Question about 1988 Mazda B2600 Cab Plus

2 Answers

1990 mazda B2600 cab plus runs sometimes .sometimes it starts and will ideal high if you give it gas it boggs down.sometimes it runs fine and sometimes it wont start at all could it be the mass air flow sensor or what im stumped help please

Posted by on

  • ndkxng2008 Aug 02, 2009

    if it was the timing it would be consistently the same not varieable

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 132 Answers

I would check that first and then the timeing.

Posted on Aug 02, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

MINE DOSE THE SOME THING i'D LIKE TO KNOW TO

Posted on Jan 13, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The engine in my mazda b2600 1994 sometimes makes short cut offs in seconds time.i cant find the reason,please help me


comon proble is ignition switch. try moveing key slightly towards off. if vehicle dies, that could be your problem.

Dec 15, 2012 | 1988 Mazda B2600 Cab Plus

1 Answer

How to change front brake pads on a 91 mazda b2600


how to change disk break pads on 92 mazda bravo 4x4

Dec 04, 2011 | 1988 Mazda B2600 Cab Plus

1 Answer

My mazda b2600 1990 has to much fuel in cilinder afterb 20 min runing it dies and the sparks ar blak whit carcoal if i clean them and put them back it wil run again for about 20min what can it be timig...


your fuel pressure is too high......you have a faulty fuel pressure regulator or a bad computer (ECM/ECU). This is a serious problem due to the fact that the excess fuel is dripping into your engine oil. Get the fuel problem fixed and immediately change the oil and filter. If you do not do this, the thin oil will cause a loss in viscosity (lubrcation) and the engine will lock up/throw a rod. Good luck...

Feb 06, 2011 | 1988 Mazda B2600 Cab Plus

1 Answer

How do i remove timing cover off 89 mazda b2600 2.6 seems to be hangin up at the bottom drivers side


put a rope to the car and toll it to the nearest scarp yard and burn the mazda

Nov 09, 2010 | 1988 Mazda B2600 Cab Plus

1 Answer

My 92 double cab mazda b 2600wont run unless you pore gas into inlet manifold. any one have an idea . the motor is injected


This sounds like your electronic fuel pump is bad.Check fuel pressure by purchasing a inexpensive kit around 10 to 15 dollars. Disconnect fuel line by the fuel rail. Install your tester.It should read around 30 psi. Also check filter element.

Oct 15, 2010 | 1988 Mazda B2600 Cab Plus

1 Answer

I need to set up the camshaft timing marks on a 1994 mazda b2600


its not just the camshaft timing marks you set up, you also have to have the crankshaft timing mark set right to or you may damage your engine
check the internet for the right timing procedure for you model car ok

Jun 11, 2010 | 1988 Mazda B2600 Cab Plus

1 Answer

Air in clutch fluid


When you have more fluid, fill it and then crack the bleeder and let it gravity bleed. Check regularly. Bleed off about one resevoir and lock it down. Should be good to go

May 22, 2010 | 1988 Mazda B2600 Cab Plus

1 Answer

Car dying out on acceleration


try having the air flow meter just behind the filter checked i hav a 94 proceed had similar problem and the air flow meter was the cause

Feb 26, 2009 | 1988 Mazda B2600 Cab Plus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

531 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...