Question about 1996 Plymouth Voyager

1 Answer

How doyou replace the c v joint on a 1996 voyager

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 6,674 Answers

What most people do now, rather than go through the aggravation, then maybe have to do other end later, is just buy complete half shaft for about $60.00 and replace whole thing. Take old one with you for matching up plus $40 or so core charge if you keep old one.

Posted on Aug 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

U joints for a 1994 plymouth voyager


2 axles- 1 on each side front. 2 CV joints per axle. Better to replace axle assy complete.

Mar 01, 2014 | 1994 Plymouth Voyager

1 Answer

1996 plymouth voyager 3.3 fuel gauge don't work!


This is a wiring problem. I have an intermitten issue with the gauge. I have checked the connections at the junction box and BCM, but it did not cause any changes. One I have not checked but hope fixes it is a "cold" solder joint on the panel PCB. I have read other issues with it, so it may be the same.
I suggest you check there first also.

Oct 22, 2011 | 1996 Plymouth Voyager

1 Answer

When backing up and truning left there is a grinding sound on the front left what is this?


It could be the half shaft. The joints should be completely covered with a rubber boot. If it is torn or missing, the joint will become damaged.
You should not drive it if it is the half shaft since if it fails altogether, it could cause you to have an accident.

Oct 17, 2011 | 1996 Plymouth Voyager

1 Answer

1996 grand voyager need to know how to replace front lower control arm bushings, tools needed ect...


cheaper to buy a new one that already has new ball joint and bushing installed, just swap out old one.no fuss no rental tools , etc.. cheap around 120.00 shop around. u will pay that for ball joint and bushings.

Mar 20, 2011 | 1996 Plymouth Grand Voyager

1 Answer

Had sway bars fixed and it vibrates worse now than before once over 60


Didn't see that as the fix for the problem. My guess is tires out of balance or worn cv joints in front axles. Cheaper to replace axle half shafts than a single cv joint kit at discount auto supplies like checker,autozone,etc. Lastly, wheel hub bearing/s. A tire shop with a mechanic could tell you.

Aug 12, 2010 | 1996 Plymouth Voyager

1 Answer

Noise coming from near side front when going around a right hand bend 2001 chrysler voyager 2.4 se


it could be the CV joint is faulty, check the rubber boot on the drive axle on the near side front wheel to see if it is split or completely destroyed,if it is damaged the dirt has got into the CV joint & caused the damage & the CV joint will have to be replaced........hope this helps......cheers

Aug 04, 2010 | 2001 Chrysler Voyager

1 Answer

Need diagram on what has to be removed to replace the driver side trans axle


Not much to it,
remove wheel,remove axle nut,remove bolt and nut that pinch lower ball joint in place,it will either be an 18mm or a 21mm,pry lower control down to detach and separate ball joint,tap CV shaft in where you took the nut off,
hold out on rotor assembly while pushing CV shaft in ward,When you have the CV out of the bearing and rotor assembly,Tap inside CV joint out of transmission.

Dec 16, 2009 | 1996 Plymouth Grand Voyager

1 Answer

1996 Ply. Voyager. Wipers not always intermittant.


it sounds like the control board on the wiper motor has gone bad you'll have to replace the the motor

Oct 15, 2009 | 1996 Plymouth Grand Voyager

1 Answer

1996 Plymoth Voyager runs rough only when cold


service eng light on? scan retrieve codes if no code your gue$$ing

Nov 19, 2008 | 1996 Plymouth Voyager

1 Answer

Replacing fuel pump on a 1996 Plymouth Voyager


CHECK TO SEE IF THEY KNOCKED THE METAL TABS DOWN ONTO RING FIRST. IF NOT SOAK RING WITH PENETRATING OIL FOR A DAY THEN TRY TO GET OFF.

Sep 09, 2008 | 1996 Plymouth Voyager

Not finding what you are looking for?
1996 Plymouth Voyager Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...