Question about 2001 Chevrolet Silverado 2500HD

Open Question

Steering wheel will not lock 2001 2500hd after changing out the multi function switch, everything else work, but will not lock with key off

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 337 Answers

SOURCE: changing key ignition need to remove old one and fix ignition rod

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008f60e

Posted on Dec 01, 2008

Ad
  • 1 Answer

SOURCE: Steering wheel locked.. can't move key ...

I had the same problem , I tried all sorts of jiggling didn't work , a mate came over and rocked the steering wheel left to right, while trying to turn the key ( But) while trying to turn the key, keep pulling the key out of the lock by small increments . This worked for us . when it happened to ours it was like the key was going in too far . Hope that helps . Kev

Posted on Mar 10, 2009

  • 14036 Answers

SOURCE: 2001 chevy sylverado 2500hd power steering and power brakes quit

check power steering fluid. first. if all good . power steering is going. your hydro boost brake system depends on the power steering pump if it goes out your brake go out.

Posted on Mar 29, 2009

DAD5bbbbg
  • 111 Answers

SOURCE: my ignition switch is either locked or frozen?

Try to pull your steering wheel hard both ways left first then right and try to turn your key at the same time.as you are pulling on the wheel

Posted on Apr 08, 2009

  • 1 Answer

SOURCE: ignition cylinder won't turn

I had the same problem in a 94' trooper. Basically the Ignition lock cylinder is wore out and you need a new one. Mine wouldn't turn past lock and no matter what I tried it wouldn't turn. You can go on auto zone and find the part, mine was about 61 bucks, it comes with keys and the ignition cylinder. The deal is that to get your new ignition cylinder in you have to get your original turned to off or acc I can't remember. You'll see with your new ignition cylinder that when you turn the key there is a button that can be depressed but only when the key is turned past lock and it also won't depress in start. First, disconnect battery and wait like 30 minutes. So, what you do is take a screwdriver handle and place it up against key and take some pliers or something and beat on it a couple of times, this gets the key in deep enough to where you can eventually turn it. I swear it will eventually turn, once there, take off the top and bottom plastic covers off steering wheel/unscrew electrical wires on back of ignition cylider and other side and you know the button I referred to basically you have to depress that with key in acc or off and it will slide out. If your having trouble finding the button look at new ignition cylinder in comparison to old one and you can see where the depressed button is on side closest to you, you'll see a little hole up on the side of housing that you can depress.

Posted on Apr 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I replace turn signal switch


Multi-Function Switch Removal
  1. Disconnect the battery ground cable.
  2. A Remove the ignition switch lock cylinder. B Insert the ignition key into the ignition switch lock cylinder and turn to RUN position. C Push the ignition switch lock cylinder release tab with a punch while pulling out the ignition switch lock cylinder.
  3. If equipped, twist the tilt wheel handle and shank counterclockwise and remove.
  4. A Remove the upper and lower steering column shrouds. B Remove the screws. C Remove the upper and lower steering column shrouds.
  5. A Remove the multi-function switch. B Remove the screws. C Disconnect the electrical connectors. D Remove the multi-function switch.
Re Install:
  1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 10 mi or more to relearn the strategy.
  2. To install, reverse the removal procedure.
#2 Illustration
    swn~us~en~file=gj0898a.gif~gen~ref.gif
173025f0-1240-465d-93ea-d1d3903e9e1b.gif

#3 Illustration

05c73e9d-2c3c-4f4d-b94e-113d4d19c054.gif

#4 Illustration

1628f332-eb34-4013-b9c5-00caaeea5a5b.gif

#5 Illustration
b1959cf9-5d5f-4686-871a-f2bdf070027a.gif

Re-install

4bf17f23-231c-4231-b48e-cb2ff186ac56.gif

Sep 22, 2014 | 1998 Ford Explorer

2 Answers

Highbeams work, low beams do not. wipers only work when highbeams are on. highbeams work but only when you HOLD the turn signal lever towards the steering wheel. all other lights work. relay switch or...


The problem is most likely your cars multi function switch. That is the switch that controls your blinkers, dimmer, and everything else. If you change the switch that should solve your problem.

Sep 11, 2011 | 1990 Volkswagen Cabriolet

1 Answer

Replace turn signal switch


Ensure lever is in center of off position.Disconnect negative battery cable. Disable airbag system. Remove steering wheel. Remove lower and upper column covers. Remove lock cylinder if necessary. Remove wiring harness strap. disconnect steering column electrical connectors. Disconnect turn-signal and multi-function switch Gray and Black connectors. Remove turn-signal and multi-function switch from vehicle.

Jun 05, 2011 | 1998 Chevrolet K1500

1 Answer

Need to replace ignition cylinder. no keys


This is not an easy repair due to anit theft requirements. need to chisel off bolts.

Section 11-04: Steering Column 1997 Probe Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000
Ignition Switch Lock Cylinder Removal
  1. Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Remove the four lower steering column shroud screws.


    j5021c.gif

  1. Separate the upper and lower steering column shrouds.
  1. Remove the ignition switch lock cylinder illumination miniature bulb from the lower steering column shroud.
  1. Remove the upper and lower steering column shrouds.
  1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal and installation procedure.
  1. If equipped, remove the ignition/shifter interlock cable screw.
  1. Disconnect the ignition/shifter interlock cable (3F719) from ignition switch lock cylinder (11582).
  1. Use a chisel to remove the two ignition switch lock cylinder bolts.
  1. Remove the ignition switch lock cylinder from the steering column.
  1. Disconnect the ignition key reminder switch electrical connector.
  1. If necessary, remove the ignition key reminder switch.


    j5028b.gif

Installation
NOTE: Use new ignition switch lock cylinder bolts. Tighten the bolts until the bolt heads break off. Check for proper ignition switch (11572) operation.

To install, reverse the removal procedure.

Mar 25, 2011 | 1997 Ford Probe

1 Answer

What are the instructions to remove and replace the combo turn signal switch, located in the steering column, for a 1999 bravada


Warning: 1995 and later models are equipped with an airbag. Always turn the steering wheel to the straight ahead position, place the ignition switch in Lock and remove key, then remove the airbag fuse and unplug the yellow Connector Position Assurance (CPA) connector at the base of the steering column before working in the vicinity of the impact sensors, steering column or instrument panel to avoid the possibility of accidental deployment of the airbag, which could cause personal injury. The yellow wires and connectors routed through the instrument panel are for this system. Do not use electrical test equipment on these yellow wires or tamper with them in any way while working under the instrument panel.
Caution: On models equipped with a Delco Loc II anti-theft audio system, be sure the lockout feature is turned off before performing any procedure which requires disconnecting the battery.

  • The turn signal switch function is incorporated into the multi-function switch, along with the wiper/washer and headlight dimming controls.
  • Disconnect the negative battery cable. Remove the steering column covers and the drivers knee bolster.
  • Remove the two Torx screws securing the multi-function switch to the top of the steering column.
  • Clip the wire-ties securing the multi-function switch harness to the other steering column wires.
  • At the bottom of the steering column, remove the bolt securing the large bulkhead electrical connector to the firewall.
  • Separate the two multi-function switch connectors from the large bulkhead connector.
  • The multi-function switch and its harness must be replaced as a unit.
  • Installation is the reverse of removal

Mar 16, 2011 | 1999 Oldsmobile Bravada

1 Answer

Both headlights quit working simotaneously


There are just (3) possible reasons for this:
(a) your headlight switch has failed, or
(b) your headlight relay has failed.
(c) Fuse 1 (25 Amps) has blown

The headlight relay and fuse 1 are located (I think) in a fuse/relay block under the hood.
The headlight switch is part of the "Multi-function Switch" on the steering column.

Here's how to replace the 2001 PT Cruiser multi-function switch:

archaeology_27.jpg
Multi-Function Switch Removal & Installation
1. Open the hood.
2. Disconnect and isolate the battery negative cable.
3. Remove both upper and lower steering column shrouds.
4. Disconnect both posi-lock harness connectors at the rear of the multi-function switch.
5. Remove multi-function switch mounting screws and remove switch from vehicle.




To Install the new multi-function switch:

Note:
If replacing the multi-function switch, the combination flasher and windshield wiper/washer switch
must be transferred to the new multi-function switch.

1. Remove the two Torx(R) screws retaining the wiper/washer switch, place next to the new
multi-function switch and install two screws.
2. Place switch into place and install mounting screws. Torque multi-function switch to column
retaining screws to 27 inch-lbs. (3 Nm).
3. Connect both posi-lock harness connectors at the rear of the multi-function switch.
4. Install both upper and lower steering column shrouds.
5. Connect the battery negative cable.
6. Close hood.
7. Verify vehicle and system operation.

Mar 15, 2011 | 2001 Chrysler PT Cruiser

1 Answer

How do I replace the turn signal multi-function switch in my 1998 Ford Expedition


SECTION 211-05: Steering Column Switches 1998 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/11/2000 Multifunction Switch Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the ignition switch lock cylinder (11582).
    1. Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
    1. Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.
    gj0845a.gif
  1. Twist the tilt wheel handle and shank (3F609) and remove.
    gj0846a.gif
  1. NOTE: Move gear selector to lowest position to access steering column opening cover.
    Release the four clips and remove the steering column opening cover.
    gj0847a.gif
  1. Remove the upper and lower steering column shrouds.
    1. Remove the three screws.
    1. Remove the lower steering column shroud.
    1. Remove the upper steering column shroud.
    gj0976a.gif
  1. Remove the multi function switch.
    1. Remove the two screws.
    1. Disconnect the electrical connectors.
    1. Remove the multi function switch.
    gj0848a.gif
Installation
  1. NOTE: When the battery (10655) is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
    To install, reverse the removal procedure.
    gj0850a.gif

2010&c18=modelyear&c20=n130593&c35=wsm%2cmultifunction%20switch%2cswj%2c211-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 08, 2011 | 1998 Ford Expedition

1 Answer

How do you change an ignition switch on a 2002 VW beetle


This is for the requested item:

Removal & Installation
  1. If necessary, make sure you have the radio code.
  2. Place the steering wheel in the center (wheels straight ahead) position.
  3. Disarm the SRS system, as outlined in the Chassis Electrical System.
  4. Make sure the negative battery cable is disconnected.
  5. Remove the steering wheel, as outlined in this section.
  6. Remove the upper and lower steering column switch trim. Refer to the Turn Signal (Combination) Switch or Multi-function switch procedure for details.
  7. Disconnect the multi-pin connector from the ignition/starter switch.
  8. Remove the locking fluid (paint) from threaded holes of screws.
  9. Loosen the two screws slightly, and pull ignition/starter switch out from steering lock housing in direction shown.

d997782.gif
Remove the locking fluid (paint) from threaded holes of the screws (A). Loosen the two screws (A) slightly, then pull the ignition/starter switch out from steering lock housing in direction of the arrow


To install:
  1. Push the ignition/starter switch into steering lock housing.

    NOTE When installing the ignition/starter lock switch ensure that the ignition/starter lock switch and the lock cylinder are in the same position, e.g. "ignition on".

  2. Tighten screws and seal securing holes with sealant D2.
  3. Connect multi-pin connector to ignition/starter switch.
  4. Install steering column switches, steering wheel trim and steering wheel, as outlined in this section.

Mar 06, 2010 | 2003 Volkswagen New Beetle Convertible

1 Answer

How do I install headlight switch on 95 mercury tracer?


  • Headlamps Inoperative
  • Fuse.
  • Headlamp switch.
  • Headlamp relay.
  • Circuit.
  • Bulbs.

Section 11-05: Steering Column Switches 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Multi-Function Switch
Removal
  1. stf~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE ELECTRICAL CIRCUIT NECESSARY FOR AIR BAG DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY GROUND CABLE MUST BE DISCONNECTED PRIOR TO SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS.
    Disconnect the battery ground cable (14301) and wait one minute for the backup power supply to be depleted.
  1. Remove the steering wheel (3600). Refer to Section 11-04 for the removal procedure.
  1. Remove the four screws from the lower steering column shroud (3530).




  1. Remove the ignition switch lock cylinder illumination lamp socket from the lower steering column shroud.
  1. Remove the lower steering column shroud.
  1. Remove the upper steering column shroud.
  1. Disconnect the three multi-function switch electrical connectors.
  1. Remove the multi-function switch screws.
  1. Remove the multi-function switch electrical connectors and the multi-function switch (13K359).

Jan 16, 2009 | 1995 Mercury Tracer

2 Answers

2000 Toyota Camry - car ignition seems to be jammed or keys worn - has a transponder key just won't turn


What you have is the anti-theft portion of the steering column has became engaged. When you remove the key from the ignition, there is a pin that retracts, and, when the steering wheel is turned, this pin enters a hole in the column's steering shaft. This prevents the car from being "steered" if someone defeats the ignition switch, while trying to steal it. This locking function will not happen if the car is parked with the front wheels straight ahead; the only time the locking function occurs is when the steering wheel is turned left or right, as in parking whilst turning the steering wheel. This is a normal occurrance, the locking of the steering wheel, as it denies steering to potential theives.
SOLUTION: When the key will not turn, try to turn the steering wheel to the left of right (whichever way it is "turned" to), and, simultaneously, turn the key in the ignition. The "turning" of the wheel relaxes the tight fit of the pin into the hole, and then the key will turn, as it retracts the locking pin from the hole in the column. Hope this helps; and thank you for choosing FixYa!

Oct 12, 2008 | 2002 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...