Location of the valet/override button on a 1999 durango

If there is such a button the location and method of operation will be found in the vehicle handbook.

Try this Instructions

1. • 1Press the "Unlock" button on the remote keyless entry device.
   • 2 Insert the key into the ignition. Turn the ignition switch to "ON" without starting the engine.
     
   • Sponsored Links
     
     • Powerpoint To VideoDownload Videos To Your Desktop & Convert To Any Format - All Free!
       www.videodownloadconverter.com
   • 3 Press and hold the valet/override button below the steering column within five seconds of turning the ignition on.
     
   • 4 Release the valet/override button when the security light on the instrument panel stops blinking. The alarm is reset and disabled.
     

Read more

the
valet/overide button, found under the
dash area

1. 1 Insert the key into the ignition.
2. 2 Turn the ignition switch to "ON." Do not start the engine.
3. 3 Press and hold the valet/override button within five seconds of turning the ignition on. The valet button is located beneath the steering column.
4. 4 Release the valet/override button after the security indicator light turns off.
5. 5 Turn the ignition switch off.

The valet/override button is located right under the steering column on your 1999 Dodge Durango. To reset the alarm, press and hold the button within five seconds of cranking up the engine - release it when the security lights stop blinking.

The 2000 Dodge Intrepid is equipped with an alarm system that is triggered when unauthorized entry is attempted. In some situations, such as having the Intrepid valet parked or when it is being serviced by a mechanic, the alarm system needs to be disarmed so it doesn't go off. Disarming the alarm will prevent it from being activated until it is armed again.
Difficulty: Moderate Instructions

1. 1 Insert the key into the ignition.
   
2. 2 Turn the ignition switch to "ON." Do not start the engine.
   
3. 3 Press and hold the valet/override button within five seconds of turning the ignition on. The valet button is located beneath the steering column.
   
4. 4 Release the valet/override button after the security indicator light turns off.
   
5. 5 Turn the ignition switch off.
   

have to do it in this order

Your black ended driver key should open the glove box. The valet key is not made to open it, thats the safty feature in it. There is no overide for the Valet settings, you have to unlock the glove box with Driver (master or black) key and turn the Valet switch off. Also the Valet switch does not engage the glove box lock so over riding the Valet security wouldnt open it even if you could over ride. If the Valet key would unlock it or was easy to overide then it wouldnt be a very good safety feature. Best of luck, hope you can get it opened.

Hi there. As far as the valet/overide button, it's a hidden
device-switch, a little spring loaded micro button,
red or black possibly and is probably down under
the dash area, near your knee/leg. In some
remote start/alarm combos, the antenna on the window
glass will also have an override/valet button.
Older sytems will have a flip type toggle switch.

When you locate the button or switch,
turn on the ignition key, press and hold
in the button until the alarm chirps 1 time
(for toggle types, key on, flip switch in the
opposite direction, then key off). This should over ride the system. You would get a single chirp to confirm from the siren.
The LED (light emiting diode) light in the dash
should also go on solid. This is valet/overide/reset.
This should correct any issues like starter disable,
or anti-hijack. Your keyless entry, if installed,
will still be operable. The have it inspected for the
falsing issues you are experience at a local shop.
You would repeat the same steps to toggle back into user mode.