How do I remove plastic panel at bottom of Ed22TQ

for passenger side:
1. unclip screw cover 'center flap' of inside door opener plastic cover, flap is 3/8"x 3/8" (center of plastic cover)
2. remove phillips screw now showing
3. push fabric panel (edge of door opener plastic cover-at hinged end of chrome handle) to allow uncliping of edge of plastic cover (top rt & lwr rt (for passenger side) of plastic cover)
4. open chrome inside door handle to allow plastic cover to be removed-slide plastic cover toward rear, free end of door to remove cover
5. remove switch panel-gently pry with wide non maring pry bar (cover wide blade screwdriver using cloth) do rear of sw panel 1st (don't pry front edge)
6. slide switch panel toward rear to allow removal
7. remove large phillips screw under sw panel
8. remove the 2 plastic covers near top, hinge edge -use plastic spoon handles to encourage caps to pop off. May also require small screwdriver approx 1/8" in to complete pop off
9. remove the 2 phillips screws w/ captive washers
10. remove 3 phillips/hex screws along the bottom inside of door panel
11. on outside/rear edge of panel push the 2 center pins of each in about 1/8"-this allows the clip to be pulled out w/ pin pushed in
12. remove plastic cover (REAR OF SIDE MIRROR)-pull window edge up and back.
13. lift rear of door panel (not hinge edge) up allow hinge edge to pivot around lower pin in door (hinge edge)
14. remove the 2 rt edge "L" brackets (gently pry center plastic pin out) (note the color and replace as removed)
15. slowly peel the clear plastc away from the non hinged end to expose the plastic panel with 3 phillips head screws
16. remove the 3 screws and panel for access to door handle.
17. using access area now available unlatch the rod attached to exterior door handle (unclip plastic to rotate clip up to allow rod to slide out-toward hinged edge)
18. using access area now available remove rod from ext door handle from inside door area
19. remove the 3 -10mm head bolts
20. remove the ext door handle (bottom edge out first)
reverse order to replace door handle

Trim and molding remove tool and a phillips screw driver
Drivers Side

Remove
Door trim panel and water shield (top where window is)
Plastic panel around door handle. snaps out
1 screw upper front extension assembly (plastic triangle)
2 screws located lower bottom left (drivers side) and door trim panel
Use remove tool to push out retaining 'C' clip behind door handle
Grasp panel where opening are and pull up and out gently
Now disconnect wire harness

There should be at least one screw holding the door handle trim piece. And check for other screws, like on the door pull or armrest, may be hidden behind small rectangular or square caps or plugs that are pried off to reveal the screws. The bottom and up the sides of panel should be held by plastic pins that push in to secure. Use a putty knife or screwdriver under the panel at bottom to pry the pins out. Work carefully all around trying not to break any of the plastic retainers (although they can be replaced if broken. When all free of the plastic retainers, pull panel out from bottom and lift up and away from the window channel. Unplug any electrical connections, and panel should be free.

All there is is just screws around the outer sides of the door panel(3 on bottom). There is one located on the arm rest where the handle is. Then you need to take the screw out where you can lock your door and open your window ect... And just move the panel around until it comes off. You might have to pull the door opener out a little to get it through that hole.

1. You have to unscrew the 3 screws. 2 at the bottom of the panel. One is located inside the door light just pop the cover off to get to it. One is located at the egde of the door panel where you open the door. One is located at the very bottom of the panel.
2. Once screws have been removed: remove the plastic trim from around the door handle. Just a small plastic piece that snaps in around the door handle.
3. Once thats done just left striaght up. Panel should slide off the plastic clips.

first remover the trim ring from around the inside door handle by using a flathead screwdriver between the 2 plastic pieces at the top and bottom of the trim ring and it should pop off ,then take the 2 screws out of the arm rest,then pop the plastic piece off by the mirror mount by pullin out on it then just work your way around the panel with the screwdriver and pull the door panel away from the door,there are just plastic clips that hold the panel to the door,after that just unplug the window switches once u have the panel off the door,hope this helps

you have a bad solder joint in your heater control head. If you can solder, you can fix it. I will fix it for $25 and send you a control head. Then you send yours back to me.

