Question about 2001 Mazda 626

1 Answer

Is there a bearing inside the intermidiate support for the cv axel on a 2001 mazda 626

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 157 Answers

Yes

Posted on Oct 31, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How 1996 mazda 626 front axle shield broken


The drive shaft has to be removed to replace the rubber boot .you will have to dismantle the CV joint , clean and repack the joint with special grease and fit a new boot.

May 10, 2014 | 2001 Mazda 626

1 Answer

Knocking sound drivers side front during exceleration


Have the CV joints checked on the front axle shaft ends. When they wear out they knock on acceleration.

Mar 21, 2014 | 2001 Mazda 626

1 Answer

Cant get bolts out of cv axel support braket in a mazda 626


This is a bracket mount that has the axle shaft going thru it on the passenger side . the axle must be removed from mount before it can be removed . there is a single bolt that presses against the axle shaft bearing and a snap ring that holds the bearing in the mount once removed the axle will slide out .

Mar 21, 2014 | 1997 Mazda 626

1 Answer

94 mazda 626 cv shaft removal


Stick a large screwdriver or prybar between the CV housing and the transmission case, and pop it out. There is a little circlip in a groove near the end of the shaft inside the transaxle. It is there to seat the shaft and prevent it from slipping out during driving.

Feb 24, 2012 | 1994 Mazda 626

1 Answer

After having cv joints replaced on my 99 mazda 626 there's a loud roaring while driving. What is the cause of the roaring?


The noise you are describing may very well a bad wheel bearing, the wheel bearings are sealed units and they last about 100,000 miles on average, the fronts go 1st because they carry the heaviest load.

Nov 01, 2011 | 1999 Mazda 626

1 Answer

Mazda 626 popping noise in front driver side when turning and or body shifting


Your Constant velocity joints have gone bad. the Boot that holds th grease has leaked out all the grease and the bearing inside are not being lubicated and thats where the poping comes from. Have someone look at the axle (CV) to determine if repairable or you might have to replace the axle. Hope this helps

Jun 27, 2009 | 2000 Mazda 626

1 Answer

How do I replace the front wheel bearings on a Mazda 626 1998


The front bearings on a mazda 626 are sealed and you must remove the entire hub assembly to have a shop or dealer install the bearings. The hardest part is you need to remove the center axel nut and it is very tight and is called a stake nut. If you do not have a fairly good amout of skill at repairs, this is one job that is safest left to the pros. Just one missed step can create more damage than you could beleive.

May 20, 2009 | 1998 Mazda 626

2 Answers

Clicking sound when turning hard or in reverse turning....


Usually that is the sign of a cv joint going. I have an accord with front wheel drive and it did the same thing. THe cv boot being torn could have caused the initial breakdown of the bearing faces...

Mar 27, 2009 | 1995 Mazda 626

1 Answer

Mazda rustler 160i wheel bearings


a had sabe problem in a same model about one year.
i replaced inner and outer cv joint

Dec 03, 2008 | 1997 Mazda 626

Not finding what you are looking for?
2001 Mazda 626 Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...