Question about 2006 Jeep Liberty

1 Answer

How do I get the oil cap off? - 2006 Jeep Liberty

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

Twist it. Righty tighty, lefty loosey.

Posted on Aug 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hello i have a 1998 (s reg) renualt clio grand


how did the oil cap fall off and not get lost? check that the cap doesnt fall off again. if you didnt drive with an engine empty of oil, then everything will be fine.

Nov 03, 2013 | Cars & Trucks

1 Answer

My 96 volvo 850s oil cap leaks oil,can i get a better oil cap than the original one?


There is a replaceable rubber seal in the oil cap. The dealer is supposed to replace it every oil change. The stock ones are around $0.40 and an almost lifetime one is available for $10 from IPD. Are you certain it is the Oil cap leaking from the seal or is the PCV system clogged?
http://www.ipdusa.com/products/5884/115315-ipd-hd-viton-oil-cap-seal

Dec 03, 2011 | 1996 Volvo 960

1 Answer

Where is the oil cap in my 1996 Ford Explorer? I found the dipstick but can't find the oil cap so I can add oil.


its the cap on the valve cover, there is a picture of an oil can on it and it says engine oil unless it has been replaced with an aftermarket cap

May 19, 2011 | 1996 Ford Explorer

1 Answer

Where is oil filter on 2006 hhr 2.2?


Hello, the oil filter location is on the front of the engine, just below the right side of intake manifold.



  • Use a 32 mm (1 1/4 in) socket on the hex on top of the oil filter cap, or an oil filter wrench on the outside diameter of the oil filter cap.
  • Remove the oil filter cap and filter.
  • Remove the filter from the cap.
  • 457bc50.gif

    Oct 24, 2010 | Chevrolet HHR Cars & Trucks

    1 Answer

    1998 Nissan Sentra 1.6 liter.Y oil blowin out of oil fill cap?


    no you will not be the first one to do it
    as long as you copped it and did not run engine without oil should be okay top up to proper level put cap on should be okay
    oil will blow out cap removed normal

    Mar 15, 2010 | 1998 Nissan Sentra

    1 Answer

    The service shop left my oil cap off after an oil change. So far they have brought in 3 different caps, and none of them fit! Two came from parts stores and one from Mazda. I have a 2004 Mazda 6i 2.3L 4...


    I had the same problem finding a replacement oil cap after my husband left the cap off. The usual auto parts stores didn't have one that fit. I had to order the cap through the dealership. The problem was that Mazda changed the oil cap midway through the production year. Try oil caps from the years on either side of yours: if you have a 2004 vehicle, try getting a 2003 and 2005 oil cap.

    Feb 11, 2010 | 2004 Mazda 6

    1 Answer

    Oil cap won't come off 97 Ford F150.


    Solved the problem by taking it to a shop and being overcharged to have a tech remove it with pliers and breaking it in the process. Had to buy yet another new oil cap. Problem not solved cause this new cap won't budge either.

    Jun 05, 2009 | 2001 Dodge Ram 1500 Truck 2WD

    1 Answer

    Leaking oil from oil cap


    The problem is there is to much crank case pressure, make sure the PCV ( positive crankcase ventalation) valve is working correctly.

    Oct 07, 2008 | 1986 Volvo 740

    1 Answer

    Oil refill cap


    Replacement oil fill caps are readily available. I had to use a large pair of channel locks around the oil cap and twisting it off.

    Aug 13, 2008 | 2000 Dodge Caravan

    1 Answer

    Crank shaft movement


    did you check the pulley on the crank shaft ??
    is it warped ?? ( bent )
    because i do not think that the truck will run with the crankshaft moving.....back and forth.
    so in any case you have a lot of work to do.
    here is how to remove the crank shaft.
    REMOVAL
    1. Remove the oil pan.
    2. Remove the oil pump from the rear main bearing cap.
    3. Remove the vibration damper.
    4. Remove the timing chain cover.
    5. Identify bearing caps before removal. Remove bearing caps and bearings one at a time.
    6. Lift the crankshaft out of the block.
    7. Remove and discard the crankshaft rear oil seals.
    8. Remove and discard the front crankshaft oil seal.
    INSTALLATION
    1. Lightly oil the new upper seal lips with engine oil.
    2. Install the new upper rear bearing oil seal with the white paint facing towards the rear of the engine.
    3. Position the crankshaft into the cylinder block.
    4. Lightly oil the new lower seal lips with engine oil.
    5. Install the new lower rear bearing oil seal into the bearing cap with the white paint facing towards the rear of the engine.
      1. Apply 5 mm (0.20 inch) drop of Loctite 518, or equivalent, on each side of the rear main bearing cap. DO NOT over apply sealant or allow the sealant to contact the rubber seal. Assemble bearing cap to cylinder block immediately after sealant application.
      2. lb align the bearing cap, use cap slot, alignment dowel and cap bolts. DO NOT remove excess material after assembly. DO NOT strike rear cap more than 2 times for proper engagement.
      3. Clean and oil all cap bolts. Install all main bearing caps. Install all cap bolts and alternately tighten to 115 Nm (85 ft. lbs.) torque.
      4. Install oil pump.
      5. Install the timing chain cover.
      6. Install the vibration damper.
        1. Apply Mopar Silicone Rubber Adhesive Sealant, or equivalent, at bearing cap to block joint to provide cap to block and oil pan sealing. Apply enough sealant until a small amount is squeezed out. Withdraw nozzle and wipe excess sealant off the oil pan seal groove.
        2. Install new front crankshaft oil seal.
        3. Immediately install the oil Dan.
    if you have an email address i can send some images

    Jun 07, 2008 | 1998 Dodge Dakota

    Not finding what you are looking for?
    2006 Jeep Liberty Logo

    Related Topics:

    68 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jeep Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8140 Answers

    Are you a Jeep Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...