Question about 2004 GMC Envoy

2 Answers

Code 106 comes on my 2004 gmc envoy what do i need to do to fix it

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 1,242 Answers

Steve, the MAP is on drivers side next to firewall up top on the I6 engine. You can try cleaning it with sensor safe electrical spray. But I've found this doesn't work, just replace it.

Posted on Jul 06, 2018

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 3,605 Answers

All trouble codes are 5 digits starting with a letter

Posted on Jul 04, 2018

  • Lonte J
    Lonte J Jul 04, 2018

    If the code in full is "PO106" it is in reference to the "MAP" sensor, Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance Problem. The Powertrain Control Module (PCM) uses the Manifold Absolute Pressure Sensor (MAP) to monitor engine load. (NOTE: Some vehicles have a Barometric Pressure (BARO) sensor that is integral to the Mass Air Flow (MAF) sensor and do not have a MAP sensor. Other vehicles have a MAF/BARO and a redundant MAP sensor where the MAP sensor functions as a backup input in case of MAF failure.

    Read more at:https://www.obd-codes.com/p0106
    Copyright OBD-Codes.com
    I hope this helps you in your repair to the problem :o) Jesus loves you, John 3:16-17 (KJV)

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 250 Answers

SOURCE: battery removal on a 2004 GMC Envoy

The battery is on the right side behind the fuse box. You need a metric set to undo the 3 screws. Theres one that attaches to the body, one to the bar that goes along the top, and theres one on the left side below the vacuum hose and air induction. After you've taken out those three, you should lift the whole thing out(battery and shroud) together. It's hard to take the shroud off before you lift the battery out. After that, you have to pry the shoud off the battery. The two terminals in the back make it hard. Then just go to any auto parts store and they'll give you a new one. 

Posted on Jan 28, 2009

ElDopa
  • 295 Answers

SOURCE: E-vac system on fuel tank

P0452 = Generic Evaporative Emission System Pressure Sensor/Switch Low Input.

Since you have a 2004 Envoy, you probably have the dreaded bad 2004 PCM. It is part of the emissions system so it is covered under the emissions warranty (although it's already 2009 and i'm not from the USA, so I'm not aware if that's still applicable).

But in other words: contact your dealer !

Posted on Mar 22, 2009

  • 2 Answers

SOURCE: Speedometer on 2004 GMC Envoy not working. It

There is a recall on the panel Cluster... call your dealer and have it checked out.. mention the recall... www.lemonauto.com

Posted on Jun 05, 2009

  • 85 Answers

SOURCE: Where is the cruise control fuse for GMC Envoy

its in the fuse panel under the hood there should be a chart on the cover

Posted on Feb 24, 2010

jmgldsmth
  • 2005 Answers

SOURCE: 2004 gmc envoy leaking power steering fluid and

replace the leaking power steering hose

Posted on Jul 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0106/po526 code


2 different problems....106 is MAP sensor code, clean your throttle body with the battery disconnected. 526 is fan speed sensor. There is a common problem with the connector that goes into the fan clutch. Check for frayed wires here or burnt connector, if all ok, may need new fan clutch.

Jan 24, 2014 | 2004 GMC Envoy

1 Answer

What does Fuel Level Sensor A Circut High Input for a 2004 GMC Envoy


The fuel level sensor is in the gas tank, and if it needs to be replaced, the tank must be removed from the truck.
Does your gas gauge work correctly? If not, there could be a bad connection at the tank/sensor or the sensor itself is defective.

Jul 05, 2012 | 2004 GMC Envoy

1 Answer

Check engine light on 2004 GMC Envoy. Had air intake sensor replaced. Failed inspection diagnostic code came up P0128. I have been told I needed an air pump, a tune -up, injectors cleaned etc. etc., I have...


Code P0128 indicates a faulty thermostat, more than likely it is always in the open position causing the coolant to come up to operating temperature too slowly.
My suggestion is to find a different repair shop.

Oct 31, 2010 | 2004 GMC Envoy

1 Answer

2004 envoy service engine light stays on. Told


Our mechanic said we need to replace the computer! The cost will be $1,000.

Feb 19, 2010 | 2004 GMC Envoy

1 Answer

Is there a way of turning the key a certain way to display the engine codes on my 2004 GMC Envoy


No, to display fault codes set by the ECU you will need an OBD2 scan tool. This vehicle is OBD2 compliant and that is the only way to access the fault codes.

Nov 05, 2009 | 2004 GMC Envoy

2 Answers

2004 gmc envoy code 0128


This an engine coolant temperature fault, most likely caused by a defective thermostat, probably one that is open all the time.

Jul 17, 2009 | 2002 GMC Envoy XL

1 Answer

2004 GMC Envoy with a P0526 sensor problem


This code indicates a problem with the fan clutch, the speed it is running is not the speed it was commanded to run/ The fan clutch assembly needs replacing.

Jun 03, 2009 | 2004 GMC Envoy

3 Answers

Speedometer on 2004 GMC Envoy not working. It


There is a recall on the panel Cluster... call your dealer and have it checked out.. mention the recall... www.lemonauto.com

Mar 19, 2009 | 2004 GMC Envoy

2 Answers

Loud air sound


If there is an engine code po410 you have problems with your airpump. There are bulletins out on this situation.

Oct 16, 2008 | 2004 GMC Envoy

Not finding what you are looking for?
2004 GMC Envoy Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85020 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...