Question about 1996 Plymouth Grand Voyager

1 Answer

Crankshaft position sensor

Where is the crankshaft position sensor located on a 2.4 Engine 1996 plymouth voyager

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 186 Answers

On the transmission bell housing on backside of engine nearest the fire wall.

Posted on Aug 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the pcm located on the plymouth voyager 1996


Hi there:

On 1996 Plymouth Truck Voyager 2WD 3.3L MFI 6cyl the ECM (Engine Control Computer) is located under hood, driver side, front side of strut tower, mounted on inner fenderwell.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Nov 23, 2012 | 1996 Plymouth Grand Voyager

1 Answer

Location of crankshaft sencor on 1996 plymoth voyager 3.3 motor


Look under the hood on drivers side, down near lower part of engine where it meets transmission/transaxle and it should be mounted on top of transaxle/transmission.

Jun 22, 2011 | 1996 Plymouth Voyager

2 Answers

Can u please give me an idea where is the crank shaft sensor really located at on a 98 dodge plymouth voyager


3.0 3.3 and 3.8 liter engines look down on the back side of the engine on the firewall side. It will be under the crossover exhaust pipe and bolted to the transmission. It will have three wires going to it.

Dec 08, 2010 | 1998 Plymouth Voyager

2 Answers

I need to put a crankshaft sensor but I don't Know its location I already changed the cam sensor. Ronnie


The crank sensor is located on the engine near the flywheel axis of the crankshaft.

Crankshaft Position Sensor Removal & Installation To Remove:
Location of the crankshaft position sensor on the 2.4L engine 90904g51.gif
Location of the crankshaft position sensor on the 3.0L engine 91154g20.gif
Location of the crankshaft position sensor on the 3.3L and 3.8L engines 91154g21.gif
NOTE: On the 2.4L engine, the crankshaft position sensor is mounted to the engine block behind the alternator, just above the oil filter. On the 3.0L, 3.3L and 3.8L engines, the crankshaft position sensor is mounted on the transaxle housing, above the vehicle speed sensor.
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect the crankshaft position sensor electrical connector.
  4. Unfasten the sensor mounting screw, then remove the sensor from the vehicle by pulling it straight out.
To Install:
NOTE: If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face.
  1. Install sensor and push the sensor in until contact is made. While holding the sensor in this position, install and tighten the mounting bolt to 105 in. lbs. (12 Nm).
  2. Connect the crankshaft position sensor electrical connector.
  3. Lower the vehicle.
  4. Connect the negative battery cable.
prev.gif next.gif

Jul 31, 2010 | 1996 Plymouth Grand Voyager

2 Answers

Where's the crankshaft position sensor located in 98 plymouth voy


Guessing it's a 6 cyl, 3.0L, but should be located on transaxle housing above vehicle speed sensor.c937fe4.jpg

Aug 31, 2009 | 1998 Plymouth Voyager

2 Answers

How to test a CRANKSHAFT POSITION SENSOR


Unplug sensor connector,using a digital volt ohm meter set on ac volts position.Connect the leads to the two pins in the connector of the crank sensor.Then have a helper crank engine over.You should see ac voltage,if not,then your crank sensor is bad.

Aug 06, 2009 | 1996 Plymouth Grand Voyager

2 Answers

Where is the crankshaft position sensor


Its on the engine block pointing towards the crankshaft at the one side facing the firewall in most cases

May 25, 2009 | 1997 Plymouth Voyager

1 Answer

Two codes...need the actual physical location of oxygen sensors


pop the hood and look behind the engine in the middle....you'll see o2 sensor on the top of the exhaust pipe unplug it and remove it ............second o2 sensor is located on the same pipe under the passanger seat under the car

Mar 04, 2009 | 1996 Plymouth Grand Voyager

1 Answer

Crankshaft position sensor


Here you go:
Fig. 3: Crankshaft position sensor (1) is located next to the oil filter (2) on the 2.4L engine
7cf6b9b.jpg

Aug 29, 2008 | 1996 Oldsmobile Achieva

Not finding what you are looking for?
1996 Plymouth Grand Voyager Logo

377 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...