Question about 2004 Chevrolet Venture Passanger

2 Answers

Drivers side wiper when operating moves off of windshield. I believe that a person could take off wiper arm and reposition it to correct problem. Tried to take wiper arm off , but after loosing bolt...wiper arm will not come off. How does wiper arm come off and is this the way to fix problem?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 315 Answers

Yea you can reposition it. its held one bolt i think. pretty much same thing on all cars.

Posted on Aug 02, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Either the shaft teeth are worn or the screw is stripped. I recommend using JB Underwater Weld for $5

Posted on Aug 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Pontiac Montana wipers not working how to fix


First you need a wiring diagram, free at http://www.bbbind.com/free_tsb.html Then you need a DVOM - digital volt ohm meter to test the circuit . Then if your not familiar with automotive electrical systems testing ,go on youtube an check out Electric Testing Techniques You Need to Know Also having a factory diagnostic trouble shooting chart would also be usefull . You could just start replacing parts , you mite get lucky . The wiper motor is a high fail part , so is the switch ..You could find the fuse is blown ! But fuse's don't usually blow without a reason . Short to ground , low resistance . ( high current flow) Also knowing how they work and what all is involved in making them work.
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Windshield wiper motor module
• Windshield wiper motor
• Windshield washer pump motor
• FRT/WPR/WSHR 25A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all of the low speed modes. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits and the wiper motor high speed circuit.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.
Windshield wiper/washer system MIST operation is identical to LOW operation except that the MIST switch is a press and release type. When the wiper switch is moved to the MIST position and released, low speed wiper motor operation is started and will continue until 1 cycle is complete. If the wiper switch is moved to the MIST position and held, the windshield wiper motor will operate in the LOW mode until the switch is released.

Don't the wipers work in any mode ?
1
Did you review the Wiper/Washer System description and operation and perform the necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Wiper/Washer Systems
2
Turn ON the ignition , with the engine OFF.
Operate the windshield wiper/washer switch through all the switch positions.
Does the windshield wiper/washer system operate normally?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the harness connector of the windshield wiper motor.
Turn the ignition ON, with the engine OFF.
Connect a test lamp from the accessory voltage circuit of the windshield wiper motor to a good ground.
Does the test lamp illuminate?
YES - Go to Step 4
NO - Go to Step 13
4
Connect a test lamp from the accessory voltage circuit to the ground circuit of the windshield wiper motor.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 14
5
Connect a test lamp from the signal 2 circuit of the windshield wiper switch to a good ground.
Press the windshield washer switch.
Does the test lamp illuminate?
YES - Go to Step 11
NO - Go to Step 6
Let me know if you make it this far and i will send rest of diagnostic's

Nov 25, 2016 | 2003 Pontiac Montana

1 Answer

Wiper arm driver Side windshield does not move can move by hand but not when motor is on. Passenger side is fine and works it does not appear to be able to be removed very Easily


If drivers wiper arm will not move by motor operation and can be easily moved by hand ( with wiper on or off ) suspect disconnected/broken linkage. If wiper arm will not move by motor and takes effort ( With wiper on ) by hand... suspect seized wiper pivot

Nov 11, 2015 | Cars & Trucks

2 Answers

Where is the windshield wiper fuse located in the fuse box on a 06 crown victoria


drivers side inner fender under the hood, look in the owners manual for the number and amps. some are marked under the lid itself

Mar 19, 2015 | 2006 Ford Crown Victoria

2 Answers

Where is the fuse box for the wipers


It is under the dash panel right hand side , kick panel ? Fuse F1.1 10amp . an fuse F1.113 30 amp.
Visual Inspection Chart Mechanical Electrical
  • Windshield washer hoses
  • Wiper linkage
  • Multifunction switch
  • CJB fuses:
    • 1 (10A)
    • 38 (25A)
    • 113 (30A)
  • Circuitry
  • Windshield wiper motor
  • The windshield wipers are inoperative
  • Multifunction switch.
  • Circuitry.
  • Ignition switch.
  • Windshield wiper motor.
  • Go To Pinpoint Test A .
PINPOINT TEST A: THE WINDSHIELD WIPERS ARE INOPERATIVE Test Step Result / Action to Take A1 CHECK CIRCUITS 65 (DG) AND 1002 (BK/PK) FOR VOLTAGE
  • Key in OFF position.
  • Disconnect: Windshield Wiper Motor C125.
  • Key in ON position.
  • Measure the voltage between windshield wiper C125 pin 5, circuit 65 (DG), harness side and ground; and between windshield wiper motor C125 pin 8, circuit 1002 (BK/PK), harness side and ground.
    s3j~tr~en~file=a0039065.gif~gen~ref.gif
  • Are the voltages greater than 10 volts?
Yes
GO to A2 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A2 CHECK CIRCUITS 57 (BK) AND 875 (BK/LB) FOR OPENS
  • Key in OFF position.
  • Measure the resistance between windshield wiper C125 pin 6, circuit 57 (BK), harness side and ground; and between windshield wiper motor C125 pin 3, circuit 875 (BK/LB), harness side and ground.
    s3j~tr~en~file=a0037610.gif~gen~ref.gif
  • Are the resistances less than 5 ohms?
Yes
GO to A3 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A3 CHECK THE MULTIFUNCTION SWITCH
  • Disconnect: Multifunction Switch C202a.
  • Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Did the multifunction switch pass the component test?
Yes
GO to A4 .

