Question about 1997 GMC Jimmy

1 Answer

I have a 1997 jimmy with a 4.3 it ran fine now wont run at all unless you pull off number 4 spark plug wire then it runs but really rough

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 29 Answers

Replace plug wire set. wire is probably grounding out.
do cap/coil at same time.

Posted on Sep 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 Dodge Dakota and has a 3.9. It's giving a p 304 code. Runs really really rough. valves rattle and everything. put seafoam cleaner through it ran it down the road and has stopped. Had the


DTC P0304: Cylinder 4 misfire detected. Probable cause:
1. Check for latest control unit software update
2. Faulty PCM or ECM
3. Fuel injector(s) faulty
4. Ignition system fault. Check ignition module, coil, spark plugs, and wires
5. Fuel system

Dec 09, 2014 | Dodge Cars & Trucks

1 Answer

'95 Jimmy 4.3L won't start unless plug wire is removed


every possibility that the timing ( firing order) is wrong from what you describe
bring the engine to tdc no1 piston on compression and that is no 1 plug lead in the distributor cap

Mar 15, 2017 | Cars & Trucks

1 Answer

Won't start fuel pump replaced new tank and relay have fuel after fuel filter runs if I put fuel down throttle body. this is on a4,3.


Nephew had similar problem on different vehicle - had spark to plugs, limited gas, everthing else checked. I did one thing first - check for two fuel filters - one in the tank was only screens and one in the line itself. Found a little in line filter just outside of engine compartment under car next to frame that looked like it had never been changed - partially clogged - replaced it.Almost ran but would not keep running. I had rotor and cap pulled - found that the screw holding rotor in place was loose. The rotor edge next to plug wire leads was chopped up and the cap's plug wire leads were heavily oxidized. Replaced them and got it running but a little rough. Pulled the spark plugs and found gaps from 25 - 100 ---replaced the plugs with correct gapping and it ran really well.

Aug 25, 2011 | 1991 GMC S-15 Jimmy

1 Answer

1990 ford ranger 2.3L running rough at idle and while driving


Hi check all the fuse. fi the fuse are ok . remove the coil pack and reverce if the cly missifire change replace the coil if not chage replace the electronic comtrol module ok.

Apr 20, 2009 | 1990 Ford Ranger SuperCab

3 Answers

Have a 1997 ford thunderbird v8...started running very rouhg and check engine light blinking. Changed plugs and wires but noticed small coolant leak above engine. Ran fine for 10 days then started running...


Light should have stored code. Go to local autoparts chain & get free scan for codes and go from there. Saves all that guess work & money a lot of times. Write down code(s) and let us know.

Apr 19, 2009 | 1997 Ford Thunderbird LX

1 Answer

91 LEGACY STARTED RUNNING ROUGH


The cylinders are numbered as on the spark pack you changed. You might have done better putting the seafoam in the tank as an injector cleaner. Not sure why you changed so many parts, you seem to know how to get the codes from test connector lead hookup and the blink pattern. You might also want to check the fuel rail pressure and the crank and cam angle sensors. Before replacing the injector, swap the #4 injector with the adjacent one and see it the code moves with the injector or stays put. If the code stays on #4, then check the injector wiring, if it moves clean or replace the injector.

Mar 16, 2009 | 1991 Subaru Legacy

1 Answer

I have a 1997 Cavalier thats a 2.2 and its running really rough.


sounds like it may have a bad ignition miss. check spark plugs, wires, and coil packs.

Feb 27, 2009 | 1997 Chevrolet Cavalier

1 Answer

Cj7 w/15cid 4-cyl running bad after tuneup?


i had this problem with my cherokee your not getting the right fuel mixure

Aug 18, 2008 | 1985 Jeep CJ7

1 Answer

Running really rough


Spark plugs, Ignition wiring, ignition coil, or high tension cord may be faulty. They must be inspected one by one and replaced if necessary.

Jul 06, 2008 | 1999 Hyundai Accent

Not finding what you are looking for?
1997 GMC Jimmy Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...