Question about 1992 Isuzu Trooper

1 Answer

Isuzu trooper starts briefly then dies

Not getting any fuel in bores but injectors are pulsing. thinking crank sensor fault but can't find it. it's a petrol 3.2 v6 on 1992 plate

Posted by on

  • sykerley Aug 02, 2009

    good answer.i already have a new filter and good fuel supply. it will run on easy start and die as soon as i stop. help. any more ideas.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 1,869 Answers

Check your fuel delivery from the pump to the "dry" pulsing injectors leave the crank sensor alone! open the intake and, spray either (engine start) into the engine then attempt to start; it should start and, run until the either is used up then die. most likely your fuel filters are clogged

Posted on Aug 02, 2009

  • Jim Goldsmith
    Jim Goldsmith Aug 02, 2009

    Check your "rollover" switch to see if it is turning off your fuelpump it is located in the rear; near the fuelpump follow the pump wires also check the intake flap valve (wot)

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 98 Trooper stopped in traffic, now won't start, it cranks till the battery dies. There is a check light blinking below the 4 wheel drive area on the left of the dash


run the fault codes and check for crank/ cam position sensors
broken timing belt, fuel problems
diesel check for air in the fuel system

Nov 20, 2016 | 1998 Isuzu Trooper

1 Answer

Still need an answer to why my 98 explorer wont start ,started just fine 3 minutes prior spins but no start get spark compression fuel but no start if i wait a day or two it almost starts but dies qi


Check if the injectors are pulsing when cranking the engine over. Listen for the tick, or feel for the pulse with your fingertips, or buy a cheap "noid light"-an injector circuit tester- one that fits your injector harness connectors-plug it into an injector connector and crank the car. If circuit is working the noid light will be flashing.
Some anti-theft systems immobilize the injector circuit when they are activated. So you have spark, compression, and fuel to the engine, check the injector circuit.

Dec 01, 2012 | Cars & Trucks

1 Answer

No injector pulse


what vehicle? injector pulse controlled by computer. the computer recieves a pulse from crank angle sensor, or distributor pick up, etc.
then controls injector pulse. Mass air flow on some vehicles determines spray pattern

Jun 29, 2012 | 1991 Chevrolet Cavalier

1 Answer

No negative to my injectors


Fuel injector circuits typically have a power source tied to the ignition switch & the ground is controlled by transistors within the powertrain control module. Ground is only provided during engine operation & cranking. The easiest way to test this is a Noid light or test light. If there is no ground pulse while cranking you should inspect the ignition system. Primarily the Crankshaft Position Sensor. The crankshaft sensor tells the powertrain control module where the engine is in rotation so it can send a signal to the fuel injector at the proper time.

Things to check:
-Power to injector
-Ground pulse during cranking
-Crankshaft Position Sensor

Feb 14, 2011 | 1992 Isuzu Rodeo

1 Answer

The car cranks but won't start. There is no spark, no fuel, no injector pulse. I have manually made the contacts in the shut down relay still nothing. I jumped the fuel relay and the fuel pump runs and I...


If you remove the fuel line and crank the engine and get fuel then you could be assured that the crank sensor works but if there is no fuel while cranking then the crank sensor is most likely the fault. If the crank sensor is not the problem then it is most likely in the coil or distributor which the 97 is notorious for.

Sep 06, 2010 | 1997 Chrysler Cirrus

2 Answers

Isuzu tropper 4jx1


You have no injection pump ,each injector does that job .
You have a faulty rail oil pressure sensor I think ,read my tips to test this sensor .

Feb 06, 2010 | 1998 Isuzu Trooper

2 Answers

Fuel not being delivered. Any ideas. Car was running great no signs or symptoms of trouble. We're in the jungle, any ideas?


is it fireing? is fuel presure getting to injector? look for blown fuse /out of gas/fuel gauge not correct? pickup coil in distributor pulses injectors and fires coil,these are some ideas

Jul 04, 2009 | 1993 Isuzu Trooper

Not finding what you are looking for?
1992 Isuzu Trooper Logo

Related Topics:

750 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...