No
INSTALL a new multifunction switch. REFER to Section 211-05 . A4 CHECK CIRCUIT 57 (BK) FOR OPEN
  • Measure the resistance between C202a pin 4, circuit 57 (BK), harness side and ground.
    s3j~tr~en~file=a0045222.gif~gen~ref.gif
  • Is the resistance less than 5 ohms?
Yes
GO to A5 .

No
REPAIR the circuit. TEST the system for normal operation. A5 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR OPENS
  • Using the following table, measure the resistance between the multifunction switch C202a harness side and the windshield wiper motor C125 harness side:

    Multifunction Switch C202a Windshield Wiper Motor C125 pin 7, circuit 56 (DB/OG) pin 10, circuit 56 (DB/OG) pin 3, circuit 58 (WH) pin 11, circuit 58 (WH) pin 5, circuit 61 (YE/RD) pin 1, circuit 61 (YE/RD) pin 1, circuit 63 (RD) pin 9, circuit 63 (RD)

    s3j~tr~en~file=a0045221.gif~gen~ref.gif
  • Is the resistance less than 5 ohms?
Yes
GO to A6 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A6 CHECK FOR CORRECT WIPER MOTOR OPERATION
  • Disconnect all wiper motor connectors.
  • Check for:
    • corrosion
    • pushed-out pins
  • Connect all wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
GO to A7 .

No
The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. TEST the system for normal operation. A7 CHECK THE WINDSHIELD WIPER MOTOR
  • Key in OFF position.
  • Disconnect: Windshield Wiper Motor C125.
  • Carry out the windshield wiper motor component test as described in this section.
  • Did the windshield wiper motor pass the component test?
Yes
The system is operating correctly at this time. Concern may have been caused by binding or incorrect pivot arm adjustment. REFER to Windshield Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

No
INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section. Hope this helps !

Feb 16, 2015 | 2002 Ford Expedition

1 Answer

1996 crown vic- drivers side wiper arm loose, blade will not lay flat when cleaning


Sometimes you need to bend the arm to put more pressure on the glass.

Mar 29, 2014 | 1996 Ford Crown Victoria

1 Answer

2005 Dodge Magnum RT. Drivers side windshield wiper wants to work, but does not. Had a heavy snow and remotely started the car. Forgot the wipers were on. When I noticed it, the Driver side was off the...


You will need to find where in the linkage the problem is. I would start taking it apart to see what is and what isn't working correctly. Autozone website has free repair manuals available online.

Apr 24, 2013 | Cars & Trucks

1 Answer

2006 hhr passenger side windshield wiper not moving but drivers side is fine??


First remove the complete passenger side wiper check and make sure splines on wiper are not stripped. If this is not the problem It could be a linkage bar from the wiper motor to the wiper off or disconected. Since both wipers share the same motor if one works the other should. Check this by removing both wipers and then "Cawl" (little black piece between the hood and windshield underneath the wipers) Underneath the cawl you should be able to see the windshield wiper motor, and linkage bar to both of the wipers. See if the bar is disconected from the passenger side. If it is than reconnect it. These are the only two possible scenarios.

Jul 18, 2010 | Chevrolet HHR Cars & Trucks

1 Answer

Drivers side windshield wiper not moving


The bolt that holds the wiper on is loose. There is a little plastic cap at the other end of the wiper arm, the side away from the wiper blade. Remove the cap and tighten the bolt. That should get it going again.

Jan 21, 2010 | 1992 Plymouth Sundance

2 Answers

Windshield wiper problem


check the wiper arms first take off the end caps loosen bolts and adjust then tighten then try again please rate my response thank you very much

Jul 17, 2008 | 1998 Pontiac Firebird

Not finding what you are looking for?
2004 Chevrolet Venture Passanger Logo

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...