on right side of engine block.DIY under 25.00 and no more stalling out or jumps

Jun 10, 2015 | 2003 Dodge Neon

1 Answer

No spark on 03 dodge neon


There is voltage on all three wires because there is no ground, check with engine cranking. The two wires that go to computer are grounds for coils. You could probably use a noid lite to check for pulse, engine cranking. That should be safe, between primary voltage and one of the grounds. There several ways to visually check for a pulse. If your digital multimeter has a min/max setting, that should work. You could use an l.e.d. but you would have to use resistor.
You changed computer, was it new?

ignition coil-5iatbqqw4bcw3fkj1yoi3lr2-1-0.jpg

May 15, 2017 | 2003 Dodge Neon

1 Answer

I have a 03 neon. it stalls when we start it up, but after 10m sec it turns over. i replaced the fuelpump, plugs and wires, cam and cranksensor.and im out of ideas


did you change the fuel filter at the same time as the pump.you could have a dirty throttle body that just needs to be cleaned.you don`t say if it will start after the initial stalling or if it will start with the throttle held slightly open.you could even have a bad throttle position sensor.how ever it should have set a code in the computer and set the check engine light on.

Mar 15, 2011 | 2003 Dodge Neon

1 Answer

2000 neon cam sensor location?


2000 dodge neon cranks but wont start, but if i unplug the cam sensor it will run for a second

Oct 19, 2009 | 2002 Dodge Neon

2 Answers

2003 Dodge Neon has a pp0340 , 440 codes I think


CODE PO340 NO CAMSHAFT POSITION SENSOR CIRCUIT FAILURE.CODE PO440 EVAP PURGE SYSTEM FAULT.POSSIBLE CAUSE THE EVAP PURGE VALVE VACUUM SUPPLY IS LEAKING OR CLOGGED.OR THE EVAP PURGE SOLENOID HAS FAILED.

Oct 12, 2009 | 2003 Dodge Neon

1 Answer

Cam sensor causing other probelems


the cam sensor definitly can cause the problem. pull the trouble code and make sure the check engine light is for the cam sensor. if so, replace it and retest

May 11, 2009 | 2005 Dodge Neon

2 Answers

Car stalls while driving


you have a bad crankshaft sensor. replace the crank sensor.

dodges and gm's are known for this problem.

Apr 10, 2009 | 1998 Plymouth Neon

1 Answer

99 Neon sohc keeps wipping the cam and crank sensors


Shake or gentle tug on the wiring harness and try starting the engine! I found that my problem was with the cam sensor wiring harness

Oct 07, 2008 | 1999 Dodge Neon

Not finding what you are looking for?
2003 Dodge Neon Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...