Here's our Villager/Quest web site.

http://groups.yahoo.com/group/villagerquest/links


You have to remove 4 plastic screws on console bottom. Then remove 2 screws at bottom of center trim panel. Then remove ash tray and 2 screws just above tray opening. Then 2 screws at top of center trim panel. Then pull off center trim panel. It has 2 spring clips in center.
Then remove 4 screws holding control head in.
Remove all electrical connectors.
remove thin plastic cover on bottom of unit. 2 plastic clips hold it on.
remove circuit board, and look on back side for crack around solder joint that is circled in red on picture. Or the joint next to it.
resolder the cracked joint. Don't heat the joint too much. Just enough to get solder to drop on to it.

To Remove Door Panel on 2001 Honda Accord:

A: To remove the plastic piece with the door lock button and door handle connected to it:

1- Remove the screw in the middle located behind a plastic cover button
2- Push (slide) the whole assembly Forward (toward front of car)
Besides the screw, it is held in place by 3 hooks on the backside that hook into holes in the metal door frame
3- Now unhook handle from small metal bar going through door by pushing (toward door) plastic clip (blue?) off of the bar, then the bar will come out of the clip hole, thus releasing the handle.
4- Depress little grey button /bar (purple painted on it)on elec. connector to seperate connector, thus releasing door lock switch

Now the whole assembly (metal handle, door lock switch, and plastic piece) will come off door panel

B: The door is held on by 2-screws, 7-plastic snaps/plugs, and 1-plastic plug.

The screws are located: bottom of hand hold and the other behind the handle, both covered by little covers that have to be pryed off to access the screws.(hint: the screw with the built in spacer goes behind the handle when you are trying to reinstall)
The 7-plastic snaps: 3 across bottom and 2 on each side. Not visible, they are mounted to the inside of the panel.
The 1-plastic plug is visible at the upper front of the panel and is the same color as the surrounding trim


C: Take off the big plastic triangle piece above the door panel and behind the mirror. Pull/pry off. It has 2 snaps holding it on. one near bottom and one near the front.

D: Light lens prys off from bottom. Unscrew (1/4 turn) the light assembly with bulb still intact from backside of panel

E: Remove the Hand-Hold/window switch assembly:

IF you scroll over the title, you can see the word "window". Raise the window about two inches. Remove the interior door panel: Remove the inner door handle screw, push the handle forward, pull it out some, unclip the actuating rod, you may also have to unplug the power lock switch. Remove the screw in the arm rest. Remove the plastic plug at the forward upper corner of the panel. Remove the black plastic triangle at the insdie of the side view mirror (it just snaps in place). Pull the bottom of the panel away from the door to disengage plastic clips, then lift the panel off the door and disconnect the electrical connectors. Pull the plastic away from the bottom part of the door (you'll probably end up tearing it). There are two bolts that hold the window glass to the regulator mechanism, remove those and the glass can be pulled up through the window opening. If necessary, the bottom of the window tracks (a screw at the bottom of botjh) can be loosened to loosen up the window.

Remove the plastic screw covers at the forward edge of the door. Remove the 2 gold coloured screws.
Using a flat blade screwdriver, insert the blade above & below the locking thing at the door handle, pry up and down, top & bottom respectively. Slide & pull the handle out, remove the rod going to the handle.
Remove the 2 big screws for the door panel. 1 is under a small trim cover, the other is under the armrest
Remove the lower light & unplug it (if you have one) which may be under the arm rest (it pops out)
Press the centers of the 2 round push clips that are on the rear edge of the door panel and pull the clips out
Remove any screws at the bottom of the door panel (if you have them)
Starting at the bottom of the panel pull straight out with steady, even pressure as to not snap the plastic clips. After the bottom & side clips are disconnected from the door, lift the top of the panel straight up.
Remove the plastic sheet that covers the inner shell of the door.
Uning a 10 millimeter socket, remove the bolts that holds the window onto the regulator
Remove the window, up & out thru the top of the door
Unbolt & replace the regulator.