Question about 1997 Chrysler Sebring

1 Answer

Inigition switch replacement - 1997 Chrysler Sebring

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

On what kind of car? Do you have the keys that operate it...more info needed.

Posted on Aug 02, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I can not remove the inigition key from my 2002 volvo c70

it is the shifter lock out cable thats gos from the inigition switch to the floor shifter,remove the cable from the inigition switch presto the key will come out agsts52 @comcast .net

Sep 11, 2010 | 2002 Volvo C70

1 Answer

Mapsensor was the problem they stated then the say the number 3 plug was misfire and comp is 50psi on 3 cylinder needs engine?

wow your in for a bill.first compression test needs to be done when the cylinder is TDC(top dead center).your be shocked how many mechanics dont know how to do this.i run into a few.compression that low head gasket blowen.need to replace if comp is at 50psi correct.get a second option and check.usually its misfiring because compression,inigition modular,wire bad internal or connection,spark plug.or fuel injector.get a second option or you going to the bank on this one.compression first check.

Aug 17, 2010 | 2002 Chevrolet Monte Carlo

1 Answer

Lights, locks, wipers not working 2001 Dodge Durango R/T

Your Durango possibly needs a CTM or Central Timing Module. The module is located behind the kick panel down by the drivers feet on the left.

The repair commands a ~$500 price for parts and labor, and they will need both your remote fobs to program them to the system.

Jun 17, 2010 | 2000 Dodge Durango

1 Answer

Inigition will not turn in park. bang on shifter to turn key and start car. 2000 grand am automatic

sounds like the shifter lock seliniod is sticking or going bad,you can try to open shifter area and clean and lube linkages,lots of time coffe or soda spills and make the linkage stick,

Apr 19, 2010 | 2000 Pontiac Grand Am GT

1 Answer

Heater unit will not shut off with inigition switch in off position. 2005 escalade. Any suggestions. I know its got to be a relay somewhere.

If you mean the blower motor then the problem is your blower motor resistor module.It is on the passengers side under the dash.The wires from the blower motor will go to the resistor.If you go to the dealership and buy one you will know what to look for.I have tried to get these at a auto parts store but could only get them from the dealership.There is a service bulletin and the number is 06-01-39-002C.The part number 89018849 w/rear heater and 89018964 w/front heater only.Hope this helps.Good luck.

Dec 24, 2009 | Cadillac Escalade Cars & Trucks

1 Answer

Inigition switch locks but will not unlock . Key can be removed but you have to hold pressure on switch.

How do you change a heater core on a 2002 Mercury Sable? My husband is going to try to attempt it but we do not have instructions.

Dec 04, 2009 | 1995 Buick LeSabre

1 Answer

Inigition and brake light

you need to replace the brake light sockets. The little springs wear out and then there is no tension against the bulb contacts. Do not buy used sockets. Bad too.Buy on ebay cheap.But check with a Mercury dealer first to see if there is an open recall for this issue on your van. They will need your 17 digit VIN and can do on the phone. Ask for service dept.Also, go here for all Villager help.

Jun 10, 2009 | 1999 Mercury Villager

1 Answer

No start

I wash my car's motor and then starting with dificult and go off. I continue traying starting one and ones again. I changed rotor, inigition cap, and sparks and nothing. I continue starting but the car don,t stay on and the car don't run.

Jul 26, 2008 | 1987 Nissan 200SX

Not finding what you are looking for?
1997 Chrysler Sebring Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides