I need a color code for the ignition switch for an 09 Dodge Journey. Trying to install a keyless entry & remote start system.

SOURCE: keyless entry remote

Check inside the remote case...there's instructions printed that tell you to hold the lock and unlock buttons for 7 seconds to reset the remote. I'm in the middle of replacing batteries myself. Let me know if it works.

SOURCE: remote keyless entry not working

How can I re-syncronize the remote keyless entry system on my year 2000 Honda Accord

ZappaNut

• 960 Answers
• Posted on Dec 15, 2008

SOURCE: reprogram keyless entry system

1991-94 Nissan Maxima key less entry reprogramming procedure:

1. Enter the *original code found under the dashboard.
(*the code begins with the letter F and has 7 digits)

2. Close the doors and lock all of the doors,
enter the 7 digit code ( make sure you have your key in hand).

3. Once the code is entered correctly you will hear a long beep ♪ ♫.
While the beep ♪ ♫ is sounding ... ENTER your NEW 4 digit code, (you will then hear random beeps ♪ ♫)
Do not touch anything until the beeping ♪ ♫ stops.

4. To open the doors, the front windows and the trunk,
type: S(Clear) and the New 4 digit code and the door will open automatically.

5. IF by any chance you forget your new code. Just enter the original one and start all over.

SOURCE: Program factory remote keyless entry: 2003 Hyundai XG350

The procedures you list require the Hyundai Keyless Remote programming module, which you don't have. This module is proprietary - only Hyundai Dealerships have it. There is a 10 pin connector under the dash (next to the DLC - Data Link Connector) which is used to connect the Keyless Remote Programming Module. This module has two switch positions "Ready" and "SAVE". When the switch is place in the 'SAVE" position, that's when the keyless remotes are activated to send their 'codes' to the Electronic Time and Control System (ETACS). The module's switch is then set to "Ready" and the remote is tested to see if it works properly.

SOURCE: program factory remote keyless entry for 2003 Hyundai XG350

This bulletin supersedes TSB# 02-90-001.
DESCRIPTION: The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03
or newer) and Data Link Connector (DLC) Cable. SERVICE INFORMATION: The keyless adapter cable can be used on the following vehicles:

• 2001 - 2004 MY Elantra
• 2001 - 2004 MY Santa Fe
• 2002 - 2004 MY Sonata
• 2001 - 2004 MY XG300/350

• The 2003 - 2004 MY Tiburon does not need the Keyless Adapter Cable to add keyless entry remotes to the factory security system. Instead, the Hi-Scan Pro connects to the vehicle using only the DLC cable. See page BE-60 in the 2004 MY Tiburon Shop Manual for the latest instructions.
• The most current Keyless Adapter Cable Instructions are available in the following shop manuals:

1. Connect the keyless adapter cable to the Hi-Scan Pro DLC cable.
2. Plug the keyless adapter into the vehicle's 10-pin multi-purpose connector located behind the driver's side lower instrument panel (next to the DLC). NOTE Sample vehicle shown is the Santa Fe.
   
3. Turn the Hi-Scan Pro ON
   and press ENTER
   . NOTE "Release date 29. Sep. 2003" OR LATER
   must appear on this screen. To update your SOL card with the latest software go to www.hmaservice.com and refer to TSB 00-00-001.
   
4. Select option "HYUNDAI VEHICLE DIAGNOSIS"
   and press ENTER
   .
5. Select vehicle model and press ENTER
   .
6. Select option "TRANSMITTER CODE SAVING"
   and press ENTER
   .
7. Ensure that the key has been removed from the ignition cylinder before proceeding.
8. Follow the steps noted on the Hi-Scan Pro screen to program the remote(s). NOTE The factory security system can only be programmed to accept two remote transmitters and MUST be programmed for both remote transmitters at the same time.
   
9. Press ESC
   on the Hi-Scan Pro and verify that the remote(s) are functioning properly.
10. Turn the Hi-Scan Pro OFF
    and disconnect the adapter cable from the multi-purpose connector.