Question about 2000 Chrysler Sebring

2 Answers

My car would not start, i would drive pretty wellthen all of a sudden the engine would not turnover. The panel lights, AC, everything comes on except the engine turingover. I towed it to a mechanic, that re-grounded some wires, it worked but now i am having the same problem again

Posted by on

  • 1 more comment 
  • moneyrashad Aug 02, 2009

    the garage did not have to jump start the battery, he said he regrounded some electrical wires. i thinking it maybe my starter or some electrical short. how would i reground my engine? i want to see if it is somthing i can fix myself before i take it back toa garage

  • moneyrashad Aug 02, 2009

    can you help me

  • moneyrashad Aug 02, 2009

    a little

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 19,396 Answers

Tell the mechanic to scan the ECU (main computer module) to see if there are codes stores in there.

Problems that happen erratically are difficult to troubleshoot, often they are related to wiring problems.

Scan the computer, that can tell you in which area the problem may be.

Posted on Aug 02, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,341 Answers

If the garange jump start it and then it starts ,then it's your battery which either is not charging up or not holding charge.It may be the altenator not charging up,If now the car needs to be pushed and engaged in gear before starting then you need to check the starter motor.It all depends which one applies to you here.

Posted on Aug 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I start my 2001 hyundai elantra my engine vibrates I turned it off restarted and it did it again I put my hood up everything seem to run right except for one of my belts pop ac belt maybe start...


It sounds like the idle speed is set too low, and it is taking the PCM a few moments to figure the correct setting. If the engine is new, or new to the vehicle, perhaps the engine idle speed setting is incorrectly set too low.

Apr 15, 2014 | Cars & Trucks

1 Answer

Rpm fluctuate and oil light comes ON


First I would check your oil level in your engine

Jan 01, 2014 | Holden Astra Cars & Trucks

1 Answer

No dash lights when headlights are turned on. Everything works fine on my vehicle EXCEPT today the panel lights don't work. Turn signals, hazard blinker, oil gauge, rpm gauge, speedometer, drive shift...


there is a regulator for the display brightness, you may have it turn'd down or it has stopped working;. it controls the brightness at which the dash lights are. usually has a speedo sign on it. goes up and down. it works with the main light and is conecter to them on the same lighting board if it has gone then a new light swtch control switch will be needed.

Oct 13, 2013 | 2001 Chrysler Town & Country

1 Answer

My 2001 Hyundai Santa Fe's check engine light came on recently. I believe it is related to the fact that when I put on the air conditioner, the car's driving becomes really jerky. It accelerates, but...


If you could tell me the code (diagnostic trouble code - DTC) stored in the Engine Computer (ECU), I might be able to help. Find an OBDII scanner & retrieve the code (or codes) stored in the engine's control unit (ECU). Write them down & let me know what/which code(s). We can go from there.

Nov 03, 2010 | 2001 Hyundai Santa Fe

1 Answer

2000 jaguar XJR. pressing accelerator - nothing happens -


if its a v8 its gonna be your throttle body its a complete assembly and is a common problem on these models

Apr 11, 2017 | 2001 Jaguar XJ8

1 Answer

Driving down interstate at 70 mph car suddenly


i would start in fuse and relay area with voltmeter.

Dec 05, 2009 | 1994 Nissan Altima

1 Answer

No start


check starter solenoid or relay

Sep 27, 2009 | 2003 Volkswagen Passat

2 Answers

Engine will not turnover


If there is no power coming IN to the starter relay - the ignition module has failed.
Replace the Ignition.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 24, 2009 | 2008 Jeep Wrangler

3 Answers

Engine died while driving..


Hello Friend,
Pull out the spark pugs so, there is no longer compression. Put a wrench on the crankshaft pully. The engine will turn and the pistons will travel up and down. This is of course it the engine hasn't seized. If the engine turns its the starter. Simple.

Jul 17, 2008 | 2005 Toyota Matrix

Not finding what you are looking for?
2000 Chrysler Sebring Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...